Chrysler RG Voyager. Manual — part 283
TEST
ACTION
APPLICABILITY
4
Disconnect the Passenger Folding Mirror Relay connector.
Disconnect the Body Control Module C4 connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Passenger Folding Mirror Relay
Control circuit in the relay connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Passenger Folding Mirror Relay Control circuit for a
short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Disconnect the Passenger Folding Mirror Relay connector.
Disconnect the Body Control Module C4 connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance of the Passenger Folding Mirror Relay Control circuit
between the relay connector and the BCM C4 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the Passenger Folding Mirror Relay Control circuit for an
open.
Perform BODY VERIFICATION TEST - VER 1.
1101
POWER MIRROR
PASSENGER MIRROR RELAY OUTPUT OPEN (EXPORT ONLY) —
Continued
Symptom:
PASSENGER MIRROR RELAY OUTPUT SHORT (EXPORT ONLY)
POSSIBLE CAUSES
INTERMITTENT CONDITION
PASSENGER FOLDING MIRROR RELAY
PASSENGER FOLDING MIRROR RELAY CONTROL CIRCUIT SHORTED TO VOLTAGE
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
NOTE: Doors must be closed to allow the mirrors to fold with the power folding
mirror switch.
Attempt to operate the power folding mirror system with the power folding mirror
switch and by opening and closing both front doors with mirrors folded.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 2
No
→ The condition that caused this DTC is currently not present. Use
the wiring diagram/schematic as a guide, and inspect the related
wiring harness for a possible intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.
2
Remove the Passenger Folding Mirror Relay.
Check connectors - Clean/repair as necessary.
Install a substitute relay in place of the Passenger Folding Mirror Relay.
With the DRBIII
t, erase DTC’s.
NOTE: Doors must be closed to allow the mirrors to fold with the power folding
mirror switch.
Attempt to operate the power folding mirror system with the power folding mirror
switch and by opening and closing both front doors with mirrors folded.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 3
No
→ Replace the Passenger Folding Mirror Relay.
Perform BODY VERIFICATION TEST - VER 1.
3
Disconnect the Passenger Folding Mirror Relay connector.
Disconnect the Body Control Module C4 connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the voltage of the Passenger Folding Mirror Relay Control circuit in the
relay connector.
Is the voltage above 1.0 volts?
All
Yes
→ Repair the Passenger Folding Mirror Relay Control circuit for a
short to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
1102
POWER MIRROR
Symptom:
UNFOLD MIRROR OUTPUT FAILURE (EXPORT ONLY)
POSSIBLE CAUSES
INTERMITTENT CONDITION
PASSENGER FOLDING MIRROR RELAY
LEFT POWER MIRROR
RIGHT POWER MIRROR
DRIVER FOLDING MIRROR FOLD DRIVER SHORT TO VOLTAGE
PASSENGER FOLDING MIRROR RELAY OUTPUT SHORT TO VOLTAGE
PASSENGER FOLDING MIRROR RELAY INPUT SHORT TO VOLTAGE
DRIVER FOLDING MIRROR FOLD DRIVER SHORT TO GROUND
PASSENGER FOLDING MIRROR RELAY OUTPUT SHORT TO GROUND
PASSENGER FOLDING MIRROR RELAY INPUT SHORT TO GROUND
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
NOTE: Doors must be closed to allow the mirrors to fold with the power folding
mirror switch.
Attempt to operate the power folding mirror system with the power folding mirror
switch and by opening and closing both front doors with mirrors folded.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 2
No
→ The condition that caused this DTC is currently not present. Use
the wiring diagram/schematic as a guide, and inspect the related
wiring harness for a possible intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.
2
Install a substitute relay in place of the Passenger Folding Mirror Relay.
With the DRBIII
t, erase DTC’s.
NOTE: Doors must be closed to allow the mirrors to fold with the power folding
mirror switch.
Attempt to operate the power folding mirror system with the power folding mirror
switch and by opening and closing both front doors with mirrors folded.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 3
No
→ Replace the Passenger Folding Mirror Relay.
Perform BODY VERIFICATION TEST - VER 1.
1103
POWER MIRROR
TEST
ACTION
APPLICABILITY
3
Disconnect the Left Power Mirror connector.
NOTE: Check connectors - Clean/repair as necessary.
With the DRBIII
t, erase DTC’s.
Operate the Power Folding Mirror switch.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 4
No
→ Replace the Left Power Mirror.
Perform BODY VERIFICATION TEST - VER 1.
4
Disconnect the Right Power Mirror connector.
NOTE: Check connectors - Clean/repair as necessary.
With the DRBIII
t, erase DTC’s.
Operate the Power Folding Mirror switch.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 5
No
→ Replace the Right Power Mirror.
Perform BODY VERIFICATION TEST - VER 1.
5
Disconnect the Left and Right Power Mirror connectors.
Disconnect the Body Control Module C2 connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure for unwanted voltage on the Driver Folding Mirror Fold Driver circuit in the
BCM C2 connector.
Is there any voltage present?
All
Yes
→ Repair the Driver Folding Mirror Fold Driver circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
Disconnect the Left and Right Power Mirror connectors.
Disconnect the Passenger Folding Mirror Relay.
NOTE: Check connectors - Clean/repair as necessary.
Measure for unwanted voltage on the Passenger Folding Mirror Relay Output circuit
in the relay connector.
Is there any voltage present?
All
Yes
→ Repair the Passenger Folding Mirror Relay Output circuit for a
short to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 7
7
Disconnect the Body Control Module C2 connector.
Disconnect the Passenger Folding Mirror Relay.
NOTE: Check connectors - Clean/repair as necessary.
Measure for unwanted voltage on the Passenger Folding Mirror Relay Input circuit
in the relay connector.
Is there any voltage present?
All
Yes
→ Repair the Passenger Folding Mirror Relay Input circuit for a
short to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 8
1104
POWER MIRROR
UNFOLD MIRROR OUTPUT FAILURE (EXPORT ONLY) —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст