Chrysler RG Voyager. Manual — part 125
Symptom:
LEFT PSD MESSAGES NOT RECEIVED
When Monitored and Set Condition:
LEFT PSD MESSAGES NOT RECEIVED
When Monitored:
When the Body Control Module is awake.
Set Condition:
The BCM does not sense a response from the Left Power Sliding Door
Module.
POSSIBLE CAUSES
CHECK FOR DTCS
VERIFY DTC
ATTEMPT TO COMMUNICATE WITH THE LEFT SLIDING DOOR CONTROL MODULE
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, read BCM DTC’s.
Are any IOD Wakeup power sliding door DTC’s set?
All
Yes
→ Refer to symptom list for problems related to the IOD wakeup
circuit.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition on.
With the DRBIII
t, erase DTC’s.
Operate the left power sliding door with either the key fob or the overhead console.
With the DRBIII
t, read BCM DTC’s.
Did this DTC reset?
All
Yes
→ Go To 3
No
→ The condition that caused this DTC is currently not present. Use
the wiring diagrams/schematic as a guide, and inspect the related
wiring harness for a possible intermittent.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition on.
With the DRB, attempt to communicate with the Left Sliding Door Control Module.
Was the DRB able to I/D or communicate with the Left Sliding Door Control Module?
All
Yes
→ Go To 4
No
→ Refer to the Communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
469
COMMUNICATION
TEST
ACTION
APPLICABILITY
4
With the DRB, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
Operate the left power sliding door with either the key fob or the overhead console.
With the DRB, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Body Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
470
COMMUNICATION
LEFT PSD MESSAGES NOT RECEIVED —
Continued
Symptom:
LIFTGATE MODULE MESSAGES NOT RECEIVED
When Monitored and Set Condition:
LIFTGATE MODULE MESSAGES NOT RECEIVED
When Monitored:
When the Body Control Module is awake.
Set Condition:
The BCM does not sense a response from the Power Liftgate Control
Module.
POSSIBLE CAUSES
CHECK FOR DTCS
VERIFY DTC
ATTEMPT TO COMMUNICATE WITH THE POWER LIFTGATE MODULE
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, read BCM DTC’s.
Are any IOD Wakeup power liftgate DTC’s set?
All
Yes
→ Refer to symptom list for problems related to the IOD wakeup
circuit.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition on.
With the DRBIII
t, erase DTC’s.
Operate the liftgate with either the key fob or the overhead console.
With the DRBIII
t, read BCM DTC’s.
Did this DTC reset?
All
Yes
→ Go To 3
No
→ The condition that caused this DTC is currently not present. Use
the wiring diagrams/schematic as a guide, and inspect the related
wiring harness for a possible intermittent.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition on.
With the DRB, attempt to communicate with the Power Liftgate Module.
Was the DRB able to I/D or communicate with the Power Liftgate Module?
All
Yes
→ Go To 4
No
→ Refer to the Communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
471
COMMUNICATION
TEST
ACTION
APPLICABILITY
4
With the DRB, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
Operate the liftgate with either the key fob or the overhead console.
With the DRB, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Body Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
472
COMMUNICATION
LIFTGATE MODULE MESSAGES NOT RECEIVED —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст