Chrysler RG Voyager. Manual — part 1122
(1) Using a Hand, trim stick or equivalent, with
the mirror and frame outer edge pulled outward
carefully pry/pull outward and till the mirror glass
and frame comes loose (Fig. 31).
(2) Disconnect the heated mirror electrical connec-
tors from the terminals on the mirror glass holder, if
equipped (Fig. 32).
(3) Remove mirror glass and frame from vehicle.
INSTALLATION
WARNING: Always wear eye and hand protection
when servicing the mirror assembly. Failure to
observe these warnings may result in personal
injury from broken glass.
NOTE: The mirrors glass come in two types, type
one the mirror glass and frame has to be pried
upward to be removed, and type two the mirror
glass and frame has to be pulled (pried) outward.
To tell the difference one mirror glass and frame is
thicker than the other.
TYPE ONE
(1) Connect the mirror electrical connectors and
terminals on the mirror glass frame, if equipped (Fig.
33).
(2) Place mirror glass and frame into position in
the mirror assembly (Fig. 34).
(3) Align the mirror glass and frame locking tabs
to the mirror motor housing.
(4) Using a trim stick or equivalent, firmly press
the mirror glass and frame downward to lock into
place while at the same time supporting the housing
assembly from the backside with the other hand (Fig.
35).
(5) Verify retention of the mirror glass holder
assembly by gently pulling outward on the mirror
glass and frame.
Fig. 30 TYPE TWO MIRROR GLASS AND FRAME
THICKNESS
Fig. 31 REMOVING MIRROR GLASS
Fig. 32 REAR VIEW OF MIRROR GLASS
1 - MIRROR GLASS AND FRAME RETAINING CLIPS
2 - MIRROR AND FRAME ASSEMBLY
3 - MIRROR WIRE CONNECTORS AND TERMINALS
RS
EXTERIOR
23 - 67
GLASS-OUTSIDE REARVIEW MIRROR (Continued)
TYPE TWO
(1) Connect the mirror electrical connectors and
terminals on the mirror glass frame, if equipped (Fig.
36).
(2) Place mirror glass and frame into position in
the mirror assembly (Fig. 37).
(3) Align the mirror glass and frame locking tabs
to the mirror motor housing.
Fig. 33 MIRROR HOUSING - MEMORY MIRROR
1 - MIRROR MOTOR AND MOUNTING PLATE
2 - WIRE CONNECTORS
3 - LOCKING TABS
Fig. 34 REAR VIEW OF MEMORY MIRROR GLASS
1 - MIRROR GLASS AND FRAME LOCKING TAB RECEIVER
2 - MIRROR GLASS AND FRAME ASSEMBLY
3 - MIRROR WIRE CONNECTORS AND TERMINALS
Fig. 35 INSTALLING MEMORY MIRROR GLASS
Fig. 36 MIRROR HOUSING
1 - MIRROR MOTOR AND MOUNTING PLATE
2 - ALIGNMENT TABS
23 - 68
EXTERIOR
RS
GLASS-OUTSIDE REARVIEW MIRROR (Continued)
NOTE: Pressure must be applied equally over the
center portion of the mirror to engage the mirror
glass holder’s attaching fingers to the correspond-
ing fingers on the housing assembly. One or more
clicks may be heard when finger engagement takes
place.
(4) Press firmly onto the mirror glass and frame to
lock into place while at the same time supporting the
housing assembly from the backside with the other
hand (Fig. 38).
(5) Verify retention of the mirror glass holder
assembly by gently pulling outward on the mirror
glass and frame.
Fig. 37 REAR VIEW OF MIRROR GLASS
1 - MIRROR GLASS AND FRAME RETAINING CLIPS
2 - MIRROR AND FRAME ASSEMBLY
3 - MIRROR WIRE CONNECTORS AND TERMINALS
Fig. 38 INSTALLING MIRROR GLASS
RS
EXTERIOR
23 - 69
GLASS-OUTSIDE REARVIEW MIRROR (Continued)
HOOD
TABLE OF CONTENTS
page
page
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
. . . . . . . . . . . . . . . . . . . . . . . . . 70
HOOD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
. . . . . . . . . . . . . . . . . . . . . . . . . 70
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
. . . . . . . . . . . . . . . . . . . . . . . . . 71
LATCH RELEASE CABLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
. . . . . . . . . . . . . . . . . . . . . . . . . 72
LATCH STRIKER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
. . . . . . . . . . . . . . . . . . . . . . . . . 72
HINGE
REMOVAL
(1) Remove Front Wiper Unit (Refer to 8 - ELEC-
TRICAL/WIPERS/WASHERS/WIPER
MODULE
-
REMOVAL) for procedure.
(2) Raise hood.
(3) Mark all bolt and hinge attachment locations
with a grease pencil or other suitable device to pro-
vide reference marks for installation.
(4) Remove pivot bolt from the body half of hood
hinge and use suitable device to support the hood.
(5) Remove bolts attaching body half of hood hinge
to front fender flange and remove hinge from vehicle
(Fig. 1).
INSTALLATION
(1) If necessary, paint new hinge before installa-
tion.
(2) Place body half of hood hinge in position on
vehicle.
(3) Install bolts attaching hood hinge to front
fender flange. Tighten bolts to 8 N·m (70 in. lbs.)
torque.
(4) Install pivot bolt to the body half of hood hinge.
Tighten bolts to 28 N·m (21 ft. lbs.) torque.
(5) Install Front Wiper Unit (Refer to 8 - ELEC-
TRICAL/WIPERS/WASHERS/WIPER
MODULE
-
INSTALLATION) for proper procedures.
(6) Align all marks and secure bolts. The hood
should be aligned to 4 mm (0.160 in.) gap to the front
fenders and flush across the top surfaces along fend-
ers. Shims can be added or removed under hood
hinge to achieve proper hood height. Tighten bolts to
13.5 N·m (10 ft. lbs.) torque.Close hood.
HOOD
REMOVAL
(1) Raise hood to full up position.
(2) Mark all bolt and hinge attachment locations
with a grease pencil or other suitable device to pro-
vide reference marks for installation.
(3) Remove the top bolts attaching hood to hinge
and loosen the bottom bolts until they can be
removed by hand (Fig. 2).
(4) With assistance from a helper at the opposite
side of the vehicle to support the hood, remove bot-
tom bolts attaching hood to hinge.
(5) Remove the hood from the vehicle.
INSTALLATION
(1) Place hood in position on vehicle. With assis-
tance from a helper at the opposite side of the vehicle
Fig. 1 HOOD HINGE
1 - HOOD
2 - HOOD HALF OF HOOD HINGE
3 - HOOD HINGE PIVOT BUSHING
4 - BODY HALF OF HOOD HINGE
5 - FENDER
23 - 70
HOOD
RS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст