Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 50
Symptom:
*CHIME SOUNDS WITH DRIVER SEAT BELT FASTENED
POSSIBLE CAUSES
SEAT BELT SW STATUS WRONG-OPEN
SEAT BELT SWITCH OPEN
GROUND WIRE OPEN
SEAT BELT SW SEN OPEN
INSTRUMENT CLUSTER - SEAT BELT SENSE OPEN
TEST
ACTION
APPLICABILITY
1
Ensure the drivers seat belt is fastened.
With the DRB III select: Electro Mech Cluster Input/Outputs.
Turn the ignition on.
Read the Seat Belt SW status.
Does the DRB III show Seat Belt SW: CLOSED?
All
Yes
→ Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Disconnect the Seat Belt Switch connector.
Turn all lights off. Trip the door lock latch to turn the courtesy lamps off.
Measure the resistance of the Ground circuit in the Seat Belt connector to ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 3
No
→ Repair the open ground wire.
Perform BODY VERIFICATION TEST - VER 1.
3
Disconnect the Seat Belt Switch connector.
Connect a jumper wire between Seat Belt Switch Sense CKT and the Ground CKT in
the Seat Belt Switch connector.
With the DRB III select: Electro Mech Cluster Input/Outputs.
Turn the ignition on.
Read the Seat Belt SW status.
Does the DRB III show Seat Belt SW: CLOSED?
All
Yes
→ Repair the Seat Belt switch pigtail wiring or replace the Buckle
assembly.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
4
Turn the ignition off.
Remove the Instrument Cluster from the instrument panel.
Disconnect the Seat Belt Switch connector.
Measure the resistance of the Seat Belt Switch Sense circuit between the Instrument
Cluster connector and the Seat Belt Switch connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 5
No
→ Repair the open Seat Belt Switch Sense circuit.
Perform BODY VERIFICATION TEST - VER 1.
185
CHIME
TEST
ACTION
APPLICABILITY
5
If there are no possible causes remaining, view repair.
All
Repair
Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.
186
CHIME
*CHIME SOUNDS WITH DRIVER SEAT BELT FASTENED —
Continued
Symptom:
*CHIME SOUNDS WITH DRIVERS DOOR OPEN AND KEY RE-
MOVED FROM IGNITION
POSSIBLE CAUSES
KEY-IN IGNITION SWITCH STATUS WRONG
KEY-IN IGNITION SWITCH STATUS WRONG
KEY-IN IGNITION SW SENSE SHORT TO GROUND
BODY CONTROL MODULE - KEY-IN IGNITION SHORTED
TEST
ACTION
APPLICABILITY
1
Ensure all exterior lamps are off.
With the DRB III select: Body Computer Input/Output.
Remove the key from the ignition switch.
Read the Key-In Ignition status.
Does the DRB III show Key-In Ign: CLOSED?
All
Yes
→ Go To 2
No
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the Ignition Switch C3 harness connector.
Disconnect the Body Control Module C1 harness connector.
Measure the resistance of the Key-in Ignition Switch Sense circuit to ground.
Is the resistance below 100.0 ohms?
All
Yes
→ Repair the Key-in Ignition Switch Sense circuit to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Disconnect the Ignition Switch C3 connector.
With the DRBIII
t select: Body Computer Input/Output.
Read the Key-In Ignition Status.
Does the DRBIII
t display Key-In Ign CLOSED?
All
Yes
→ Go To 4
No
→ Replace the Ignition Switch.
Perform BODY VERIFICATION TEST - VER 1.
4
If there are no possible causes remaining, view repair.
All
Repair
Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
187
CHIME
Symptom:
*VEHICLE SPEED WARNING CHIME PROBLEM
POSSIBLE CAUSES
INCORRECT COUNTRY CODE PROGRAMMED IN BCM
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Note: The vehicle speed warning chime is for Gulf Coast Countries only.
With the DRBIII
t, check the Body Control Module country code setting.
Is the country code incorrect?
All
Yes
→ Program the correct country code setting.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace and program the Body Control Module in accordance
with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
188
CHIME
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст