Chrysler Pacifica. Manual — part 823
A-PILLAR TRIM
REMOVAL
(1) Disengage hidden clips attaching A-pillar trim
panel to A-pillar (Fig. 1).
(2) Remove A-pillar trim from vehicle.
INSTALLATION
(1) Position foot on A-pillar trim panel into instru-
ment panel top cover channel (Fig. 1).
(2) Position A-pillar trim in vehicle.
(3) Align locator pins.
(4) Press on A-pillar trim panel to engage locking
clips.
ASSIST HANDLE
REMOVAL
(1) Using a trim stick (C-4755), remove screw
access covers from grab handle.
(2) Remove screws holding grab handle to roof rail.
(3) Remove grab handle from vehicle.
INSTALLATION
(1) Place grab-handle in position on vehicle.
(2) Install grab handle attaching screws to roof
rail.
(3) Install screw access covers into grab handle.
B-PILLAR LOWER TRIM
REMOVAL
(1) Slide lower seat belt cover rearward to expose
anchor bolt.
(2) Remove bolt attaching lower seat belt anchor to
floor (Fig. 2).
(3) Remove upper B-pillar trim cover.
(4) Remove access panel from B-pillar trim.
(5) Disengage hidden clips attaching lower trim
cover to B-pillar.
(6) Remove lower B-pillar trim cover from vehicle.
INSTALLATION
(1) Place lower B-pillar trim cover in position on
vehicle (Fig. 2).
(2) Insert seat belt through hole in lower B-pillar
trim.
(3) Engage hidden clips attaching lower trim cover
to B-pillar.
(4) Install access cover.
(5) Install upper B-pillar trim cover.
(6) Place seat belt anchor in position on floor so
webbing is pointed rearward and slightly outboard.
(7) Install bolt attaching lower seat belt anchor to
floor. Tighten all seat belt bolts to 39 N·m (29 ft. lbs.)
torque.
(8) Verify that seat belt anchor does not interfere
with seat track travel.
Fig. 1 A-PILLAR TRIM PANEL
1 - INSTRUMENT PANEL UPPER RETAINER PANEL
2 - BODY SIDE ASSEMBLY
3 - A-PILLAR TRIM PANEL
Fig. 2 B-PILLAR LOWER TRIM PANEL
1 - B-PILLAR
2 - B-PILLAR UPPER TRIM PANEL
3 - TURNING LOOP ADJUSTER COVER
4 - B-PILLAR UPPER SEAT BELT BOLT
5 - SEAT BELT ASSEMBLY
6 - B-PILLAR LOWER SEAT BELT BOLT
7 - B-PILLAR LOWER SEAT BELT ANCHOR COVER
8 - B-PILLAR LOWER TRIM PANEL
9 - SEAT BELT RETRACTOR
CS
INTERIOR
23 - 87
B-PILLAR UPPER TRIM
REMOVAL
(1) Remove bolt attaching lower seat belt anchor to
floor.
(2) Lower shoulder belt height adjuster to the bot-
tom of travel.
(3) Remove shoulder belt turning loop from height
adjuster.
(4) Use
a
Snap-on
t Trim Pad Remover tool
(A179A), or equivalent, and remove shoulder belt
height adjuster knob.
(5) Remove shoulder belt bezel from trim cover
(Fig. 3).
(6) Remove screw attaching trim cover to B-pillar
from inside bezel cavity.
(7) Disengage hidden clips attaching trim cover to
B-pillar.
(8) Remove B-pillar trim cover from vehicle.
INSTALLATION
(1) Insert seat belt through B-pillar trim and web
guide (Fig. 3).
(2) Place B-pillar trim cover in position on vehicle.
(3) Engage hidden clips attaching trim cover to
B-pillar.
(4) Install shoulder belt bezel into trim cover.
(5) Install height adjuster knob.
(6) Install shoulder belt turning loop onto height
adjuster. Tighten bolt to 39 N·m (29 ft. lbs.) torque.
(7) Place seat anchor in position on floor so web-
bing is pointed rearward and slightly outboard.
(8) Install bolt attaching lower seat belt anchor to
floor. Tighten seat belt bolt to 39 N·m (29 ft. lbs.)
torque.
CARPETS
REMOVAL
(1) Remove front seats. (Refer to 23 - BODY/
SEATS/FRONT SEAT - REMOVAL).
(2) Remove first row seats. (Refer to 23 - BODY/
SEATS/FIRST ROW SEAT - REMOVAL).
(3) Remove second row seats. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT - REMOVAL).
(4) Remove move shifter knob. (Refer to 21 -
TRANSMISSION/TRANSAXLE/AUTOMATIC
-
41TE/GEAR SHIFT KNOB - REMOVAL).
(5) Remove front floor console shift bezel. (Refer to
23 - BODY/INTERIOR/SHIFT BEZEL - REMOVAL).
(6) Remove front floor console. (Refer to 23 -
BODY/INTERIOR/FRONT
FLOOR
CONSOLE
-
REMOVAL).
(7) Remove rear floor console. (Refer to 23 - BODY/
INTERIOR/REAR FLOOR CONSOLE - REMOVAL).
(8) Floor console base assembly. (Refer to 23 -
BODY/INTERIOR/FLOOR CONSOLE - REMOVAL).
(9) Remove front and rear sill scuff plates. (Refer
to
23
-
BODY/INTERIOR/FRONT
DOOR
SILL
SCUFF PLATE - REMOVAL) and (Refer to 23 -
BODY/INTERIOR/REAR DOOR SCUFF PLATE -
REMOVAL).
(10) Remove cowl side trim panels. (Refer to 23 -
BODY/INTERIOR/COWL SIDE TRIM - REMOVAL).
(11) Remove the floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE BIN -
REMOVAL).
(12) Remove liftgate sill scuff plate. (Refer to 23 -
BODY/INTERIOR/LIFTGATE SILL SCUFF PLATE -
REMOVAL).
(13) Remove B-pillar lower trim. (Refer to 23 -
BODY/INTERIOR/B-PILLAR
LOWER
TRIM
-
REMOVAL).
(14) Remove quarter trim panel. (Refer to 23 -
BODY/INTERIOR/QUARTER
TRIM
PANEL
-
REMOVAL).
(15) Remove fasteners attaching carpet to floor
panel (Fig. 4).
CAUTION: Use care when pulling wires and connec-
tors through the carpet.
(16) Pull wire harnesses and connector through
carpet.
Fig. 3 B-PILLAR UPPER TRIM PANEL
1 - B-PILLAR
2 - B-PILLAR UPPER TRIM PANEL
3 - ATTACHING SCREW
4 - LOCATING PIN
5 - 4-WAY LOCATOR PIN
23 - 88
INTERIOR
CS
(17) Roll carpet from under instrument panel rear-
ward to rear of vehicle and remove.
(18) Rear floor carpet roll and fold carpet forward
away from rear door opening and remove from vehi-
cle.
(19) Remove floor silencer from vehicle (Fig. 5).
INSTALLATION
(1) Place floor silencer into position in vehicle (Fig.
5).
(2) Insert rear floor carpet into position in vehicle.
(3) Insert front carpet. Move carpet into position
under instrument panel. Work carpet rearward into
position.
CAUTION: Use care when pulling wires and connec-
tors through the carpet.
(4) Pull wire harnesses and connectors through
carpet.
(5) Install fasteners attaching carpet to floor (Fig.
4).
(6) Install quarter trim panel. (Refer to 23 -
BODY/INTERIOR/QUARTER
TRIM
PANEL
-
INSTALLATION).
(7) Install B-pillar lower trim. (Refer to 23 -
BODY/INTERIOR/B-PILLAR
LOWER
TRIM
-
INSTALLATION).
(8) Install liftgate sill scuff plate. (Refer to 23 -
BODY/INTERIOR/LIFTGATE SILL SCUFF PLATE -
INSTALLATION).
(9) Install the floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE BIN -
INSTALLATION).
(10) Install cowl side trim panels. (Refer to 23 -
BODY/INTERIOR/COWL SIDE TRIM - INSTALLA-
TION).
(11) Install front and rear sill scuff plates. (Refer
to
23
-
BODY/INTERIOR/FRONT
DOOR
SILL
Fig. 4 FLOOR CARPET
1 - FRONT FLOOR CARPET
2 - PUSH PIN(S)
3 - REAR FLOOR CARPET
4 - GROMMET
5 - FRONT FULL FLOOR PANEL
Fig. 5 REAR FLOOR SILENCER
1 - REAR FLOOR SILENCER
2 - REAR FLOOR
CS
INTERIOR
23 - 89
CARPETS (Continued)
SCUFF PLATE - INSTALLATION), and (Refer to 23
-
BODY/INTERIOR/REAR
DOOR
SILL
SCUFF
PLATE - INSTALLATION).
(12) Install floor console base assembly. (Refer to
23 - BODY/INTERIOR/FLOOR CONSOLE BASE
ASSEMBLY - INSTALLATION).
(13) Install rear floor console. (Refer to 23 - BODY/
INTERIOR/REAR FLOOR CONSOLE - INSTALLA-
TION).
(14) Install front floor console. (Refer to 23 -
BODY/INTERIOR/FRONT
FLOOR
CONSOLE
-
INSTALLATION).
(15) Install front floor console shift bezel. (Refer to
23 - BODY/INTERIOR/SHIFT BEZEL - INSTALLA-
TION).
(16) Install shifter knob. (Refer to 21 - TRANS-
MISSION/TRANSAXLE/AUTOMATIC - 41TE/GEAR
SHIFT KNOB - INSTALLATION).
(17) Install second row seats. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT - INSTALLATION).
(18) Install first row seats. (Refer to 23 - BODY/
SEATS/FIRST ROW SEAT - INSTALLATION).
(19) Install front seats. (Refer to 23 - BODY/
SEATS/FRONT SEAT - INSTALLATION).
CENTER CONSOLE CLOSEOUT
PANEL
REMOVAL
(1) Remove attaching screw (Fig. 6) and/or (Fig. 7)
(2) Remove center console closeout panel.
INSTALLATION
(1) Place center console closeout panel into posi-
tion (Fig. 6) and/or (Fig. 7)
(2) Install attaching screw.
Fig. 6 LEFT CONSOLE CLOSEOUT PANEL
1 - ATTACHING SCREW
2 - LEFT CONSOLE CLOSEOUT PANEL
Fig. 7 RIGHT CONSOLE CLOSEOUT PANEL
1 - RIGHT CONSOLE CLOSEOUT PANEL
2 - ATTACHING SCREW
23 - 90
INTERIOR
CS
CARPETS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст