Chrysler Pacifica. Manual — part 820
INSTRUMENT PANEL
TABLE OF CONTENTS
page
page
CLUSTER BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
. . . . . . . . . . . . . . . . . . . . . . . . . 75
GLOVE BOX
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
. . . . . . . . . . . . . . . . . . . . . . . . . 76
GLOVE BOX LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
. . . . . . . . . . . . . . . . . . . . . . . . . 76
GLOVE BOX LATCH STRIKER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
. . . . . . . . . . . . . . . . . . . . . . . . . 76
INSTRUMENT PANEL ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
. . . . . . . . . . . . . . . . . . . . . . . . . 81
INSTRUMENT PANEL CENTER BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
. . . . . . . . . . . . . . . . . . . . . . . . . 82
INSTRUMENT PANEL FLOOR BRACKET
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
. . . . . . . . . . . . . . . . . . . . . . . . . 83
INSTRUMENT PANEL END CAP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
. . . . . . . . . . . . . . . . . . . . . . . . . 83
INSTRUMENT PANEL TOP COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
. . . . . . . . . . . . . . . . . . . . . . . . . 84
STEERING COLUMN OPENING COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
. . . . . . . . . . . . . . . . . . . . . . . . . 85
CLUSTER BEZEL
REMOVAL
(1) Open hood, disconnect and isolate the battery
negative cable.
(2) Remove the steering opening cover two retain-
ing screws and cover.
(3) Remove the knee blocker airbag (Refer to 8 -
ELECTRICAL/RESTRAINTS/KNEE BLOCKER AIR-
BAG - REMOVAL).
(4) Unsnap the left end cover and remove.
(5) Remove the two screws to the left lower instru-
ment panel trim plate.
(6) Remove the instrument panel center bezel
(Refer to 23 - BODY/INSTRUMENT PANEL/IN-
STRUMENT PANEL CENTER BEZEL - REMOVAL).
(7) Remove the eight retaining screws to the clus-
ter bezel (Fig. 1).
(8) Using a trim stick or equivalent, gently pry out
on cluster bezel around edges and remove from
instrument panel (Fig. 2).
(9) Disconnect
the
electrical
connector
to
the
instrument panel switch pod (EVIC, NAV, Clock, and
Hazard Switch).
INSTALLATION
(1) Connect the electrical connector to the instru-
ment panel switch pod (EVIC, NAV, Clock, and Haz-
ard Switch).
(2) Position the cluster bezel over retaining slots
and firmly snap into place (Fig. 2).
(3) Install the eight retaining screws to the cluster
bezel (Fig. 1).
(4) Position the left side instrument panel center
stack trim from panel over retaining slots and firmly
snap into place.
(5) Install the instrument panel center bezel (Refer
to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL CENTER BEZEL - INSTALLATION).
(6) Position the left lower instrument panel trim
plate over the retaining slots and firmly snap into
place. Install the two screws.
(7) Position the left end cover over the retaining
slots and firmly snap into place.
(8) Install the knee blocker airbag (Refer to 8 -
ELECTRICAL/RESTRAINTS/KNEE BLOCKER AIR-
BAG - INSTALLATION).
(9) Position the steering opening cover over retain-
ing and firmly snap into place. Install the two retain-
ing screws.
Fig. 1 CLUSTER BEZEL MOUNTING SCREW
LOCATION
CS
INSTRUMENT PANEL
23 - 75
WARNING: DO NOT CONNECT THE BATTERY NEG-
ATIVE
CABLE.
(Refer
to
8
-
ELECTRICAL/RE-
STRAINTS - DIAGNOSIS AND TESTING - AIRBAG
SYSTEM) FIRST.
(10) Verify vehicle and system operation.
GLOVE BOX
REMOVAL
(1) Open glove box.
(2) Push in on sides of glove box bin and lower
door.
(3) Pivot glove box downward and disengage hinge
hooks from instrument panel.
(4) Remove glove box.
INSTALLATION
(1) Place glove box in position.
(2) Engage hinge hooks into instrument panel and
pivot glove box upward.
(3) Push in sides of glove box bin and snap glove
box assembly into instrument panel.
(4) Close glove box door.
GLOVE BOX LATCH
REMOVAL
(1) Open glove box.
(2) Push in on sides of glove box bin and lower
door.
(3) Pivot glove box downward and disengage hinge
hooks from instrument panel.
(4) Remove glove box.
(5) Remove the assembly screws.
(6) Disassemble the glove box.
(7) Separate the latch from the glove box assembly.
INSTALLATION
(1) Install the latch onto the glove box assembly.
(2) Assemble the glove box.
(3) Install the assembly screws.
(4) Engage hinge hooks into instrument panel and
pivot glove box upward.
(5) Push in sides of glove box bin and snap glove
box assembly into instrument panel.
(6) Close glove box door.
GLOVE BOX LATCH STRIKER
REMOVAL
(1) Open glove box door.
(2) Remove screws holding lock striker to instru-
ment panel.
(3) Remove glove box latch striker.
INSTALLATION
(1) Install the glove box latch striker.
(2) Install the screws holding latch striker to
instrument panel.
(3) Close glove box door.
Fig. 2 CLUSTER BEZEL - REMOVE/INSTALL
23 - 76
INSTRUMENT PANEL
CS
CLUSTER BEZEL (Continued)
INSTRUMENT PANEL
ASSEMBLY
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove center console closeout panel. (Refer to
23 - BODY/INTERIOR/CENTER CONSOLE CLOSE-
OUT PANEL - REMOVAL).
(3) Remove front floor console assembly. (Refer to
23
-
BODY/INTERIOR/FLOOR
CONSOLE
-
REMOVAL).
(4) Remove floor console base assembly two screws
attaching L-brackets to instrument panel. (Refer to
23 - BODY/INTERIOR/FLOOR CONSOLE BASE
ASSEMBLY - REMOVAL).
(5) Remove nuts attaching the floor braces to
instrument panel (Fig. 3). (Refer to 23 - BODY/IN-
STRUMENT PANEL/INSTRUMENT PANEL FLOOR
BRACKET - REMOVAL).
(6) Remove steering column opening cover. (Refer
to 23 - BODY/INSTRUMENT PANEL/STEERING
COLUMN OPENING COVER - REMOVAL).
(7) Remove inflatable knee blocker four mounting
screws (Fig. 4).
(8) Remove two screws attaching instrument panel
trim outlet plate (Fig. 5).
(9) Using a trim stick C-4755 or equivalent, disen-
gage the locking tabs attaching instrument panel
trim plate.
(10) Disengage braking brake handle from brake
park release bracket, leave rod engaged.
(11) Remove instrument panel reinforcement (Fig.
6).
(12) Disconnect bulkhead wiring harness connec-
tors.
Fig. 3 FLOOR BRACKET AND BRACES TO
INSTRUMENT PANEL
1 - FLOOR BRACE TO INSTRUMENT PANEL
2 - INSTRUMENT PANEL CENTER BRACE
3 - ATTACHING NUTS
4 - FLOOR BRACKET
Fig. 4 INFLATABLE KNEE BLOCKER
1 - WIRE CONNECTOR
2 - INSTRUMENT PANEL
3 - INSTRUMENT PANEL BRACKET
4 - INFLATABLE KNEE BLOCKER
5 - INSTRUMENT PANEL REINFORCEMENT
6 - MOUNTING SCREWS
CS
INSTRUMENT PANEL
23 - 77
(13) Disconnect body control module wiring connec-
tors.
(14) Remove upper and lower steering column
shrouds.
(Refer
to
19
-
STEERING/COLUMN/
LOWER SHROUD - REMOVAL) and (Refer to 19 -
STEERING/COLUMN/UPPER
SHROUD
-
REMOVAL).
(15) Disconnect steering column wiring connectors.
(16) Disconnect steering column pinch bolt and
retaining nuts (4). (Refer to 19 - STEERING/COL-
UMN/INTERMEDIATE SHAFT - REMOVAL).
Fig. 6 INSTRUMENT PANEL LOWER REINFORCEMENT
1 - WELD STUDS
2 - INSTRUMENT PANEL
3 - MOUNTING SCREWS
4 - INSTRUMENT PANEL REINFORCEMENT
5 - STUDS
6 - ATTACHING NUTS
7 - INSTRUMENT TO FLOOR BRACKET
8 - INSTRUMENT PANEL BRACE TO FLOOR BRACKET
9 - INSTRUMENT PANEL REINFORCEMENT
10 - DIAGNOSTIC REMOTE CONNECTOR BRACKET
11 - DIAGNOSTIC WIRE CONNECTOR
12 - INSTRUMENT PANEL SIDE COWL BRACKET
Fig. 5 PARK BRAKE RELEASE HANDLE & STEERING COLUMN OUTER COVER
1 - INSTRUMENT PANEL TRIM OUTLET PLATE
2 - ATTACHING SCREWS
3 - INSTRUMENT PANEL PARKING BRAKE RELEASE HANDLE
BRACKET
4 - INSTRUMENT PANEL
5 - INFLATABLE KNEE BLOCKER AIRBAG
6 - INSTRUMENT PANEL STEERING COLUMN OPENING COVER
7 - INSTRUMENT PANEL CLUSTER POCKET
8 - BRAKE RELEASE HANDLE
9 - BRAKE HANDLE BRACKET ASSEMBLY
23 - 78
INSTRUMENT PANEL
CS
INSTRUMENT PANEL ASSEMBLY (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст