Chrysler Pacifica. Manual — part 379
TEST
ACTION
APPLICABILITY
7
Turn the ignition off.
Disconnect the Brake Switch harness connector.
Disconnect the PCM harness connector.
Measure the resistance between ground and the (V32) S/C Supply circuit at the
Speed Control Servo harness connector.
Is the resistance below 100 ohms?
All
Yes
→ Repair the short to ground in the (V32) S/C Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4 - NGC.
No
→ Go To 8
8
Turn the ignition off.
Disconnect the S/C Servo harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (V35) S/C Vent Sol Control circuit from the Speed
Control Servo harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 9
No
→ Repair the open/high resistance in the (V35) S/C Vent Sol Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4 - NGC.
9
Turn the ignition off.
Disconnect the S/C Servo harness connector.
Disconnect the PCM harness connector.
Measure the resistance between ground and the (V35) S/C Vent Sol Control circuit at
the Speed Control Servo harness connector.
Is the resistance below 100 ohms?
All
Yes
→ Repair the short to ground in the (V35) Speed Control Vent
Solenoid Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4 - NGC.
No
→ Go To 10
10
NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If the there are no possible causes remaining, view repair.
All
Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 4 - NGC.
237
DRIVEABILITY - NGC
P0586-SPEED CONTROL VENT SOLENOID CIRCUIT —
Continued
Symptom:
P0594-SPEED CONTROL SERVO POWER CIRCUIT
When Monitored and Set Condition:
P0594-SPEED CONTROL SERVO POWER CIRCUIT
When Monitored:
With the ignition key on. The speed control switched on.
Set Condition:
The PCM detects a open or short in the Speed Control Power Supply
circuit. One Trip Fault.
POSSIBLE CAUSES
(V30) S/C BRAKE SWITCH OUTPUT CIRCUIT
(V32) S/C POWER SUPPLY CIRCUIT
(V30) S/C BRAKE SWITCH OUTPUT CIRCUIT SHORTEDTO GROUND
(V32) S/C POWER SUPPLY CIRCUIT SHORTED TO GROUND
(V30) S/C BRAKE SWITCH OUTPUT CIRCUIT OPEN
BRAKE LAMP SWITCH
PCM (S/C SOURCE CIRCUIT)
TEST
ACTION
APPLICABILITY
1
Turn the ignition off.
Disconnect the Speed Control Servo harness connector.
Ignition on, engine not running.
NOTE: It is necessary to PRESS and HOLD the Speed Control Switch in the
ON position while checking for voltage.
Using a 12-volt test light connected to ground, probe the (V30) S/C Brake Switch
Output terminal in the Servo Harness connector.
Does the test light illuminate brightly?
All
Yes
→ Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No
→ Go To 2
238
DRIVEABILITY - NGC
TEST
ACTION
APPLICABILITY
2
Turn the ignition off.
Disconnect the PCM harness connector.
Disconnect the Brake Lamp Switch harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (V32) S/C Power Supply circuit from the Brake Lamp
Switch harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 3
No
→ Repair the open/high resistance in the (V32) S/C Power Supply
circuit between the PCM and Brake Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
3
Turn the ignition off.
Disconnect the PCM harness connector.
Disconnect the Brake Switch harness connector.
Measure the resistance between ground and the (V32) S/C Power Supply circuit in
the Brake Switch harness connector.
Is the resistance below 100 ohms?
All
Yes
→ Go To 4
No
→ Repair the short to ground in the (V32) S/C Power Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
4
Turn the ignition off.
Disconnect the Speed Control Servo harness connector.
Disconnect the Brake Switch harness connector.
Measure the resistance between ground and the (V30) S/C Brake Switch Output
circuit at the Speed Control Servo harness connector.
Is the resistance below 100 ohms?
All
Yes
→ Repair the short to ground in the (V30) S/C Brake Switch Output
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No
→ Go To 5
5
Turn the ignition off.
Disconnect the S/C Servo harness connector.
Disconnect the Brake Switch harness connector.
Measure the resistance of the (V30) S/C Brake Switch Output circuit from the Brake
Switch harness connector to the S/C Servo harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 6
No
→ Repair the open/high resistance in the (V30) S/C Brake Switch
Output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
239
DRIVEABILITY - NGC
P0594-SPEED CONTROL SERVO POWER CIRCUIT —
Continued
TEST
ACTION
APPLICABILITY
6
Disconnect the Brake Lamp Switch harness connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (V32) Speed Control Power
Supply circuit in the Brake Lamp Switch harness connector.
NOTE: It is necessary to HOLD the Cruise Control Switch in the ON position
to get an accurate reading.
Does the test light illuminate brightly?
All
Yes
→ Replace the Brake Lamp Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No
→ Go To 7
7
NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.
All
Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
240
DRIVEABILITY - NGC
P0594-SPEED CONTROL SERVO POWER CIRCUIT —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст