Chrysler RG Voyager. Manual — part 285
TEST
ACTION
APPLICABILITY
4
Disconnect the inoperative Power Mirror connector.
Disconnect the Body Control Module C2 connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the Driver Folding Mirror Fold Driver circuit from the BCM C2 connector
to the mirror harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the Driver Folding Mirror Fold Driver circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
1109
POWER MIRROR
*DRIVER FOLDING MIRROR DOES NOT FOLD (EXPORT ONLY) —
Continued
Symptom:
*PASSENGER FOLDING MIRROR DOES NOT FOLD (EXPORT
ONLY)
POSSIBLE CAUSES
RELATED DIAGNOSTIC TROUBLE CODES
PASSENGER FOLDING MIRROR RELAY
POWER MIRROR
FOLDING MIRROR UNFOLD DRIVER CIRCUIT OPEN
PASSENGER FOLDING MIRROR RELAY OUTPUT CIRCUIT OPEN
PASSENGER FOLDING MIRROR RELAY INPUT CIRCUIT OPEN
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, read Body Computer DTCs.
Does the DRBIII
t display any related DTC’s?
All
Yes
→ Refer to symptom list for problems related to Power Folding
Mirrors.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Disconnect the Passenger Folding Mirror Relay.
Check connectors - Clean/repair as necessary.
Connect a substitute relay in place of the Passenger Folding Mirror Relay.
NOTE: Doors must be closed to allow the mirrors to fold with the power folding
mirror switch.
Attempt to operate the power folding mirror system with the power folding mirror
switch and by opening and closing both front doors with mirrors folded.
Does the system now operate properly?
All
Yes
→ Replace the Passenger Folding Mirror Relay.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Connect Passenger Folding Mirror Relay if disconnected in previous step.
Disconnect the inoperative Power Mirror connector.
NOTE: Check connectors - Clean/repair as necessary.
Connect one lead of a test light to the Passenger Folding Mirror Relay Output circuit
and the other lead to the appropriate Folding Mirror Unfold Driver in the power
mirror harness connector.
With the DRBIII
t, actuate the Folding Mirrors.
Does the test light illuminate brightly?
All
Yes
→ Replace the appropriate Power Mirror.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
1110
POWER MIRROR
TEST
ACTION
APPLICABILITY
4
Disconnect the inoperative Power Mirror connector.
Disconnect the Body Control Module C2 connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the appropriate Folding Mirror Unfold Driver circuit from the BCM C2
connector to the power mirror harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 5
No
→ Repair the appropriate Folding Mirror Unfold Driver circuit for
an open.
Perform BODY VERIFICATION TEST - VER 1.
5
Disconnect the inoperative Power Mirror connector.
Disconnect the Passenger Folding Mirror Relay.
NOTE: Check connectors - Clean/repair as necessary.
Measure the Passenger Folding Mirror Relay Output circuit from the relay connector
to the mirror harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 6
No
→ Repair the Passenger Folding Mirror Relay Output circuit for an
open.
Perform BODY VERIFICATION TEST - VER 1.
6
Disconnect the Body Control Module C2 connector.
Disconnect the Passenger Folding Mirror Relay.
NOTE: Check connectors - Clean/repair as necessary.
Measure the Passenger Folding Mirror Relay Input circuit from the relay connector
to the BCM C2 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the Passenger Folding Mirror Relay Input circuit for an
open.
Perform BODY VERIFICATION TEST - VER 1.
1111
POWER MIRROR
*PASSENGER FOLDING MIRROR DOES NOT FOLD (EXPORT ONLY) —
Continued
Symptom:
AMP MESSAGE NOT RECEIVED
When Monitored and Set Condition:
AMP MESSAGE NOT RECEIVED
When Monitored:
With the ignition on.
Set Condition:
The Hands Free Module does not receive a message from the amplifier.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE AMPLIFIER
MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
Turn the Radio on.
With the DRBIII
t, attempt to communicate with the Amplifier.
Was the DRBIII
t able to I/D or communicate with the Amplifier?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
2
With the DRBIII
t, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRBIII
t, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace and program the Hands Free Module in accordance with
the service information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
1112
TELECOMMUNICATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст