Chrysler Pacifica. Manual — part 511
LAMPS/LIGHTING - INTERIOR
TABLE OF CONTENTS
page
page
LAMPS/LIGHTING - INTERIOR
. . . . . . . . . . . . . . . . . . . . . . . . . 27
SPECIFICATIONS - INTERIOR LAMPS
DOOR COURTESY LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . 28
DOOR COURTESY LAMP UNIT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . 28
GLOVE BOX LAMP SWITCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 30
ILLUMINATION LAMPS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . 30
LIFTGATE LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . 31
LIFTGATE LAMP UNIT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . 31
READING LAMPS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . 32
VANITY LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . 33
LAMPS/LIGHTING - INTERIOR
DESCRIPTION
COURTESY LAMP CONTROL
The Body Control Module (BCM) has direct control
over all of the vehicle’s courtesy lamps except for the
driver and passenger front courtesy lamps. The
Driver Door Module (DDM) and the Passenger Door
Module (PDM) turn these lamps on based on
requests sent over the PCI Bus from the BCM. The
courtesy lamps will illuminate if:
• Any door is ajar and the courtesy lamp switch
on the headlamp switch is not in the dome OFF posi-
tion.
• The courtesy lamp switch on the headlamp
switch is in the dome ON position.
• A Remote Keyless Entry unlock message is
received.
• The operator unlocks the driver door with the
key (with VTSS only).
ILLUMINATED ENTRY
Illuminated entry will be initiated when the cus-
tomer enters the vehicle by unlocking the doors with
the key fob, or with the key if the vehicle is equipped
with vehicle theft security. Upon exiting the vehicle,
if the lock button is pressed with a door open, illumi-
nated entry will cancel when the door closes. If the
doors are closed and the ignition switch is turned
ON, the illuminated entry also cancels. The illumi-
nated entry feature will not operate if the courtesy
lamp switch is in the dome OFF position.
INTERIOR LIGHTING BATTERY SAVER
If any of the interior lamps are left ON after the
ignition is turned OFF, the BCM will turn them OFF
after fifteen minutes. To return to normal operation,
the courtesy lamps will operate after the dome lamp
switch or door ajar switch changes state. The reading
lamps and glove box lamp operate under the same
conditions as the courtesy lamps.
CS
LAMPS/LIGHTING - INTERIOR
8L - 27
SPECIFICATIONS - INTERIOR LAMPS
BULB APPLICATION TABLE
LAMP
BULB
CENTER AND REAR READING
LAMP
578
FRONT DOOR COURTESY
LAMP
578
LIFTGATE LAMP
578
OVERHEAD CONSOLE
READING LAMPS
578
VISOR VANITY LAMPS
V26377
DOOR COURTESY LAMP
REMOVAL
(1) Open hood, disconnect and isolate the battery
negative cable.
(2) Open door.
(3) Using a trim stick (special tool #C-4755) or
equivalent, gently pry out on door courtesy lamp lens
and remove from trim panel (Fig. 1).
(4) Gently pry up on one end of the door courtesy
lamp and pull out of lamp unit (Fig. 2).
INSTALLATION
(1) Place lamp over retaining clips in door courtesy
lamp unit retaining clips and firmly snap into place
(Fig. 2).
(2) Place the door courtesy lamp lens over the
retaining pins making sure that they are lined up
and them firmly snap into place (Fig. 1).
(3) Close door.
(4) Connect the battery negative cable.
(5) Verify vehicle and system operation.
DOOR COURTESY LAMP UNIT
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the front door trim panel (Refer to 23 -
BODY/DOOR - FRONT/TRIM PANEL - REMOVAL)
and (Fig. 3).
(3) With the trim panel on the bench, push in on
the side retaining clips of the door courtesy lamp
unit and push through trim panel to remove (Fig. 4).
INSTALLATION
(1) Align the door courtesy lamp unit in the door
trim panel opening and firmly snap into place (Fig.
4).
(2) Install the front door trim panel (Refer to 23 -
BODY/DOOR - FRONT/TRIM PANEL - INSTALLA-
TION) and (Fig. 3).
Fig. 1 DOOR COURTESY LAMP LENS - REMOVAL
1 - DOOR COURTESY LAMP LENS
2 - TRIM STICK (SPECIAL TOOL #C-4755)
Fig. 2 DOOR COURTESY LAMP - REMOVAL
8L - 28
LAMPS/LIGHTING - INTERIOR
CS
LAMPS/LIGHTING - INTERIOR (Continued)
(3) Connect the battery negative cable.
(4) Verify vehicle and system operation.
GLOVE BOX LAMP SWITCH
REMOVAL
(1) Open hood, disconnect and isolate the battery
negative cable.
(2) Open right door.
(3) Open glove box.
(4) Reach up behind instrument panel and discon-
nect the glove box lamp switch electrical connector.
(5) Using a trim stick (special tool #C-4755) or
equivalent, gently pry out glove box lamp switch
from glove box opening surround (Fig. 5).
(6) If replacing the lamp, pull straight out of glove
box lamp switch.
Fig. 3 DOOR COURTESY LAMP UNIT - FRONT - REMOVE/INSTALL
1 - FRONT DOOR TRIM PANEL
3 - DOOR COURTESY LAMP UNIT CONNECTOR
2 - FRONT DOOR PANEL
4 - DOOR COURTESY LAMP UNIT
Fig. 4 DOOR COURTESY LAMP UNIT - REMOVE/
INSTALL
1 - DOOR COURTESY LAMP UNIT CONNECTOR
2 - FRONT DOOR TRIM PANEL
3 - DOOR COURTESY LAMP UNIT
CS
LAMPS/LIGHTING - INTERIOR
8L - 29
DOOR COURTESY LAMP UNIT (Continued)
INSTALLATION
(1) If replacing the lamp, push straight into glove
box lamp switch.
(2) Position lamp switch over retaining hole and
firmly snap into place (Fig. 5).
(3) Reach up behind instrument panel, and con-
nect the electrical connector.
(4) Close glove box.
(5) Close right door.
(6) Connect the battery negative cable.
(7) Close hood.
(8) Verify vehicle and system operation.
ILLUMINATION LAMPS
REMOVAL
The Instrument Panel Switch Pod has two illumi-
nation lamps (Fig. 6). If found to be faulty, the entire
cluster bezel must be removed. The Light Emitting
Diodes (LED’s) are serviceable by turning 1/4 turn
counterclockwise to remove. The cluster bezel must
first be removed to service the LED’s (Refer to 23 -
BODY/INSTRUMENT PANEL/CLUSTER BEZEL -
REMOVAL).
INSTALLATION
(1) Place Light Emitting Diode (LED) into lamp
opening in instrument panel switch pod.
(2) Turn 1/4 turn clockwise.
(3) Install Cluster bezel (Refer to 23 - BODY/IN-
STRUMENT PANEL/CLUSTER BEZEL - INSTAL-
LATION).
(4) Verify vehicle and system operation.
LIFTGATE LAMP
REMOVAL
(1) Open hood, disconnect and isolate the battery
negative cable.
(2) Open liftgate.
(3) Using a trim stick (special tool #C-4755) or
equivalent, gently pry out on door courtesy lamp lens
and remove from trim panel (Fig. 7).
(4) Gently pry up on the edge of the lamp and pull
out of the liftgate lamp unit to remove (Fig. 8).
Fig. 5 GLOVE BOX LAMP SWITCH - REMOVE/
INSTALL
1 - GLOVE BOX LAMP SWITCH
2 - GLOVE BOX LAMP SWITCH CONNECTOR
3 - INSTRUMENT PANEL
4 - GLOVE BOX OPENING
Fig. 6 INSTRUMENT PANEL SWITCH POD
ILLUMINATION
1 - INSTRUMENT PANEL SWITCH POD ILLUMINATION
Fig. 7 LIFTGATE LAMP LENS - REMOVAL
1 - LIFTGATE TRIM PANEL
2 - LIFTGATE LAMP UNIT LENS
3 - TRIM STICK (SPECIAL TOOL #C-4755)
8L - 30
LAMPS/LIGHTING - INTERIOR
CS
GLOVE BOX LAMP SWITCH (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст