Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 658
INSTALLATION
(1) Position decklid latch on vehicle.
(2) Loosely install bolts attaching decklid latch to
decklid.
(3) Tighten bolts to 12 N·m (106 in. lbs.) torque.
(4) Align decklid latch to marks made previously
on decklid and tighten bolts.
(5) Connect wire connectors to remote release sole-
noid, if so equipped.
(6) Verify fit of decklid to deck panel and decklid
latch operation. Adjust as necessary.
DECKLID LATCH STRIKER
REMOVAL
(1) Release decklid latch and open decklid.
(2) Mark outline of decklid latch striker on rear
closure panel to aid in installation.
(3) Remove bolts attaching decklid latch striker to
rear closure panel (Fig. 4).
(4) Remove striker from vehicle.
INSTALLATION
(1) Position striker in vehicle.
(2) Loosely install bolts attaching decklid latch
striker to rear closure panel.
(3) Align decklid latch striker to marks made pre-
viously on rear closure panel.
(4) Tighten bolts to 12 N·m (106 in. lbs.) torque.
(5) Verify fit of decklid to deck panel and operation
of decklid latch. Adjust as necessary.
DECKLID LOCK CYLINDER
REMOVAL
(1) Release decklid latch and open decklid.
(2) Remove decklid latch.
(3) Remove clip attaching decklid lock cylinder to
security alarm switch, if so equipped (Fig. 5).
(4) Remove security alarm switch, if so equipped.
(5) Remove clip attaching decklid lock cylinder to
decklid.
(6) Remove decklid lock cylinder from vehicle.
INSTALLATION
(1) Position decklid lock cylinder on vehicle.
(2) Install clip holding decklid lock cylinder to
decklid.
(3) Install security alarm switch, if so equipped.
(4) Install clip attaching decklid lock cylinder to
security alarm switch, if so equipped.
(5) Install decklid latch.
Fig. 4 DECKLID LATCH STRIKER
1 - REAR CLOSURE PANEL
2 - TRUNK LATCH STRIKER
Fig. 5 DECKLID LOCK CYLINDER
1 - DECKLID LOCK CYLINDER
2 - DECKLID
3 - RETAINER CLIP
JR
DECKLID/HATCH/LIFTGATE/TAILGATE
23 - 29
DECKLID LATCH (Continued)
EMERGENCY RELEASE CABLE
REMOVAL
(1) Remove the decklid latch cover (Fig. 6).
(2) Unclip cable and handle assembly (Fig. 7).
INSTALLATION
(1) Clip emergency release cable onto the latch.
(2) Install the decklid latch cover.
Fig. 6 DECKLID LATCH COVER
1 - Push pin
2 - Decklid latch cover
Fig. 7 EMERGENCY RELEASE CABLE
1 - Release Cable Clip
2 - Decklid Latch
23 - 30
DECKLID/HATCH/LIFTGATE/TAILGATE
JR
DOOR - FRONT
TABLE OF CONTENTS
page
page
CHECK STRAP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . 32
DOOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . 33
DOOR GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . 34
DOOR GLASS INNER BELT STABILIZER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . 39
EXTERIOR HANDLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . 39
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . . 40
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . 41
LATCH STRIKER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
. . . . . . . . . . . . . . . . . . . . . . . . . 42
LOCK BUTTON BELL CRANK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
. . . . . . . . . . . . . . . . . . . . . . . . . 42
LOCK CYLINDER
. . . . . . . . . . . . . . . . . . . . . . . . . 43
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
. . . . . . . . . . . . . . . . . . . . . . . . . 43
SIDE VIEW MIRROR FLAG/DOOR GLASS
CHANNEL
REMOVAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
. . . . . . . . . . . . . . . . . . . . . . . . . 43
TRIM PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
. . . . . . . . . . . . . . . . . . . . . . . . . 44
REAR VERTICAL GUIDE BAR
. . . . . . . . . . . . . . . . . . . . . . 45
. . . . . . . . . . . . . . . . . . . 45
WINDOW REGULATOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . 46
. . . . . . . . . . . . . . . . 46
. . . . . . . . . . . . . . . . . . . . . . . 47
APPLIQUE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
. . . . . . . . . . . . . . . . . . . . . . . . . 47
DOOR PIN ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
. . . . . . . . . . . . . . . . . . . . . . . . . 48
. . . . . . . . . . . . . . . . . . . . . . . . 48
WATER DAM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
. . . . . . . . . . . . . . . . . . . . . . . . . 49
JR
DOOR - FRONT
23 - 31
CHECK STRAP
REMOVAL
(1) Remove door trim panel (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - REMOVAL).
(2) Remove water dam as necessary to gain access
(Refer to 23 - BODY/DOOR - FRONT/WATERDAM -
REMOVAL).
(3) Remove bolts attaching check strap to lower
A–pillar.
(4) Remove bolts attaching check strap to door end
frame (Fig. 1).
(5) Remove door check strap from vehicle.
INSTALLATION
(1) Position door check strap on vehicle (Fig. 1).
(2) Install bolts attaching check strap to door end
frame.
(3) Install bolts attaching check strap to lower
A-pillar.
(4) Install water dam (Refer to 23 - BODY/DOOR -
FRONT/WATERDAM - INSTALLATION).
(5) Install door trim panel (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - INSTALLATION).
DOOR
REMOVAL
(1) Open and support door on a suitable lifting
device.
(2) Mark
hinges
attachment
locations
with
a
grease pencil or other suitable device to aid installa-
tion.
(3) Disengage wire connector at hinge A-pillar.
(4) Remove bolts attaching door check strap to
hinge A-pillar (Fig. 2).
(5) Remove the nuts attaching the door to the door
hinges and remove the door from the vehicle.
INSTALLATION
(1) Position door onto the door hinges and install
the nuts.
(2) Install bolts attaching door check strap to
hinge pillar.
(3) Connect wire connector at hinge pillar.
(4) Verify door fit and operation. Adjust the door
for flushness and parallel gaps as necessary. (Refer to
23 - BODY/DOOR - FRONT/DOOR - ADJUST-
MENTS).
Fig. 1 Front Door Check Strap
1 - FRONT DOOR
2 - DOOR CHECK STRAP
3 - DOOR FACE
Fig. 2 FRONT DOOR HINGES
1 - UPPER DOOR HINGE NUTS
2 - UPPER DOOR HINGE
3 - ELECTRICAL CONNECTIONS
4 - CHECK STRAP
5 - LOWER HINGE
6 - LOWER HINGE NUTS
23 - 32
DOOR - FRONT
JR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст