Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 49
Symptom:
*CHIME INOPERATIVE WITH DRIVER SEAT BELT UNFASTENED
POSSIBLE CAUSES
SEAT BELT SWITCH STATUS ON DRBIII
t
SEAT BELT SWITCH SHORTED
SEAT BELT SWITCH SENSE SHORT TO GROUND
INSTRUMENT CLUSTER - SEAT BELT SWITCH SHORTED
TEST
ACTION
APPLICABILITY
1
Ensure the drivers seat belt is unfastened.
With the DRBIII
t, select Electro Mech Cluster Input/Output.
Turn the ignition on.
Read the Seat Belt Sw status.
Does the DRBIII display Seat Belt Sw: Closed
All
Yes
→ Go To 2
No
→ Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.
2
Disconnect the Seat Belt Switch connector.
With the DRBIII
t, select Electro Mech Cluster Input/Output.
Turn the ignition on.
Read the seat Belt Sw status.
Does the DRBIII display Seat Belt Sw: Closed
All
Yes
→ Go To 3
No
→ Repair the Seat Belt switch pigtail wiring or replace the Buckle
assembly.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Removed the Instrument Cluster from the instrument panel.
Disconnect the Seat Belt Switch connector.
Measure the resistance between ground and the Seat Belt Switch Sense circuit.
Is the resistance below 100.0 ohms?
All
Yes
→ Repair the Seat Belt Switch Sense wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
4
If there are no possible causes remaining, view repair.
All
Repair
Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.
181
CHIME
Symptom:
*CHIME INOPERATIVE WITH EXTERIOR LIGHTS ON AND DRIV-
ERS DOOR OPEN
POSSIBLE CAUSES
OPEN HEADLAMP SWITCH OUTPUT
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
The Driver’s Door Ajar switch must be operational for the result of this test to be
valid.
The Key-In Ignition switch chime function must be operational for the result of this
test to be valid.
Turn the ignition off.
Remove the Body Control Module from the Junction Block.
Turn the headlamps on.
Measure the voltage of the Headlamp Switch Output circuit in the Junction Block
internal 12-way connector.
Is the voltage above 10.0 volts?
All
Yes
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the Head Lamp Switch Output circuit for an open from the
headlamp switch.
Perform BODY VERIFICATION TEST - VER 1.
182
CHIME
Symptom:
*CHIME INOPERATIVE WITH KEY-IN IGNITION AND DRIVER
DOOR OPEN
POSSIBLE CAUSES
OBSERVE THE KEY-IN IGNITION SWITCH STATUS
KEY-IN IGNITION SWITCH OPEN
KEY-IN IGNITION SWITCH GROUND CIRCUIT OPEN
KEY-IN IGNITION SWITCH SENSE CIRCUIT OPEN
BCM - INCORRECT KEY - IN IGNITION SWITCH STATUS
TEST
ACTION
APPLICABILITY
1
The door ajar switch must be operational for the result of this test to be valid.
NOTE: Ensure that the Key is still in the Ignition Switch.
With the DRBIII
t enter Body Computer then Input Output and read the Key-In
Ignition Switch status.
Does the DRB display: KEY-IN IGN: CLOSED?
All
Yes
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition on.
Disconnect the Ignition Switch C3 harness connector.
Connect a jumper between the Key-In Ignition Switch Sense circuit and the Ground
circuit.
With the DRBIII
t, enter Body Computer then Input/Output and observe the Key-In
Ignition Switch status.
Does the DRBIII display Key-In Ign: Closed?
All
Yes
→ Replace the Ignition Switch.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the Ignition Switch C3 harness connector.
Turn all lights off.
Measure the resistance between ground and the ground circuit in the ignition switch
connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
183
CHIME
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the Ignition Switch C3 harness connector.
Disconnect the Body Control Module C1 harness connector.
Measure the resistance of the Key-In Ignition Switch Sense circuit between the
ignition switch connector and the BCM harness C1 connector .
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 5
No
→ Repair the Key-In Ignition Switch Sense circuit for an open
Perform BODY VERIFICATION TEST - VER 1.
5
If there are no possible causes remaining, view repair.
All
Repair
Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
184
CHIME
*CHIME INOPERATIVE WITH KEY-IN IGNITION AND DRIVER DOOR
OPEN —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст