Chrysler Pacifica. Manual — part 833
(4) Using trim tool, remove headrest sleeve(s) (Fig.
21).
INSTALLATION
(1) Place headrest sleeve(s) into position.
(2) Press down on headrest sleeve to lock into posi-
tion.
(3) Place head restraint in position (Fig. 20).
(4) Depress lock button on side of sleeve at top of
seat back.
(5) Push heat restraint down into position.
RECLINER HANDLE
REMOVAL
(1) Remove
screw
holding
recliner
handle
to
recliner spline shaft (Fig. 22).
(2) Remove recliner handle from spline shaft.
INSTALLATION
(1) Place recliner handle in position on spline
shaft.
(2) Install screw to hold recliner handle to recliner
spline shaft (Fig. 22).
SEAT ARMREST
REMOVAL
(1) Using a small flat blade, pry cap from side of
armrest (Fig. 23).
(2) Remove bolt attaching armrest to seat back.
(3) Remove armrest from seat back.
INSTALLATION
(1) Place armrest in position on seat back.
(2) Install bolt attaching armrest to seat back.
Tighten bolt to 29 N·m (21 ft. lbs.) torque.
(3) Install side cap into the side of the armrest.
Fig. 21 REMOVING HEADREST SLEEVE
1 - TRIM TOOL
2 - HEADREST SLEEVE
Fig. 22 RECLINER HANDLE - MANUAL
1 - CUSHION SIDE COVER
2 - RECLINER SPLINE
3 - SCREW
4 - RECLINER HANDLE
Fig. 23 ARMREST
1 - SEAT BACK
2 - ARMREST
3 - SHOULDER BOLT
4 - CAP
5 - WASHER
6 - STOP SCREW
CS
SEATS
23 - 127
HEADREST (Continued)
SEAT TOWEL BAR
REMOVAL
(1) From the underside of the seat, squeeze ends of
towel bar inward to release from pivot studs (Fig.
24).
(2) Remove towel bar from seat track.
INSTALLATION
(1) Place towel bar into position under seat (Fig.
24).
(2) Squeeze ends of towel bar inward to install on
pivot studs.
SECOND ROW SEAT
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove two nuts attaching seat to floor pan
(Fig. 25).
(3) Tilt seat forward and disconnect heated seat
wire connector (Fig. 26).
(4) Remove seat from vehicle.
Fig. 24 SEAT TOWEL BAR
1 - TOWEL BAR
2 - SEAT TRACK
Fig. 25 SECOND ROW SEATS
1 - SEAT TO FLOOR WASHER AND NUT(S)
2 - SECOND ROW BUCKET SEAT
3 - WIRE CONNECTOR
4 - WELD STUDS
23 - 128
SEATS
CS
INSTALLATION
(1) Place second row seat into position in vehicle.
(2) Connect heated seat wire connector (Fig. 26).
(3) Install two nuts attaching seat to floor pan.
Tighten nuts to 54 N·m (40 ft. lbs.) torque. (Fig. 25).
(4) Install headrest. (Refer to 23 - BODY/SEATS/
HEADREST - INSTALLATION).
(5) Connect battery negative cable.
SECOND ROW SEAT BACK
CUSHION FOAM/COVER
REMOVAL
(1) Disconnect and isolate the battery negative cable.
(2) Remove headrest and sleeves. (Refer to 23 -
BODY/SEATS/HEADREST - REMOVAL).
(3) Remove second row seat. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT - REMOVAL).
(4) Disconnect heat element wire harness.
(5) Remove armrest. (Refer to 23 - BODY/SEATS/
SEAT ARMREST - REMOVAL).
(6) Remove seat inner panel. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT INNER PANEL -
REMOVAL).
(7) Remove outboard side handle (lift on back side
of handle where it engages retainer tab and pull off).
(8) Remove two screws attaching inboard side
shield.
(9) Remove three screws attaching outboard side
shield.
(10) Disengage outer J-straps at seat back (Fig. 27).
(11) Remove screws attaching trim ring to seat
back frame (Fig. 28) and (Fig. 29).
Fig. 27 SECOND ROW SEAT BACK COVER
1 - SECOND ROW SEAT BACK COVER
2 - J-STRAPS
3 - SECOND ROW SEAT ASSEMBLY
Fig. 28 SECOND ROW SEAT BACK TRIM RING
1 - TRIM RING
2 - J-STRAPS
3 - ATTACHING SCREWS
Fig. 26 SECOND ROW DISCONNECT HEATED SEAT
WIRE CONNECTOR
1 - DISCONNECT HEATED CONNECTOR
2 - RELEASE LOCK TABS
CS
SEATS
23 - 129
SECOND ROW SEAT (Continued)
(12) Remove trim ring (Fig. 29).
(13) Disengage inner J-straps from trim ring (Fig.
30).
(14) Disconnect wiring harness (for heated seats)
at inner shield and feed back harness through hole in
shield.
(15) Remove seat back foam/cover and heating har-
ness assembly together (keep trim attached to foam
pad).
NOTE: Use care not to damage wire harness during
removal procedure.
(16) Disconnect heat seat wire harness from three
attachments and route to under side of cushion pad.
(17) Remove cushion and cover from seat back
frame (Fig. 31).
(18) Work the foam and cover under recliner
torque rod and remove seat foam/cover (Fig. 32).
(19) Separate seat cover from foam.
Fig. 29 TRIM RING FOR SEAT BACK FRAME
1 - SECOND ROW SEAT BACK FRAME
2 - TRIM RING FOR SEAT BACK FRAME
3 - SEAT BACK CUSHION
Fig. 30 SEAT BACK J-STRAPS
1 - J-STRAPS
2 - SECOND ROW SEAT BACK COVER
Fig. 31 SECOND ROW SEAT BACK FRAME AND
COVER
1 - SEAT BACK FOAM PAD
2 - SEAT BACK COVER
3 - SEAT BACK FRAME
Fig. 32 SECOND ROW SEAT BACK CUSHION AND
COVER REMOVAL
1 - SECOND ROW SEAT RECLINER TORQUE ROD
2 - SEAT BACK FOAM/COVER
23 - 130
SEATS
CS
SECOND ROW SEAT BACK CUSHION FOAM/COVER (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст