Chrysler Pacifica. Manual — part 832
WARNING:
TO
AVOID
PERSONAL
INJURY
OR
DEATH ON VEHICLES EQUIPPED WITH THE OCCU-
PANT CLASSIFICATION SYSTEM (OCS), ONLY THE
OCCUPANT CLASSIFICATION MODULE (OCM) AND
THE SEAT CUSHION TRIM MAY BE SERVICED SEP-
ARATELY. ALL OTHER COMPONENTS OF THE PAS-
SENGER SIDE FRONT SEAT CUSHION ASSEMBLY
MUST BE SERVICED ONLY AS A COMPLETE FAC-
TORY-CALIBRATED, ASSEMBLED AND TAMPER-EV-
IDENT SERVICE REPLACEMENT PACKAGE. THIS
PACKAGE INCLUDES THE FRAME, SPRINGS, PAD,
BLADDER, SENSOR, FOAM, WIRING AND A CALI-
BRATED OCM. WHEN INSTALLING THIS PACKAGE
ALWAYS REPLACE ALL OF THE EXISTING COMPO-
NENTS WITH THE NEW COMPONENTS AS A UNIT.
DO NOT ATTEMPT TO SEPARATE OR DISCONNECT
ANY OF THE NEW OCS COMPONENTS IN THE SER-
VICE
REPLACEMENT
PACKAGE
FROM
EACH
OTHER, AND DO NOT ATTEMPT TO REUSE ANY OF
THE REPLACED COMPONENTS IN THIS OR ANY
OTHER VEHICLE. FAILURE TO TAKE THE PROPER
PRECAUTIONS COULD RESULT IN FAILURE OF
THE PASSENGER AIRBAG TO DEPLOY WHEN
REQUIRED, OR IN PASSENGER AIRBAG DEPLOY-
MENT WHEN NOT REQUIRED.
(1) Position seat cushion foam and seat cover
together (Fig. 9).
(2) Place seat cushion foam/cover onto seat pan.
(3) Engage seat cushion cover J-straps and push
pins attaching to seat pan (Fig. 8).
(4) Install front seat back to seat assembly. (Refer
to
23
-
BODY/SEATS/FRONT
SEAT
BACK
-
INSTALLATION).
(5) Install front seat. (Refer to 23 - BODY/SEATS/
FRONT SEAT - INSTALLATION).
FRONT SEAT BACK PANEL
REMOVAL
(1) Using a trim tool C-4755 or equivalent, disen-
gage the front seat (Fig. 10) and (Fig. 11).
Fig. 10 FRONT SEAT BACK PANEL
1 - PRY SEAT COVER PANEL OUTWARD AND DOWN TO
RELEASE HOOKS.
Fig. 11 TOP HOOK
1 - TOP HOOKS EXPOSED
CS
SEATS
23 - 123
FRONT SEAT CUSHION FOAM / COVER (Continued)
(2) Pushing the top edge of back panel outward
and pushing upward that the same time till lower
hooks are clear of the lower metal bracket (Fig. 12).
(3) Gently rotate the seat back panel clockwise
until upper left hook and lower right hook disengage
from trim ring (Fig. 13).
(4) Gently rotate the seat back panel counter
clockwise until upper right hook and lower left hook
disengage from trim ring and remove front seat back
panel for seat back (Fig. 14).
INSTALLATION
(1) Place front seat back panel into position and
start lower hooks.
(2) Push on front seat back panel to engage lock-
ing clips.
(3) Grasp the top of the seat back panel and push
downward to engage the top hooks.
Fig. 12 RELEASE LOWER HOOKS
1 - PUSHING OUTWARD AND UPWARD
Fig. 13 ROTATE SEAT BACK PANEL CLOCKWISE
1 - ROTATE CLOCKWISE
Fig. 14 ROTATE SEAT BACK PANEL COUNTER
CLOCKWISE
1 - ROTATE COUNTER CLOCKWISE
23 - 124
SEATS
CS
FRONT SEAT BACK PANEL (Continued)
FRONT SEAT OUTER TRIM
RING PANEL
REMOVAL
(1) Remove front seat inner panel. (Refer to 23 -
BODY/SEATS/FRONT
SEAT
INNER
PANEL
-
REMOVAL).
(2) Remove front seat outer trim ring panel four
attaching screws, if equipped (Fig. 15).
(3) Remove outer trim ring panel from rear of seat.
INSTALLATION
(1) Place seat outer trim ring panel into position
on rear of seat.
(2) Install seat outer trim ring panel four attach-
ing screws, if equipped (Fig. 15).
(3) Install front seat inner panel. (Refer to 23 -
BODY/SEATS/FRONT
SEAT
INNER
PANEL
-
INSTALLATION).
FRONT SEAT SHIELDS
REMOVAL
The front seat shield positions and attachment
points (Fig. 16).
UPPER ADJUSTER INBOARD AND REAR SHIELD
(1) Remove
upper
adjuster
inboard
attaching
screw (Fig. 16).
(2) Pull rear edge away from upper adjuster
inboard rear shield to release locking tab.
(3) Remove upper adjuster inboard rear shield
attaching screw and remove shield.
FRONT SHIELD
(1) Remove front shield attaching screws (Fig. 17).
(2) Pull forward on front shield edge by the upper
adjuster outboard shield to disengage locking tabs
(Fig. 16) and (Fig. 18).
(3) Remove front shield.
UPPER ADJUSTER OUTBOARD AND REAR SHIELD
(1) Remove front attaching screw (Fig. 16).
Fig. 15 FRONT SEAT OUTER TRIM RING PANEL
Fig. 16 FRONT SEAT SHIELDS
1 - UPPER ADJUSTER INBOARD SHIELD
2 - UPPER ADJUSTER INBOARD REAR SHIELD
3 - UPPER ADJUSTER OUTBOARD REAR SHIELD
4 - UPPER ADJUSTER OUTBOARD SHIELD
5 - LOWER RISER OUTBOARD SHIELD
6 - LOCKING TABS
7 - FRONT SHIELD
Fig. 17 FRONT SEAT FRONT SHIELD
1 - ATTACHING SCREWS
CS
SEATS
23 - 125
(2) Pull rear edge away from upper adjuster out-
board rear shield to release locking tab.
(3) Remove upper adjuster outboard rear shield
attaching screw and remove shield.
LOWER RISER SHIELD
(1) Remove front and rear attaching screws (Fig.
16).
(2) Remove lower riser shield.
INSTALLATION
UPPER ADJUSTER INBOARD AND REAR SHIELD
(1) Place upper adjuster inboard rear shield into
position and install attaching screw (Fig. 16).
(2) Press on rear edge upper adjuster inboard
shield locking tabs to upper adjuster inboard rear
shield to engage locking tabs.
(3) Install upper adjuster inboard attaching screw.
FRONT SHIELD
(1) Place front shield in position.
(2) Press on front shield edge by the upper
adjuster outboard shield to engage locking tabs (Fig.
16) and (Fig. 18).
(3) Install front shield attaching screws (Fig. 17).
UPPER ADJUSTER OUTBOARD AND REAR SHIELD
(1) Place upper adjuster outboard rear shield into
position and install attaching screw (Fig. 16) and
(Fig. 19).
(2) Place upper adjuster outboard shield into posi-
tion.
(3) Press on rear edge upper adjuster outboard
shield locking tabs to upper adjuster outboard rear
shield to engage locking tabs.
(4) Install front attaching screw.
LOWER RISER SHIELD
(1) Place lower riser shield into position (Fig. 16).
(2) Install front and rear attaching screws.
HEADREST
REMOVAL
(1) Lift head restraint to top of travel.
(2) Depress locking button on side of sleeve at top
of seat back (Fig. 20).
(3) Pull head restraint from top of seat back.
Fig. 18 FRONT SEAT FRONT SHIELD LOCKING
TABS
1 - UPPER ADJUSTER OUTBOARD SHIELD
2 - FRONT SHIELD
Fig. 19 UPPER ADJUSTER OUTBOARD REAR
SHIELD
1 - UPPER ADJUSTER OUTBOARD SHIELD
2 - ATTACHING SCREW
3 - UPPER ADJUSTER OUTBOARD REAR SHIELD
Fig. 20 HEADREST AND SLEEVES
1 - HEADREST
2 - NON-LOCKING SLEEVE
3 - LOCKING SLEEVE
23 - 126
SEATS
CS
FRONT SEAT SHIELDS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст