Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 657
Fig. 21 SIDE CENTER RAIL WEATHERSTRIP
1 - WEATHERSTRIP
Fig. 22 WEATHERSTRIP ATTACHING SCREWS
1 - ATTACHING SCREWS
Fig. 23 SIDE CENTER RAIL REAR ATTACH SCREW
1 - REAR BOLT
Fig. 24 SIDE CENTER RAIL FRONT ATTACHING
SCREWS
1 - ATTACHING BOLTS
JR
CONVERTIBLE TOP
23 - 25
SIDE CENTER RAIL (Continued)
INSTALLATION
(1) Place center side rail in position.
(2) Install front pivot bolts (Fig. 25).
(3) Install pivot arm bolt at side rail (Fig. 26).
(4) Install lower rear pivot bolt.
(5) Install weatherstrip retainer (Fig. 27), and
weatherstrip for side glass on the center side rail
(Fig. 28).
(6) Remove the device propping up the top.
(7) Connect headliner push pin fasteners at quar-
ter panel.
(8) Connect fasteners attaching headliner and top
cover straps.
(9) Install quarter trim panel. (Refer to 23 -
BODY/INTERIOR/QUARTER
PANEL
TRIM
-
INSTALLATION).
(10) Install speaker grille. (Refer to 23 - BODY/IN-
TERIOR/QUARTER PANEL TRIM - INSTALLA-
TION).
(11) Install sill plate. (Refer to 23 - BODY/INTE-
RIOR/DOOR SILL TRIM - INSTALLATION).
(12) Install rear seat back. (Refer to 23 - BODY/
SEATS/REAR SEAT BACK - INSTALLATION).
(13) Install rear seat cushion. (Refer to 23 - BODY/
SEATS/SEAT CUSHION - INSTALLATION).
(14) Lower top and latch top.
(15) Raise all windows.
Fig. 25 SIDE CENTER RAIL FRONT ATTACHING SCREWS
1 - ATTACHING BOLTS
Fig. 26 SIDE CENTER RAIL REAR ATTACH SCREW
1 - REAR BOLT
Fig. 27 WEATHERSTRIP ATTACHING SCREWS
1 - ATTACHING SCREWS
Fig. 28 SIDE CENTER RAIL WEATHERSTRIP
1 - WEATHERSTRIP
23 - 26
CONVERTIBLE TOP
JR
SIDE CENTER RAIL (Continued)
DECKLID/HATCH/LIFTGATE/TAILGATE
TABLE OF CONTENTS
page
page
DECKLID
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . 27
GAS PROP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . 28
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . 28
DECKLID LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . 29
DECKLID LATCH STRIKER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 29
DECKLID LOCK CYLINDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 29
EMERGENCY RELEASE CABLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . 30
DECKLID
REMOVAL
(1) Release decklid latch and open decklid.
(2) Mark outline of hinge on decklid to aid in
installation (Fig. 1).
(3) Disconnect all wire connectors from decklid
latch and disconnect wire harness from decklid.
(4) Place suitable padding between decklid and
deck panel to protect paint finish.
(5) With aid of a helper, remove bolts attaching
decklid to decklid hinge.
(6) Remove decklid from vehicle.
INSTALLATION
(1) Position decklid on vehicle.
(2) With aid of a helper, loosely install bolts
attaching decklid to decklid hinge.
(3) Align marks made on decklid previously to
decklid hinge.
(4) Tighten bolts attaching decklid to decklid hinge
to 22.5 N·m (200 in. lbs.) torque.
(5) Connect all wire connectors to decklid latch
and install wire harness to decklid.
(6) Verify fit of decklid to deck panel. Adjust as
necessary.
Fig. 1 Decklid Hinge And Gas Support Cylinder
1 - TRUNK LID
2 - TRUNK HINGE
3 - QUARTER PANEL TROUGH
4 - GAS SUPPORT CYLINDER
JR
DECKLID/HATCH/LIFTGATE/TAILGATE
23 - 27
GAS PROP
REMOVAL
(1) Open decklid.
(2) Remove the gas prop-rod lock caps (Fig. 2).
(3)
Remove prop-rod from mounting studs.
INSTALLATION
(1) Install prop-rod to mounting studs.
(2) Install the gas prop-rod lock caps.
(3) Close decklid.
HINGE
REMOVAL
(1) Open decklid.
(2) Mark outline of hinge on quarter panel trough
and inside of decklid to aid installation.
(3) Place a padded block between the deck panel
and the decklid.
(4) Remove the gas prop-rod lock caps (Fig. 2).
(5) Remove prop-rod from mounting studs.
(6) Remove bolts attaching hinge to decklid.
(7) Place decklid against padded block and hold it
steady.
(8) Remove bolts attaching hinge to quarter panel
trough.
(9) Remove hinge from vehicle.
INSTALLATION
(1) Place hinge in the mark outline of hinge on
quarter panel trough and inside of decklid to aid in
positioning hinge.
(2) Install hinge to vehicle.
(3) Install bolts attaching hinge to quarter panel
trough.
(4) Tighten bolts to 22.5 N·m (200 in. lbs.) torque.
(5) Place decklid against padded block and hold it
steady.
(6) Install bolts attaching hinge to decklid.
(7) Tighten bolts to 22.5 N·m (200 in. lbs.) torque.
(8)
Install prop-rod to mounting studs.
(9) Install the gas prop-rod lock caps.
(10) Remove the padded block between the deck
panel and the decklid.
(11) Close decklid.
DECKLID LATCH
REMOVAL
(1) Release decklid latch and open decklid.
(2) Mark outline of decklid latch on decklid to aid
in installation.
(3) Disconnect wire connectors to remote release
solenoid, if so equipped (Fig. 3).
(4) Remove bolts attaching decklid latch to decklid.
(5) Remove decklid latch from vehicle.
Fig. 2 Gas Prop-Rod Lock Cap
1 - DECKLID HINGE
2 - GAS PROP
3 - GAS PROP-ROD LOCK CAP
Fig. 3 DECKLID LATCH
1 - DECKLID
2 - DECKLID LATCH
3 - WIRE HARNESS
23 - 28
DECKLID/HATCH/LIFTGATE/TAILGATE
JR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст