Chrysler RG Voyager. Manual — part 248
Symptom:
INCOMPLETE LATCH CINCH - NO PAWL TRANSITION
When Monitored and Set Condition:
INCOMPLETE LATCH CINCH - NO PAWL TRANSITION
When Monitored:
Whenever the power liftgate in performing a cinching operation.
Set Condition:
The pawl switch was not detected as returning to ground during the
transition between secondary and primary cinch operation. NOTE: The liftgate may not be
fully cinched during this condition. The liftgate may cinch to primary but not be fully
seated and may pop off back to secondary.
POSSIBLE CAUSES
DTC PRESENT
BINDING LIFTGATE
GROUND WIRE OPEN
LIFTGATE PAWL SWITCH SENSE WIRE OPEN
LIFTGATE PAWL SWITCH SENSE WIRE SHORT TO GROUND
PAWL SWITCH
TEST
ACTION
APPLICABILITY
1
NOTE: This DTC will only set after the cinching operation. This may make
it difficult to reproduce.
With the DRBIII
t, record and erase DTC’s.
Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power liftgate several times if possible.
With the DRBIII
t, read ACTIVE DTCs.
Does the DRBIII
t display INCOMPLETE LATCH CINCH - NO PAWL TRANSI-
TION?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition. Operate the
door several times and check for any binding or other obstruc-
tions.
Perform BODY VERIFICATION TEST - VER 1.
2
Examine the liftgate for proper fit and alignment, lose/hard or torn seals, misaligned
latch striker or anything that would cause an obstruction to proper operation.
Manually operate the liftgate of a known good vehicle and notice the effort needed to
open and close.
Compare the effort needed on the disabled liftgate.
Does it take more effort to operate the liftgate than it should?
All
Yes
→ Refer to Service information for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
961
POWER DOORS - LIFTGATE
TEST
ACTION
APPLICABILITY
3
Disconnect the Power Liftgate C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance of the Ground wire between the PLG C2 connector (cavity 20)
and the Liftgate Cinch/Release Motor connector (cavity 1).
Wiggle the harness while observing the ohmmeter.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Ground wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
4
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance of the Liftgate Pawl Switch Sense wire between the PLG C2
connector and the Liftgate Cinch/Release Motor connector.
Wiggle the harness while observing the ohmmeter.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 5
No
→ Repair the Liftgate Pawl Switch Sense wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
5
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance between ground and the Liftgate Pawl Switch Sense circuit.
Wiggle the harness while observing the ohmmeter.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Liftgate Pawl Switch Sense wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
If there are no possible causes remaining, view repair.
All
Repair
Replace the Pawl Switch (latch assembly).
Perform BODY VERIFICATION TEST - VER 1.
962
POWER DOORS - LIFTGATE
INCOMPLETE LATCH CINCH - NO PAWL TRANSITION —
Continued
Symptom:
INCOMPLETE LATCH CINCH - OVERCURRENT
When Monitored and Set Condition:
INCOMPLETE LATCH CINCH - OVERCURRENT
When Monitored:
Whenever the power liftgate is performing a cinching operation.
Set Condition:
The latch motor stall current of 6.2 amps has been detected, with no pawl
or ratchet failure. This code is set during the first stage of the power cinching operation.
POSSIBLE CAUSES
DTC PRESENT
BINDING LIFTGATE
LIFTGATE LATCH CINCH DRIVER WIRE OPEN
LIFTGATE LATCH RELEASE DRIVER OPEN
LIFTGATE LATCH CINCH DRIVER WIRE SHORT TO GROUND
LIFTGATE LATCH CINCH DRIVER WIRE SHORT TO HARNESS GROUND
LIFTGATE LATCH RELEASE DRIVER WIRE SHORT TO GROUND
LIFTGATE LATCH RELEASE DRIVER WIRE SHORT TO HARNESS GROUND
LATCH ASSEMBLY
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power liftgate several times if possible.
With the DRBIII
t, read ACTIVE DTCs.
Does the DRBIII
t display INCOMPLETE LATCH CINCH - OVERCURRENT?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition. Operate the
liftgate several times and check for any binding or other obstruc-
tions.
Perform BODY VERIFICATION TEST - VER 1.
2
Examine the liftgate for proper alignment, worn or binding hinges, weak liftgate prop
assembly, loose/ hard weatherstrip, and gear teeth on the power liftgate motor
assembly for wear or anything that would cause an obstruction to proper operation.
If necessary manually operate the power liftgate on a known good vehicle and notice
the effort needed to open and close for comparison.
Especially notice the effort needed to unlatch and close the liftgate.
Were there any mechanical problems found?
All
Yes
→ Refer to Service information for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
963
POWER DOORS - LIFTGATE
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance of the Liftgate Latch Cinch Driver circuit between the Power
Liftgate Module C2 connector and the Liftgate Cinch/Release Motor connector.
Wiggle the harness and check for an intermittent open condition.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Liftgate Latch Cinch Driver wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
4
Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance of the Liftgate Latch Release Driver circuit between the
Power Liftgate Module C2 connector and the Liftgate Cinch/Release Motor connector.
Wiggle the harness and check for an intermittent open condition.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 5
No
→ Repair the Liftgate Latch Release Driver wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
5
Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance between ground and the Liftgate Latch Cinch Driver circuit.
Wiggle the harness and check for an intermittent short condition.
Is the resistance below 1000.0 ohms?
All
Yes
→ Go To 6
No
→ Repair the Liftgate Latch Cinch Driver wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
6
Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Liftgate Cinch/Release Motor connector.
Measure the resistance between the Ground circuit (cavity 20) and the Liftgate Latch
Cinch Driver circuit.
Wiggle the harness and check for an intermittent short condition.
Is the resistance below 1000.0 ohms?
All
Yes
→ Go To 7
No
→ Repair the Liftgate Latch Cinch Driver wire for a short to the
Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.
964
POWER DOORS - LIFTGATE
INCOMPLETE LATCH CINCH - OVERCURRENT —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст