Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 103
Symptom:
DRIVER
DOOR
CENTRAL
LOCK
(ARM)/UNLOCK
(DISARM)
SWITCH FAILURE
When Monitored and Set Condition:
DRIVER DOOR CENTRAL LOCK (ARM)/UNLOCK (DISARM) SWITCH FAILURE
When Monitored:
Continuously
Set Condition:
If the BCM detect a signal on the Driver Cylinder Lock Switch Mux circuit
for over 10 seconds this code will set and will ignore the offending input until it is corrected.
POSSIBLE CAUSES
BINDING DRIVER CYLINDER LOCK SWITCH
DRIVER CYLINDER LOCK SWITCH SHORTED TO VOLTAGE
DRIVER CYLINDER LOCK SWITCH MUX CIRCUIT SHORTED TO VOLTAGE
WIRING HARNESS INTERMITTENT DEFECT
BODY CONTROL MODULE - DRIVER CYLINDER LOCK SWITCH FAILURE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase DTC’s.
Insert the key in the Driver Cylinder Lock Switch and rotate the key to the lock and
unlock positions several times.
With the DRBIII
t, read DTC’s.
Did this DTC reset?
All
Yes
→ Go To 2
No
→ Go To 6
2
Insert the key in the Driver Cylinder Lock Switch and rotate the key to the lock and
unlock positions.
Does the key bind in any position?
All
Yes
→ Repair or replace the Driver Cylinder Lock Switch as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Disconnect the Driver Cylinder Lock Switch harness connector.
Turn the ignition on.
With the DRBIII, enter
9Body Computer9 then 9Sensors9 and observe the Dr Door
Disarm SW voltage
Is there any voltage present?
All
Yes
→ Go To 4
No
→ Replace the Driver Cylinder Lock Switch.
Perform BODY VERIFICATION TEST - VER 1.
397
POWER DOOR LOCKS/RKE
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the Driver Cylinder Lock Switch harness connector.
Disconnect the BCM
9C49 harness connector.
Turn the ignition on.
Measure the voltage of the Driver Cylinder Lock Switch Mux circuit.
Is there any voltage present?
All
Yes
→ Repair the Driver Cylinder Lock Switch Mux circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
If there are no possible causes remaining, view repair.
All
Repair
Replace the Body Control Module in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
6
Turn the ignition off.
NOTE: Using the wiring diagram/schematic as a guide, inspect the wiring
and connectors.
Were any problems found?
All
Yes
→ Repair wiring harness or connectors as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
398
POWER DOOR LOCKS/RKE
DRIVER DOOR CENTRAL LOCK (ARM)/UNLOCK (DISARM) SWITCH
FAILURE —
Continued
Symptom:
RKE FOB BATTERY LOW
When Monitored and Set Condition:
RKE FOB BATTERY LOW
When Monitored:
Anytime an RKE message is received from the transmitter.
Set Condition:
RKE receiver detects an RKE FOB battery low signal (less than 3 volts)
for 5 consecutive button presses.
POSSIBLE CAUSES
BATTERIES LOW
TRANSMITTER - LOW VOLTAGE OUTPUT
TEST
ACTION
APPLICABILITY
1
To determine which transmitter set the code, press any button on each transmitter.
If a chime in the BCM is heard when a button is pressed, that is the problem
transmitter.
Test the voltage of each battery in the problem transmitter..
Is the voltage at or above 3.0 in each battery?
All
Yes
→ Replace the RKE Transmitter.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the batteries.
Perform BODY VERIFICATION TEST - VER 1.
399
POWER DOOR LOCKS/RKE
Symptom:
RKE PROGRAM MODE ENTERED WITHOUT PROGRAM REQUEST
When Monitored and Set Condition:
RKE PROGRAM MODE ENTERED WITHOUT PROGRAM REQUEST
When Monitored:
Continuously.
Set Condition:
The BCM receives an indication from the RKE module that it has entered
program mode without the BCM requesting so.
POSSIBLE CAUSES
REMOTE KEYLESS ENTRY MODULE
RKE PROGRAM MODE ENTERED WITHOUT PROGRAM REQUEST
TEST
ACTION
APPLICABILITY
1
Note: This DTC will only set if the BCM receives an indication from the RKE
module that it has entered program mode without the BCM requesting so.
Replace the Remote Keyless Entry Module and program a transmitter..
With the DRBIII, clear DTCs.
Operate the Door Locks several times with the RKE transmitter.
With the DRBIII
t, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Body Control Module in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ If the replaced module was a test unit only, replace the RKE
module. Program all transmitters used with this vehicle.
Perform BODY VERIFICATION TEST - VER 1.
400
POWER DOOR LOCKS/RKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст