Chrysler Pacifica. Manual — part 228
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Power Mirror connector.
Turn the ignition on.
Measure the Driver Mirror Vertical Driver circuit to ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Driver Mirror Vertical Driver circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.
909
POWER MIRROR
DRIVER MIRROR VERTICAL OUTPUT SHORT TO GROUND - DDM —
Continued
Symptom:
DRIVER MIRROR VERTICAL SENSOR CIRCUIT OPEN - DDM
When Monitored and Set Condition:
DRIVER MIRROR VERTICAL SENSOR CIRCUIT OPEN - DDM
When Monitored:
Continuously.
Set Condition:
If the voltage on the Driver Mirror Vertical Position Signal circuit is above
4.1 volts for over 10 seconds, this code will set.
POSSIBLE CAUSES
DRIVER MIRROR SENSOR GROUND WIRE OPEN
DRIVER MIRROR VERTICAL POSITION WIRE SHORTED TO VOLTAGE
STORED DIAGNOSTIC TROUBLE CODE
DRIVER MIRROR VERTICAL POSITION SIGNAL OPEN
DRIVER POWER MIRROR
DRIVER DOOR MODULE - SENSOR GROUND
DRIVER DOOR MODULE - VERTICAL POSITION SIGNAL
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase the DTC from Driver Door Module.
Operate the driver’s power mirror and memory system.
Turn the ignition switch to the Off position then start the engine and let run for one
minute.
With the DRBlll
t check for the same DTC to return in the DDM.
Did the same DTC return?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the Driver Power Mirror connector.
Turn the ignition on.
Measure the voltage of the Driver Mirror Vertical Position Signal circuit in the Driver
Power Mirror harness connector.
Is the voltage between 4.5 and 5.5 volts?
All
Yes
→ Go To 3
No
→ Go To 6
910
POWER MIRROR
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Driver Power Mirror connector.
Measure the resistance of the Driver Mirror Sensor Ground circuit in the harness
connector to ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Go To 5
4
If there are no possible causes remaining, view repair.
All
Repair
Replace the Driver Power Mirror.
Perform BODY VERIFICATION TEST - VER 1.
5
Turn the ignition off.
Disconnect the Driver Power Mirror connector.
Disconnect the Driver Door Module C3 connector.
Measure the resistance of Driver Mirror Sensor Ground circuit between the Driver
Door Module connector and the Driver Power Mirror connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the open Sensor Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.
6
Turn the ignition off.
Disconnect the Driver Power Mirror connector.
Disconnect the Driver Door Module C3 connector.
Turn the ignition on.
Measure the voltage of Driver Mirror Vertical Position Signal circuit.
Is there any voltage present?
All
Yes
→ Repair the Driver Mirror Vertical Position Signal circuit for a
short to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 7
7
Turn the ignition off.
Disconnect the Driver Door Module C3 connector.
Disconnect the Driver Power Mirror connector.
Measure the resistance of the Driver Mirror Vertical Position Signal circuit from the
driver power mirror connector to the Driver Door Module connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the open Driver Mirror Vertical Position Signal wire.
Perform BODY VERIFICATION TEST - VER 1.
911
POWER MIRROR
DRIVER MIRROR VERTICAL SENSOR CIRCUIT OPEN - DDM —
Continued
Symptom:
DRIVER MIRROR VERTICAL SENSOR CIRCUIT SHORT - DDM
When Monitored and Set Condition:
DRIVER MIRROR VERTICAL SENSOR CIRCUIT SHORT - DDM
When Monitored:
Continuously.
Set Condition:
If the voltage on the Driver Vertical Position Signal circuit is below 0.1 volt
for over 10 seconds, this code will set.
POSSIBLE CAUSES
DDM - VERTICAL POSITION LOW
STORED DIAGNOSTIC TROUBLE CODE
DRIVER MIRROR VERTICAL POSITION SIGNAL WIRE SHORT TO GROUND
DRIVER POWER MIRROR
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase the DTC from Driver Door Module.
Operate the driver’s power mirror and memory system.
Turn the ignition switch to the Off position then start the engine and let run for one
minute.
With the DRBlll
t check for the same DTC to return in the DDM.
Did the same DTC return?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the Driver Power Mirror connector.
Turn the ignition on.
Measure the voltage of the Driver Mirror Vertical Position Signal circuit in the Driver
Power Mirror harness connector.
Is the voltage between 4.5 and 5.5 volts?
All
Yes
→ Replace the Driver Power Mirror.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
912
POWER MIRROR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст