Chrysler Pacifica. Manual — part 510
REMOVAL
LEFT MULTI-FUNCTION SWITCH
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the lower steering column shroud
(Refer
to
19
-
STEERING/COLUMN/LOWER
SHROUD - REMOVAL).
(3) Remove the upper steering column shroud
(Refer
to
19
-
STEERING/COLUMN/UPPER
SHROUD - REMOVAL).
(4) Disconnect the instrument panel wire harness
connector from the switch.
(5) Remove the two screws that secure the left
multi-function switch to the housing.
(6) Remove the left multi-function switch from col-
umn and vehicle.
MULTI-FUNCTION SWITCH MOUNTING HOUSING
NOTE: Before starting this procedure, be certain to
turn the steering wheel until the front wheels are in
the straight-ahead position.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the clock spring from the multi-func-
tion switch mounting housing. (Refer to 8 - ELEC-
TRICAL/RESTRAINTS/CLOCK
SPRING
-
REMOVAL).
(3) Remove the left multi-function switch from the
multi-function switch mounting housing (refer to
above procedure).
(4) Remove the right multi-function switch from
the multi-function switch mounting housing. (Refer
to
8
-
ELECTRICAL/WIPERS/WASHERS/RIGHT
MULTI-FUNCTION SWITCH - REMOVAL).
(5) Remove the screw that secures the multi-func-
tion switch mounting housing to the steering column
housing (Fig. 26).
(6) Remove the multi-function switch mounting
housing (Fig. 27) and (Fig. 28).
INSTALLATION
LEFT MULTI-FUNCTION SWITCH
(1) Position the left multi-function switch onto the
housing.
(2) Install the two screws to the left multi-function
switch. Torque the screws to 2.5 N·m (22 in. lbs.).
(3) Reconnect the instrument panel wire harness
connector to the switch.
(4) Install the lower steering column shroud (Refer
to 19 - STEERING/COLUMN/LOWER SHROUD -
INSTALLATION).
(5) Install the upper steering column shroud (Refer to
19 - STEERING/COLUMN/UPPER SHROUD - INSTAL-
LATION). Torque screws to 1.9 N·m (17 in. lbs.).
(6) Reconnect the battery negative cable.
(7) Verify vehicle and system operation.
MULTI-FUNCTION SWITCH MOUNTING HOUSING
NOTE: Before starting this procedure, be certain
that the front wheels are still in the straight-ahead
position.
(1) Rotate the turn signal cancel cam in the multi-
function switch housing until the alignment hole in
the one cam lobe is aligned with the alignment hole
Fig. 26 MULTI-FUNCTION SWITCH MOUNTING
HOUSING SCREW - REMOVE/INSTALL
1 - CLOCK SPRING
2 - SCREW
3 - MULTI-FUNCTION SWITCH MOUNTING HOUSING
Fig. 27 MULTI-FUNCTION SWITCH MOUNTING
HOUSING - REMOVE/INSTALL
1 - MULTI-FUNCTION SWITCH ASSEMBLY
2 - CLOCK SPRING
CS
LAMPS/LIGHTING - EXTERIOR
8L - 23
LEFT MULTI-FUNCTION SWITCH (Continued)
in the back of the housing. The oblong hole in the
hub of the cam should now be at the top, and the
locating tab in the hub of the cam should be at the
bottom (Fig. 29).
(2) Position the multi-function switch housing onto
the top of the steering column. The locating tab in
the hub of the turn signal cancel cam must be
engaged with the alignment groove in the bottom of
the upper steering column shaft.
(3) Install and tighten the screw that secures the
multi-function switch housing to the top of the col-
umn housing (Fig. 26). Torque screw to 1.9 N·m (17
in. lbs.).
(4) Install the right multi-function switch onto the
multi-function switch housing. (Refer to 8 - ELEC-
TRICAL/WIPERS/WASHERS/RIGHT MULTI-FUNC-
TION SWITCH - INSTALLATION).
(5) Install the left multi-function switch onto the
multi-function switch housing (refer to above proce-
dure).
(6) Install the clock spring onto the multi-function
switch housing. (Refer to 8 - ELECTRICAL/RE-
STRAINTS/CLOCK SPRING - INSTALLATION).
(7) Connect the battery negative cable.
(8) Verify vehicle and system operation.
Fig. 28 MULTI-FUNCTION SWITCH - REMOVE/INSTALL
1 - RIGHT MULTI-FUNCTION SWITCH CONNECTOR
4 - CLOCK SPRING RADIO, SPEED CONTROL, AND HORN
CONNECTOR
2 - CLOCK SPRING AIRBAG CONNECTORS
5 - LEFT MULTI-FUNCTION SWITCH CONNECTOR
3 - MULTI-FUNCTION SWITCH ASSEMBLY W/CLOCK SPRING
6 - MULTI-FUNCTION SWITCH MOUNTING HOUSING RETAINING
SCREW
Fig. 29 TURN SIGNAL CANCELLING CAM
ALIGNMENT
1 - ALIGNMENT HOLE
2 - MULTI-FUNCTION SWITCH MOUNTING HOUSING
3 - ALIGNMENT HOLE
4 - TURN SIGNAL CANCEL CAM
5 - LOCATING TAB
6 - WASHER
7 - TURN SIGNAL SWITCH CANCEL ACTUATOR
8L - 24
LAMPS/LIGHTING - EXTERIOR
CS
LEFT MULTI-FUNCTION SWITCH (Continued)
LICENSE PLATE LAMP
REMOVAL
(1) Open hood, disconnect and isolate the battery
negative cable.
(2) Using a trim stick (special tool #C-4755) or
equivalent, gently pry in and then down on the left
side of the lamp cover (Fig. 30) (shown reversed) and
(Fig. 31).
(3) Pull license lamp out of liftgate light bar and
remove.
NOTE: If the license plate lamp unit, located within
the liftgate light bar needs replacing, (Refer to 23 -
BODY/LIFTGATE/LIFTGATE
LIGHT
BAR
-
REMOVAL).
INSTALLATION
(1) Align lamp with slot in socket and firmly push
straight in.
(2) Position the lamp cover over retaining slots
and firmly snap into place (Fig. 31).
(3) Connect the battery negative cable.
(4) Verify vehicle and system operation.
(5) Close hood.
REAR SIDE MARKER LAMP
REMOVAL
(1) Remove the tail lamp unit (Refer to 8 - ELEC-
TRICAL/LAMPS/LIGHTING
-
EXTERIOR/TAIL
LAMP UNIT - REMOVAL).
(2) Twist counterclockwise and pull out lamp from
tail lamp unit.
(3) Pull lamp straight out of lamp socket.
INSTALLATION
(1) Push lamp straight into lamp socket.
(2) Place lamp into tail lamp unit and then twist
clockwise until lamp stops (about 1/4 turn).
(3) Install the tail lamp unit (Refer to 8 - ELEC-
TRICAL/LAMPS/LIGHTING
-
EXTERIOR/TAIL
LAMP UNIT - INSTALLATION).
TAIL LAMP
REMOVAL
(1) Remove the tail lamp unit (Refer to 8 - ELEC-
TRICAL/LAMPS/LIGHTING
-
EXTERIOR/TAIL
LAMP UNIT - REMOVAL).
(2) Twist counterclockwise and pull out lamp from
tail lamp unit.
(3) Pull lamp straight out of lamp socket.
INSTALLATION
(1) Push lamp straight into lamp socket.
(2) Place lamp into tail lamp unit and then twist
clockwise until lamp stops (about 1/4 turn).
(3) Install the tail lamp unit (Refer to 8 - ELEC-
TRICAL/LAMPS/LIGHTING
-
EXTERIOR/TAIL
LAMP UNIT - INSTALLATION).
Fig. 30 LICENSE PLATE LAMP COVER LATCH
1 - LICENSE PLATE LAMP COVER
2 - PLACE TOOL HERE TO PRY
Fig. 31 LICENSE PLATE LAMP COVER - REMOVAL
1 - INSERT HERE TO PRY OFF LICENSE PLATE LAMP COVER
CS
LAMPS/LIGHTING - EXTERIOR
8L - 25
TAIL LAMP UNIT
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Open liftgate, remove two hex head bolts in
inner D-pillar (Fig. 32).
(3) Rotate lamp outboard away from vehicle to
remove tail lamp forward stud from grommet.
(4) Disconnect electrical connector.
(5) If replacing the tail lamp unit, transfer lamps
to new unit.
INSTALLATION
(1) If replacing the tail lamp unit, transfer lamps
to new unit.
(2) Connect electrical connector.
(3) Place tail lamp unit over retaining clip and
push to seat in clip until you hear a snap (Fig. 32).
(4) Install the hex head nut into the D-Pillar (Fig.
32).
(5) Connect the battery negative cable.
(6) Verify vehicle and system operation.
(7) Close liftgate.
Fig. 32 TAIL LAMP UNIT - REMOVE/INSTALL
1 - REAR LIFTGATE OPENING
2 - REAR TAIL LAMP UNIT
8L - 26
LAMPS/LIGHTING - EXTERIOR
CS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст