Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 676
![](/vehicles/ged/eoowintisin/couthalle/zpa.png)
ADJUSTABLE QUARTER GLASS JR-27
TABLE OF CONTENTS
page
page
ADJUSTABLE QUARTER GLASS JR-27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
. . . . . . . . . . . . . . . . . . . . . . . . 101
ADJUSTABLE QUARTER
GLASS JR-27
REMOVAL
(1) Raise quarter glass to full up position, if possi-
ble, to aid in removal.
(2) Remove quarter trim panel.
(3) Partially lower convertible top.
(4) Disconnect wire connector to power window
motor.
(5) Remove fasteners holding quarter window mod-
ule to inner quarter panel (Fig. 1).
(6) Lift quarter window module upward and out
opening at top of quarter panel.
(7) Separate quarter glass from quarter window
module (Fig. 2).
INSTALLATION
(1) Lower quarter window module into position
through opening in top of quarter panel.
(2) Install fasteners holding quarter window mod-
ule to inner quarter panel.
(3) Connect wire connector to power window motor.
(4) Raise glass lift channel to full up position.
(5) Position quarter glass on quarter window mod-
ule.
(6) Loosely install fasteners holding quarter glass
to quarter window module.
(7) Lower and secure convertible top.
(8) Adjust quarter glass as necessary (Refer to 23 -
BODY/ADJUSTABLE QUARTER GLASS - ADJUST-
MENTS).
(9) Install quarter trim panel.
ADJUSTMENTS
QUARTER GLASS ADJUSTMENT
NOTE: The door glass must be properly adjusted
prior to performing any quarter glass adjustments.
(Refer to 23 - BODY/DOOR - FRONT/DOOR GLASS -
ADJUSTMENTS)
Fig. 1 Quarter Window Module
1 - QUARTER GLASS
2 - INNER QUARTER PANEL
3 - QUARTER WINDOW MODULE
Fig. 2 Quarter Glass
1 - QUARTER WINDOW MODULE
2 - POWER QUARTER WINDOW MOTOR
3 - QUARTER GLASS
JR
ADJUSTABLE QUARTER GLASS JR-27
23 - 101
![](/vehicles/ged/eoowintisin/couthalle/vens.png)
UP-STOP ADJUSTMENTS
NOTE: Up-stop nuts are behind the quarter panel
speakers, and can be accessed without removing
the trim panel.
(1) Remove the speaker cover, speaker and speaker
cup, if equipped. Peel back the sealing patch to
access forward up-stop. (Fig. 3)
(2) Remove center and rear side rail weatherstrips
from side rail weatherstrip retainer channels.
(3) Loosen up-stop nuts.
(4) Raise quarter glass.
(5) Slide up-stop to achieve proper glass to weath-
erstrip retainer gap. (Fig. 4)
(6) Tighten all fasteners.
(7) Install center and rear side rail weatherstrips
to side rail weatherstrip retainer channels.
(8) Cycle quarter glass between full up and full
down positions. Verify operation and adjust as neces-
sary.
(9) Verify that the top edge of the door glass is
beneath the lip of the weatherstrip.
(10) Re-apply
the
sealing
patch.
Install
the
speaker cup, speaker and speaker cover.
Fig. 3 UP STOP ADJUSTMENTS
1 - REAR UP STOP BOLT
2 - FRONT UP STOP BOLT
3 - QUARTER TRIM PANEL
4 - SPEAKER OPENING
Fig. 4 QUARTER GLASS ADJUSTMENT SPECIFICATIONS
23 - 102
ADJUSTABLE QUARTER GLASS JR-27
JR
ADJUSTABLE QUARTER GLASS JR-27 (Continued)
![](/vehicles/ged/eoowintisin/couthalle/inoundy.png)
BOTTOM OF GLASS – INBOARD/OUTBOARD
ADJUSTMENTS
(1) Remove the speaker cover, speaker and speaker
cup, if equipped.
(2) Using a suitable offset wrench, loosen the
upper forward jack screw set nut. (Fig. 5)
(3) Using a suitable allen wrench (Fig. 6), rotate
the jack-screw to achieve the proper gap between the
door glass and the quarter glass seal (Fig. 4). Tighten
all fasteners prior to measuring the gaps.
(4) Install speaker cup, if equipped, speaker and
cover.
TOP OF GLASS – INBOARD/OUTBOARD
ADJUSTMENTS
(1) Remove quarter trim panel. (Refer to 23 -
BODY/INTERIOR/QUARTER
PANEL
TRIM
-
REMOVAL)
NOTE: Alternatively, the lower adjustment can be
accessed through a hole at the bottom of the quar-
ter trim panel. This hole can be located by remov-
ing the rear seat cushion. (Refer to 23 - BODY/
SEATS/SEAT CUSHION - REMOVAL)
(2) Remove center and rear side rail weatherstrips
from side rail weatherstrip retainer channels.
(3) Using a suitable wrench, loosen the lower jack
screw jam nuts.
(4) Raise quarter glass.
(5) Using a suitable allen wrench, rotate jack-
screws to achieve the proper gap between the door
glass weatherstrip retainer channel. (Fig. 4)
(6) Verify that the quarter glass maintains even
contact with the outer belt weatherstrip.
(7) Install center and rear side rail weatherstrips
to side rail weatherstrip retainer channels.
(8) Cycle quarter glass between full up and full
down positions. Verify operation and adjust as neces-
sary.
(9) Tighten all fasteners.
(10) Verify that the top edge of the door glass is
beneath the lip of the weatherstrip with glass in the
full up position.
(11) Install quarter trim panel. (Refer to 23 -
BODY/INTERIOR/QUARTER
PANEL
TRIM
-
INSTALLATION)
GLASS – FRONT/REAR ADJUSTMENT
(1) Remove quarter trim panel. (Refer to 23 -
BODY/INTERIOR/QUARTER
PANEL
TRIM
-
REMOVAL)
(2) Remove center and rear side rail weatherstrips
from side rail weatherstrip retainer channels.
(3) Loosen glass attachment bolts.
(4) Raise quarter glass and position correctly. (Fig.
4)
(5) Tighten all fasteners.
(6) Install center and rear side rail weatherstrips
to side rail weatherstrip retainer channels.
(7) Cycle quarter glass between full up and full
down positions. Verify operation and adjust as neces-
sary.
(8) Install quarter trim panel. (Refer to 23 -
BODY/INTERIOR/QUARTER
PANEL
TRIM
-
INSTALLATION)
QUARTER GLASS ALIGNMENT VERIFICATION
(1) Raise door glass to full up position.
Fig. 5 FORWARD JACK SCREW ADJUSTMENT
1 - JACK SCREW ADJUSTMENT
2 - QUARTER TRIM PANEL
3 - SPEAKER OPENING
Fig. 6 IN/OUT ALLEN ADJUSTMENT
1 - SPEAKER OPENING
2 - TRIM PANEL HOLE
3 - QUARTER TRIM PANEL
4 - ALLEN WRENCH
JR
ADJUSTABLE QUARTER GLASS JR-27
23 - 103
ADJUSTABLE QUARTER GLASS JR-27 (Continued)
![](/vehicles/ged/eoowintisin/couthalle/cyodin.png)
(2) Cycle quarter glass between full up and full
down positions.
(3) Verify that quarter glass operates smoothly and
maintains correct alignment to convertible top and
door glass.
NOTE: The alignment to door glass can be checked
with the “paper strip test”. Place a piece of paper
on the quarter glass seal and close the door. Slide
the paper along the length of the seal - there should
be some resistance to pulling the paper out. (Fig. 7)
(4) Verify that quarter glass weatherstrip fully
contacts door glass.
(5) Verify that no scissoring of the door glass and
weatherstrip occurs.
(6) If any of the above conditions are found,
(a) Adjust quarter glass.
(b) Adjust the door glass as necessary to cure
the condition.
Fig. 7 QUARTER GLASS ADJUSTMENT
VERIFICATION
1 - DOOR GLASS
2 - QUARTER GLASS
3 - PAPER STRIP
23 - 104
ADJUSTABLE QUARTER GLASS JR-27
JR
ADJUSTABLE QUARTER GLASS JR-27 (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст