Chrysler Pacifica. Manual — part 229
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Driver Door Module C3 connector.
Disconnect the Driver Power Mirror connector.
Measure the resistance of the Driver Mirror Vertical Position Signal circuit to ground
at the Driver Power Mirror harness side connector.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Driver Mirror Vertical Position Signal wire for a short
to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.
913
POWER MIRROR
DRIVER MIRROR VERTICAL SENSOR CIRCUIT SHORT - DDM —
Continued
Symptom:
MIRROR ADJUSTING SWITCH STUCK - DDM
When Monitored and Set Condition:
MIRROR ADJUSTING SWITCH STUCK - DDM
When Monitored:
Continuously.
Set Condition:
If the switch is held down for over 15 seconds, this code will set.
POSSIBLE CAUSES
DTC PRESENT
DRIVER DOOR MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Cycle the ignition switch from Off to Run.
Check for any possible obstructions with the switch and correct if necessary.
Operate the Mirror Adjusting Switch several times.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display MIRROR ADJUSTING SWITCH STUCK?
All
Yes
→ Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ The condition that caused this code to set is not present at this
time. Operate the switch several times to ensure it does not stick.
If the switch ever sticks, replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.
914
POWER MIRROR
Symptom:
PASSENGER MIRROR COMMON OUTPUT SHORT TO BATTERY -
PDM
When Monitored and Set Condition:
PASSENGER MIRROR COMMON OUTPUT SHORT TO BATTERY - PDM
When Monitored:
Whenever mirror is idle.
Set Condition:
Driver circuit is shorted to battery.
POSSIBLE CAUSES
DTC PRESENT
POWER MIRROR
PASSENGER MIRROR COMMON DRIVER SHORTED TO VOLTAGE
PASSENGER DOOR MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase DTCs.
Cycle the ignition switch Off then back On.
With the DRBIII
t, read DTCs.
Did the same DTC return?
All
Yes
→ Go To 2
No
→ The conditions required to set the code are currently not present.
Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the power mirror connector.
Using the DRBIII
t, erase DTC’s.
Turn the ignition on.
Cycle the ignition switch Off then back On.
With the DRBIII
t, read DTC’s.
Did the same DTC return?
All
Yes
→ Go To 3
No
→ Inspect the power mirror harness for a short, if OK replace the
mirror.
Perform BODY VERIFICATION TEST - VER 1.
915
POWER MIRROR
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Power Mirror connector.
Turn the ignition on.
Measure the voltage of the Passenger Mirror Common Driver circuit.
Is the voltage above 1.0 volts?
All
Yes
→ Repair the Passenger Mirror Common Driver circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Passenger Door Module.
Perform BODY VERIFICATION TEST - VER 1.
916
POWER MIRROR
PASSENGER MIRROR COMMON OUTPUT SHORT TO BATTERY - PDM
—
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст