Chrysler RG Voyager. Manual — part 282
Symptom:
*POWER SLIDING DOOR INOPERATIVE
POSSIBLE CAUSES
DTC’S PRESENT
MODULE RESPONSE
INTERMITTENT PROBLEM
SYSTEM TESTS
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t check for response from the Body Computer and the Power Sliding
Door Modules
Is there response from both modules?
All
Yes
→ Go To 2
No
→ Refer to symptom list for problems related to COMMUNICA-
TION.
2
With the DRBIII
t, read DTCs in POWER SLIDING DOOR and BODY COMPUTER.
Are any Power Sliding Door related codes present?
All
Yes
→ Refer to symptom list for problems related to POWER SLIDING
DOORS.
No
→ Go To 3
3
This test will determine what inhibited the Power Sliding Door from operating
properly.
With the DRBIII
t, select POWER SLIDING DOOR, MISCELLANEOUS, LAST
INHIBIT MONITOR.
Does the DRBIII
t display any INHIBIT REASONS?
All
Yes
→ Check for any binding conditions or other restrictions that may
prevent proper operation. Using the wiring diagram/schematic as
a guide, inspect the wiring and connectors.
No
→ Go To 4
4
Ensure the sliding door is fully closed before proceeding.
With the DRBIII
t select SYSTEM TEST.
Perform the Open, Close, Latch Cinch, Latch Release and Relay tests.
Did any test fail?
All
Yes
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors.
No
→ Test Complete.
1097
POWER DOORS - SLIDING
Symptom:
FOLD MIRROR OUTPUT FAILURE (EXPORT ONLY)
POSSIBLE CAUSES
INTERMITTENT CONDITION
LEFT POWER MIRROR
RIGHT POWER MIRROR
LEFT FOLDING MIRROR UNFOLD DRIVER SHORT TO VOLTAGE
RIGHT FOLDING MIRROR UNFOLD DRIVER SHORT TO VOLTAGE
LEFT FOLDING MIRROR UNFOLD DRIVER SHORT TO GROUND
RIGHT FOLDING MIRROR UNFOLD DRIVER SHORT TO GROUND
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
NOTE: Doors must be closed to allow the mirrors to fold with the power folding
mirror switch.
Attempt to operate the power folding mirror system with the power folding mirror
switch and by opening and closing both front doors with mirrors folded.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 2
No
→ The condition that caused this DTC is currently not present. Use
the wiring diagram/schematic as a guide, and inspect the related
wiring harness for a possible intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.
2
Disconnect the Left Power Mirror connector.
NOTE: Check connectors - Clean/repair as necessary.
With the DRBIII
t, erase DTC’s.
Operate the Power Folding Mirror switch.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 3
No
→ Replace the Left Power Mirror.
Perform BODY VERIFICATION TEST - VER 1.
3
Disconnect the Right Power Mirror connector.
NOTE: Check connectors - Clean/repair as necessary.
With the DRBIII
t, erase DTC’s.
Operate the Power Folding Mirror switch.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 4
No
→ Replace the Right Power Mirror.
Perform BODY VERIFICATION TEST - VER 1.
1098
POWER MIRROR
TEST
ACTION
APPLICABILITY
4
Disconnect the Left and Right Power Mirror connectors.
Disconnect the Body Control Module C2 connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure for unwanted voltage on the Left Folding Mirror Unfold Driver circuit in the
BCM C2 connector.
Is there any voltage present?
All
Yes
→ Repair the Left Folding Mirror Unfold Driver circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Disconnect the Left and Right Power Mirror connectors.
Disconnect the Body Control Module C2 connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure for unwanted voltage on the Right Folding Mirror Unfold Driver circuit in
the relay connector.
Is there any voltage present?
All
Yes
→ Repair the Right Folding Mirror Unfold Driver circuit for a short
to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
Disconnect the Left and Right Power Mirror connectors.
Disconnect the Body Control Module C2 connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Left Folding Mirror Unfold Driver
circuit in the BCM C2 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Left Folding Mirror Unfold Driver circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 7
7
Disconnect the Left and Right Power Mirror connectors.
Disconnect the Body Control Module C2 connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Right Folding Mirror Unfold Driver
circuit in the relay connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Right Folding Mirror Unfold Driver circuit for a short
to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
1099
POWER MIRROR
FOLD MIRROR OUTPUT FAILURE (EXPORT ONLY) —
Continued
Symptom:
PASSENGER MIRROR RELAY OUTPUT OPEN (EXPORT ONLY)
POSSIBLE CAUSES
INTERMITTENT CONDITION
FUSED B+ CIRCUIT OPEN
PASSENGER FOLDING MIRROR RELAY
PASSENGER FOLDING MIRROR RELAY CONTROL CIRCUIT SHORTED TO GROUND
PASSENGER FOLDING MIRROR RELAY CONTROL CIRCUIT OPEN
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
NOTE: Doors must be closed to allow the mirrors to fold with the power folding
mirror switch.
Attempt to operate the power folding mirror system with the power folding mirror
switch and by opening and closing both front doors with mirrors folded.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 2
No
→ The condition that caused this DTC is currently not present. Use
the wiring diagram/schematic as a guide, and inspect the related
wiring harness for a possible intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.
2
Disconnect the Passenger Folding Mirror Relay connector.
NOTE: Check connectors - Clean/repair as necessary.
Using a 12-volt test light connected to ground, check the Fused B+ circuit in the relay
connector.
The test light must illuminate brightly. Compare the brightness to that of a direct
connection to the battery.
Does the test light illuminate brightly?
All
Yes
→ Go To 3
No
→ Repair the Fused B+ circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
3
Remove the Passenger Folding Mirror Relay.
Check connectors - Clean/repair as necessary.
Install a substitute relay in place of the Passenger Folding Mirror Relay.
With the DRBIII
t, erase DTC’s.
NOTE: Doors must be closed to allow the mirrors to fold with the power folding
mirror switch.
Attempt to operate the power folding mirror system with the power folding mirror
switch and by opening and closing both front doors with mirrors folded.
With the DRBIII
t, read DTCs.
Does the same DTC reset?
All
Yes
→ Go To 4
No
→ Replace the Passenger Folding Mirror Relay.
Perform BODY VERIFICATION TEST - VER 1.
1100
POWER MIRROR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст