Chrysler Pacifica. Manual — part 821
(17) Disconnect brake light wiring connectors.
(18) Remove steering column retaining nuts (Fig.
7).
(19) Remove shift interlock cable. (Refer to 21 -
TRANSMISSION/TRANSAXLE/AUTOMATIC
-
41TE/SHIFT INTERLOCK CABLE - INSTALLA-
TION).
(20) Remove both left and right side A-pillar trim.
(Refer to 23 - BODY/INTERIOR/A-PILLAR TRIM -
REMOVAL).
(21) Remove instrument panel end caps. (Refer to
23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL END CAP - REMOVAL).
(22) Remove both front door sill scuff plates. (Refer
to 23 - BODY/INTERIOR/FRONT DOOR SCUFF
PLATE - REMOVAL).
(23) Remove both cowl side trim panel. (Refer to
23 - BODY/INTERIOR/COWL SIDE TRIM PANEL -
REMOVAL).
(24) Disconnect the antenna lead connector. (Refer
to 8 - ELECTRICAL/AUDIO/ANTENNA BODY &
CABLE - REMOVAL).
(25) Remove the glove box:
(a) Push in on sides of glove box bin and lower
door.
(b) Pivot glove box downward and disengage
hinge hooks from instrument panel.
(c) Remove glove box from vehicle.
(26) Disconnect the airbag module electrical connec-
tor.
(27) Remove top cover (Fig. 8). (Refer to 23 - BODY/
INSTRUMENT PANEL/INSTRUMENT PANEL TOP
COVER - REMOVAL).
(28) Remove
mounting
screws
attaching
right
instrument panel side cowl bracket (roll down) (Fig.
9).
(29) Disconnect HVAC electrical connectors.
(30) Disconnect (3) electrical connectors behind cowl
panel.
(31) Disconnect right side electrical connector from
A-pillar.
Fig. 7 TOP COVER AND INSTRUMENT PANEL
1 - INSTRUMENT TOP COVER
2 - MOUNTING SCREWS
3 - INSTRUMENT PANEL
4 - ATTACHING NUTS
5 - WELD STUD
6 - STEERING COLUMN ATTACHING BRACKET
7 - INSTRUMENT PANEL SIDE COWL BRACKET
8 - COWL SIDE PANEL
9 - INSTRUMENT PANEL END CAP
CS
INSTRUMENT PANEL
23 - 79
INSTRUMENT PANEL ASSEMBLY (Continued)
Fig. 8 INSTRUMENT PANEL TOP COVER
1 - INSTRUMENT PANEL TOP COVER
2 - AREA TO CHECK FIT AND FINISH
3 - LOCKING TABS
4 - LOCATING PIN(S)
Fig. 9 SIDE COWL ATTACHING BRACKET
1 - INSTRUMENT PANEL
2 - INSTRUMENT PANEL SIDE COWL ATTACHING BRACKET
3 - MOUNTING SCREWS
23 - 80
INSTRUMENT PANEL
CS
INSTRUMENT PANEL ASSEMBLY (Continued)
(32) Remove the (2) screws attaching the instru-
ment panel frame to the dash panel below windshield
opening. (Fig. 10)
(33) With the help of an assistant remove the
instrument panel from vehicle. Lift the instrument
panel up off the HVAC so you won’t damage the seal-
ing surface of the distribution duct.
If the instrument panel is being replaced, transfer
all parts to the new instrument panel assembly.
INSTALLATION
(1) With the help of an assistant place the instru-
ment panel into vehicle inserting instrument panel
locator pins into body. As you install the instrument
panel, lift the instrument panel up so the duct work
does not bind or bend and you can set it down on the
HVAC housing to get the proper seal at the distribu-
tion duct. Get one bolt started in the dash panel.
(2) Install instrument panel side cowl bracket
right and left side mounting screws (Fig. 9).
(3) Install (2) screws attaching the instrument
panel frame to the dash panel below windshield
opening (Fig. 10).
(4) Connect right side electrical connector at A-pil-
lar.
(5) Connect (3) electrical connectors behind cowl
panel.
(6) Connect HVAC electrical connectors.
(7) Install top cover (Fig. 8). (Refer to 23 - BODY/
INSTRUMENT PANEL/INSTRUMENT PANEL TOP
PAD - INSTALLATION).
(8) Install the glove box:
(a) Connect glove box lamp through opening.
(b) Set glove box into opening push into position.
(9) Connect the airbag module electrical connector.
(10) Connect the antenna lead connector. (Refer to
8
-
ELECTRICAL/AUDIO/ANTENNA
BODY
&
CABLE - INSTALLATION).
(11) Install both cowl side trim panel. (Refer to 23
- BODY/INTERIOR/COWL TRIM - INSTALLATION).
(12) Install both front door sill scuff plates. (Refer
to 23 - BODY/INTERIOR/FRONT DOOR SCUFF
PLATE - INSTALLATION).
(13) Install instrument panel end caps. (Refer to
23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL END CAP - INSTALLATION).
(14) Install both left and right side A-pillar trim.
(Refer to 23 - BODY/INTERIOR/A-PILLAR TRIM -
REMOVAL).
(15) Install shift interlock cable. (Refer to 21 -
TRANSMISSION/TRANSAXLE/AUTOMATIC
-
41TE/SHIFT INTERLOCK CABLE - INSTALLA-
TION).
(16) Install steering column retaining nuts (Fig. 7).
(17) Connect brake light wiring connectors.
(18) Install instrument panel reinforcement (Fig. 6).
(19) Connect
steering
column
pinch
bolt
and
retaining nuts (4). (Refer to 19 - STEERING/COL-
UMN/INTERMEDIATE SHAFT - INSTALLATION).
(20) Connect steering column wiring connectors.
(21) Install upper and lower steering column
shrouds.
(Refer
to
19
-
STEERING/COLUMN/
LOWER SHROUD - INSTALLATION) and (Refer to
19
-
STEERING/COLUMN/UPPER
SHROUD
-
INSTALLATION).
(22) Connect body control module wiring connectors.
(23) Connect bulkhead wiring harness connectors.
Fig. 10 INSTRUMENT PANEL SLIP BRACKETS
1 - MOUNTING SCREWS
2 - INSTRUMENT PANEL
3 - INSTRUMENT PANEL SLIP BRACKETS
CS
INSTRUMENT PANEL
23 - 81
INSTRUMENT PANEL ASSEMBLY (Continued)
(24) 2Install screws attaching braking brake han-
dle onto brake park release bracket.
(25) Press on instrument panel trim outlet plate to
engage clips.
(26) Install two screws attaching instrument panel
trim plate (Fig. 5).
(27) Install inflatable knee blocker four mounting
screws.
(28) Install steering column opening cover. (Refer
to 23 - BODY/INSTRUMENT PANEL/STEERING
COLUMN OPENING COVER - INSTALLATION).
(29) Install nuts attaching the floor braces to
instrument panel (Fig. 3). (Refer to 23 - BODY/IN-
STRUMENT PANEL/INSTRUMENT PANEL FLOOR
BRACKET - INSTALLATION)
(30) Install two screws attaching front floor con-
sole L-brackets to instrument panel. (Refer to 23 -
BODY/INTERIOR/FLOOR
CONSOLE
BASE
ASSEMBLY - INSTALLATION).
(31) Install screws attaching front floor console to
instrument panel. (Refer to 23 - BODY/INTERIOR/
FRONT FLOOR CONSOLE - INSTALLATION).
(32) Install center console closeout panels. (Refer
to
23
-
BODY/INTERIOR/CENTER
CONSOLE
CLOSEOUT PANEL - INSTALLATION).
(33) Connect battery negative cable.
INSTRUMENT PANEL CENTER
BEZEL
REMOVAL
(1) Using a trim stick C-4755 or equivalent, disen-
gage the locking tabs attaching instrument panel
center bezel right and/or left side (Fig. 11).
(2) Remove ignition switch bezel.
(3) Remove the instrument panel center bezel(s)
from the vehicle.
INSTALLATION
(1) Place instrument panel center bezel(s) right
and left side into position (Fig. 11).
(2) Apply pressure on instrument panel center
bezel right and/or left side to engage the locking tabs.
(3) Install ignition switch bezel.
INSTRUMENT PANEL FLOOR
BRACKET
REMOVAL
(1) Remove center console closeout panel (Refer to
23 - BODY/INTERIOR/CENTER CONSOLE CLOSE-
OUT PANEL- REMOVAL).
(2) Remove front floor console. (Refer to 23 -
BODY/INTERIOR/FRONT
FLOOR
CONSOLE
-
REMOVAL).
(3) Remove right and/or left floor brace attaching
nuts and remove brace(s) (Fig. 12).
(4) Remove
floor
bracket
attaching
nuts
and
remove bracket.
Fig. 11 INSTRUMENT PANEL CENTER BEZEL
1 - IGNITION SWITCH
2 - CENTER STACK PANEL
3 - INSTRUMENT PANEL
4 - INSTRUMENT PANEL CENTER BEZEL LEFT AND RIGHT
5 - IGNITION SWITCH BEZEL
Fig. 12 FLOOR BRACKET AND BRACES TO
INSTRUMENT PANEL
1 - FLOOR BRACE TO INSTRUMENT PANEL
2 - INSTRUMENT PANEL CENTER BRACE
3 - ATTACHING NUTS
4 - FLOOR BRACKET
23 - 82
INSTRUMENT PANEL
CS
INSTRUMENT PANEL ASSEMBLY (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст