Chrysler Le Baron, Dodge Dynasty, Plymouth Acclaim. Manual — part 340
CENTER HIGH MOUNTED STOP LAMP BULB—AP/
24-44-BODY
REMOVAL (FIG. 5)
(1) Remove the lower rear glass trim cover. Refer
to Group 23, Body.
(2) Rotate lamp sockets counterclockwise and re-
move them from the lamp assembly.
(3) Remove bulb from the socket.
INSTALLATION
Reverse the preceding operation.
CENTER HIGH MOUNTED STOP LAMP
(CHMSL)—AP/24-44-BODY
REMOVAL (FIG. 5)
(1) Remove the lower rear glass trim cover. Refer
to Group 23, Body.
(2) Remove two attaching nuts from the assembly
mounting and lift the lamp from the bracket.
(3) Remove bulbs from lamp.
(4) Remove lamp attaching nuts.
(5) Remove lamp assembly.
INSTALLATION
Reverse the preceding operation.
FOG LAMP BULB
REMOVAL
(1) From behind the front bumper support, rotate
the socket
counterclockwise one quarter turn, and remove the
socket from lamp assembly.
(2) Disconnect wire connector and remove bulb.
INSTALLATION
Reverse the preceding operation.
FOG LAMPS
REMOVAL (FIG. 6)
(1) Disconnect wire connector from back of lamp.
(2) Remove nut holding fog lamp to mounting
bracket.
(3) Separate fog lamp from bumper fascia.
Fig. 5 Center High Mounted Stop Lamp—AP/24-44-
Body
Fig. 6 Fog Lamps
Ä
LAMPS
8L - 21
EXTERIOR LAMPS—AY-BODY
INDEX
page
page
Center High Mounted Stop Lamp Bulb (CHMSL)
Cornering Lamp or Bulb—AY/C-P-Body
Front Side Marker Bulb—AY/C-P-Body
Front Side Marker Lamp—AY/C-P-Body
. . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
License Plate Lamp or Bulb—AY/C-P-Body
Park, Turn Signal Lamp or Bulb—AY/C-P-Body
. . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Tail, Stop, Turn Signal, Side Marker and Back-Up
. . . . . . . . . . . . . . 24
GENERAL INFORMATION
To service exterior lamps on AY/C-S-Body, refer to
procedures covered in Exterior Lamps—AC-Body sec-
tion. AC/C-S-Body uses the same lamps as AY/C-S-
Body.
HEADLAMPS
Conventional and halogen sealed beams are inter-
changeable, It is not recommended that they be
mixed. The lens, filament and reflector of sealed
beams are molded into one unit.
HEADLAMP DIAGNOSIS
For headlamp diagnosis, refer to the headlamp di-
agnosis chart at the beginning of this Group. Refer to
Wiring Diagrams manual for circuit and component
locations.
SEALED BEAM
REMOVAL
(1) Turn the headlight switch ON.
(2) Open the hood and locate the power distribu-
tion center forward of the left front suspension tower
(Fig. 1). Remove the cover.
(3) Remove the headlamp close relay (Fig. 2) to
prevent the headlamp doors from closing.
(4) Turn the headlight switch OFF.
(5) Remove screws from headlamp bezel and re-
move bezel, if equipped.
Do not disturb the headlamp adjusting screws.
(6) Remove screws from interior retaining ring
(Fig. 3), and remove ring.
(7) Separate sealed beam from seat and disconnect
wire connector.
INSTALLATION
Reverse the preceding operation.
PARK, TURN SIGNAL LAMP OR BULB—AY/C-P-
BODY
REMOVAL
(1) Open the headlamp doors.
(2) Remove push-in fasteners holding lower park
and turn signal lamp shield to grille opening panel
(Fig. 4).
(3) Remove screws holding park and turn signal
lamp grille opening panel (Fig. 5).
(4) Remove sockets from lamp and pull bulbs from
sockets if bulbs replacement is required (Fig. 6).
Fig. 1 Power Distribution Center
Fig. 2 Headlamp Close Relay
8L - 22
LAMPS
Ä
INSTALLATION
Reverse the preceding operation.
FRONT SIDE MARKER BULB—AY/C-P-BODY
REMOVAL
(1) Raise vehicle.
(2) Reach over the top of cornering lamp (Fig. 7)
and remove bulb/socket (Fig. 8).
INSTALLATION
Reverse the preceding operation.
FRONT SIDE MARKER LAMP—AY/C-P-BODY
REMOVAL (FIG. 7)
(1) Remove the cornering lamp retaining nuts, and
remove cornering lamp.
(2) Remove the four nuts retaining the bumper
trim moulding to the body.
(3) Remove bumper trim moulding.
(4) Remove side marker lamp.
INSTALLATION
Reverse the preceding operation.
Fig. 3 Sealed Beam Replacement—Typical
Fig. 4 Turn Signal Lamp Shield
Fig. 5 Turn Signal Lamp Mounting Screws
Fig. 6 Turn Signal Lamp
Fig. 7 Bumper Trim Moulding Nuts—AY/C-P-Body
Ä
LAMPS
8L - 23
CORNERING LAMP OR BULB—AY/C-P-BODY
REMOVAL (FIG. 8)
(1) Raise vehicle.
(2) Remove bulb.
(3) To remove lamp assembly, remove the two re-
taining nuts.
INSTALLATION
Reverse the preceding operation.
TAIL, STOP, TURN SIGNAL, SIDE MARKER AND
BACK-UP LAMP OR BULB—AY/C-P-BODY
REMOVAL (FIG. 9)
(1) Open the trunk lid and remove the tail panel
trim cover attaching screws and position the trim
cover away from the tail panel.
(2) Disconnect rear end lamp wire connector and
push the harness grommet outward through the tail
panel.
(3) Remove rear lamp assembly attaching screws
and separate the lamp assembly from the body.
(4) Remove bulbs from lamp assembly.
INSTALLATION
Reverse the preceding operation.
LICENSE PLATE LAMP OR BULB—AY/C-P-BODY
REMOVAL
(1) Remove the two screws retaining the lamp to
the bumper guard.
(2) Remove the bulb from the socket assembly.
INSTALLATION
Reverse the preceding operation.
CENTER HIGH MOUNTED STOP LAMP BULB
(CHMSL)
REMOVAL AND INSTALLATION
(1) Open deck lid.
(2) From under the parcel shelf, rotate socket
counterclockwise, and pull the CHMSL socket and
bulb from the lamp.
(3) Pull bulb from the socket.
INSTALLATION
Reverse the preceding operation.
CENTER HIGH MOUNTED STOP LAMP
REMOVAL (FIG. 10)
(1) Remove parcel shelf trim cover. Refer to Group
23, Body.
(2) Remove two CHMSL attaching screws and sep-
arate the lamp from the parcel shelf.
INSTALLATION
Reverse the preceding operation.
Fig. 8 Cornering Lamp—AY/C-P-Body
Fig. 9 Rear End Lighting—AY/C-P-Body
Fig. 10 Center High Mounted Stop Lamp—Typical
8L - 24
LAMPS
Ä
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст