Chrysler Le Baron, Dodge Dynasty, Plymouth Acclaim. Manual — part 339
TAIL, STOP, TURN SIGNAL BULB OR LAMP
REMOVAL (FIG. 3)
(1) Open deck lid and remove the plastic wing nut
securing the rear trim cover in place.
(2) Pivot the end of the trim panel out of the way
to gain access, and remove three plastic wing-nuts
securing the lamp to the vehicle.
(3) Separate the tail lamp from the body far
enough to rotate the socket and bulb assemblies
counterclockwise one-half turn and pull the sockets
out of the lamp body.
(4) Remove the bulb from socket.
INSTALLATION
Reverse the preceding operation.
TRUNK LID TAIL LAMP BULB
REMOVAL (FIG. 3)
(1) Remove deck lid liner as necessary. Through
access hole in the inner deck lid, rotate socket coun-
terclockwise one-half turn, and pull the socket and
bulb assembly from the lamp body.
(2) Remove the bulb from the socket.
INSTALLATION
Reverse the preceding operation.
TRUNK LID TAIL LAMP
REMOVAL (FIG. 3)
(1) Remove bulb and sockets from trunk lid tail
lamp.
(2) Remove six nuts and four screws securing the
tail lamp to the deck lid and remove the lamp assem-
bly from the vehicle.
INSTALLATION
Reverse the preceding operation.
BACK-UP LAMP BULB
REMOVAL (FIG. 3)
(1) From behind the rear bumper fascia, rotate the
bulb and socket assembly counterclockwise one-half
turn and pull the bulb and socket out of the lamp body.
(2) Remove the bulb from the socket.
INSTALLATION
Reverse the preceding operation.
BACK-UP LAMP
REMOVAL (FIG. 3)
(1) Remove the socket and bulb assembly from the
lamp body.
(2) Remove two screws from the lamp and pull the
lamp from the rear bumper fascia.
INSTALLATION
Reverse the preceding operation.
REAR SIDE MARKER LAMP BULB
REMOVAL (FIG. 3)
(1) Open the deck lid and remove the fastener
(wing nut) from the lower rear trim panel. Rotate the
inner quarter trim panel forward to gain access to
the lamp assembly. Rotate counterclockwise one-half
turn, and pull the socket and bulb from the lamp
body.
(2) Remove the bulb from the socket.
INSTALLATION
Reverse the preceding operation.
REAR SIDE MARKER LAMP
REMOVAL (FIG. 3)
(1) Remove the socket and bulb assembly.
(2) Remove two attaching nuts from the lamp be-
hind the quarter panel and remove the lamp from
the vehicle.
INSTALLATION
Reverse the preceding operation.
LICENSE PLATE LAMP OR BULB
REMOVAL (FIG. 3)
(1) Remove screws holding license plate lamp to
rear bumper fascia.
Fig. 2 Park, Turn Signal, Cornering and Side Marker
Lamp—Typical
Fig. 3 Tail, Stop, Turn Signal, Back-Up, License
Plate and Side Marker Lamps
Ä
LAMPS
8L - 17
(2) Remove socket from back of lamp.
(3) Pull bulb from socket if bulb replacement is re-
quired.
(4) Separate lamp from vehicle.
INSTALLATION
Reverse the preceding operation.
CENTER HIGH MOUNTED STOP LAMP (CHMSL)
BULB
REMOVAL—AJ-BODY (FIG. 4)
(1) Open deck lid.
(2) From under the parcel shelf, rotate socket
counterclockwise, and pull the CHMSL socket and
bulb from the lamp. Remove the bulb from the
socket.
INSTALLATION
Reverse the preceding operation.
REMOVAL—AJ/27-BODY (FIG. 5)
(1) Remove CHMSL lens attaching screws and sep-
arate lens from the lamp body.
(2) Remove socket from lamp.
(3) Remove bulb.
INSTALLATION
Reverse the preceding operation.
CENTER HIGH-MOUNTED STOP LAMP ASSEMBLY
(CHMSL)
REMOVAL—AJ-BODY (FIG. 4)
(1) Remove parcel shelf trim cover. Refer to Group
23, Body.
(2) Remove two CHMSL attaching screws and sep-
arate the lamp from the parcel shelf.
INSTALLATION
Reverse the preceding operation.
REMOVAL—AJ/27-BODY (FIG. 5)
(1) From inside the luggage compartment, locate
and remove the two plastic plugs from under the
filler panel behind the compartment opening.
(2) Remove
the
two
CHMSL
attaching
nuts
through the clearance holes under the filler panel.
(3) Disconnect the wire connector and separate the
lamp assembly from the filler panel.
INSTALLATION
Reverse the preceding operation.
Fig. 4 Center High Mounted Stop Lamp—AJ-Body
Fig. 5 Center High Mounted Stop Lamp—AJ/27-Body
8L - 18
LAMPS
Ä
EXTERIOR LAMPS—AP BODY
INDEX
page
page
Center High Mounted Stop Lamp (CHMSL)—
. . . . . . . . . . . . . . . . . . . . . . . . . 21
Center High Mounted Stop Lamp Bulb—
. . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Front Side Marker Lamp or Bulb
. . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . 20
Park and Turn Signal Lamp or Bulb
Tail, Stop, Turn Signal, Back-Up and Side Marker
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Tail, Stop, Turn Signal, Back-Up and Side Marker
. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
HEADLAMP DIAGNOSIS
For headlamp diagnosis, refer to the headlamp di-
agnosis chart at the beginning of this group. Refer to
Wiring Diagrams manual for circuit and component
locations.
HEADLAMP BULB
REMOVAL (FIG. 1)
(1) Left front bulb removal: Remove the windshield
washer reservoir upper mounting screw and position
reservoir rearward.
(2) Disconnect wire connector from back of head-
lamp behind radiator closure panel.
CAUTION: Do not touch the bulb glass with fingers
or other oily surface, reduced bulb life will result.
(3) Rotate the bulb retaining ring counterclockwise
one quarter turn and remove the ring, bulb holder
and bulb from the lens assembly. The bulb holder
has alignment notches.
INSTALLATION
Reverse the preceding operation.
HEADLAMP HOUSING
RIGHT HEADLAMP REMOVAL (FIG. 1)
To remove the aero headlamp housing, perform
steps 1, 2 and 3 of bulb removal operation and pro-
ceed with the following steps.
(1) From in the engine compartment, remove the
three headlamp assembly to body attaching nuts and
separate the lamp from the body.
(2) Pull headlamp/lens assembly forward.
(3) Pull the lower section of the headlamp adjuster
cable from the lamp
adjuster screw.
(4) Remove headlamp/lens assembly.
(5) Remove the four lamp/lens to headlamp bucket
screws.
(6) Remove headlamp/lens.
INSTALLATION
Reverse the preceding operation.
LEFT HEADLAMP REMOVAL (FIG. 1)
(1) Disconnect battery cables, negative first, and
remove battery.
(2) Remove the windshield washer reservoir upper
mounting screw and position reservoir rearward.
(3) Remove the air cleaner intake tube.
(4) Remove screws holding Engine Controller to in-
ner fender flange.
(5) Move Engine Controller rearward, leave wires
connected.
(6) Remove air duct from front of Engine Control-
ler.
(7) Disconnect wire connector from back of head-
lamp.
(8) From in the engine compartment, remove nuts
holding headlamp housing to radiator closure panel.
(9) Separate headlamp housing from radiator clo-
sure panel.
(10) Pull headlamp housing forward.
(11) Pull the lower section of the headlamp ad-
juster cable from the lamp adjuster screw.
(12) Separate headlamp from vehicle.
INSTALLATION
Reverse the preceding operation.
Fig. 1 Aero Headlamp
Ä
LAMPS
8L - 19
PARK AND TURN SIGNAL LAMP OR BULB
REMOVAL (FIG. 2)
(1) Remove screws holding the park and turn sig-
nal lamp to the bumper facia.
(2) Separate lamp from bumper fascia.
(3) Rotate the socket counterclockwise and remove
the socket from the lamp assembly.
(4) Pull the bulb from the socket.
INSTALLATION
Reverse the preceding operation.
FRONT SIDE MARKER LAMP OR BULB
REMOVAL (FIG. 2)
(1) Locate
back
of
side
marker
lamp
behind
bumper fascia.
(2) Rotate socket counterclockwise and remove the
socket and bulb from the lamp.
(3) Pull bulb from socket if replacement is re-
quired.
(4) Remove nuts holding side marker lamp to the
fascia and separate lamp from vehicle.
INSTALLATION
Reverse the preceding operation.
TAIL, STOP, TURN SIGNAL, BACK-UP AND SIDE
MARKER LAMP BULBS
REMOVAL (FIG. 3)
(1) Remove luggage compartment rear trim cover.
(2) Loosen and shift the quarter panel silencer out
of the way.
(3) Rotate socket counterclockwise and separate
socket and bulb from lamp assembly.
(4) Remove the bulb from the socket.
INSTALLATION
Reverse the preceding operation.
TAIL, STOP, TURN SIGNAL, BACK-UP AND SIDE
MARKER LAMP
REMOVAL (FIG. 3)
(1) Remove luggage compartment rear trim cover.
(2) Loosen and shift the quarter panel silencer out
of the way.
(3) Rotate sockets counterclockwise and separate
sockets from lamp assembly.
(4) Remove the lamp assembly to body retaining
nuts.
(5) Remove the lamp assembly.
INSTALLATION
Reverse the preceding operation.
LICENSE PLATE LAMP OR BULB
REMOVAL (FIG. 4)
(1) Locate and remove two attaching screws hold-
ing the assembly to the tail panel.
(2) Separate the lens from the lamp assembly.
(3) Remove bulb from socket assembly.
INSTALLATION
Reverse the preceding operation.
Fig. 2 Park, Turn Signal, and Side Marker Lamps
Fig. 3 Tail, Stop, Turn Signal, Side Marker and
Back-Up Lamps
Fig. 4 License Plate Lamp—Typical
8L - 20
LAMPS
Ä
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст