Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 1529
25. Push the camshaft (5) out of the back of the cyl-
inder head approximately 3.5 inches and remove
the right cam gear.
26. Remove the inner timing cover to cylinder head
retaining bolts.
27. Remove the cylinder head bolts in REVERSE of
tightening sequence.
28. Remove the cylinder head.
29. Clean and inspect all mating surfaces.
LEFT CYLINDER HEAD
1. Perform the fuel relief procedure.
2. Disconnect the negative battery cable.
3. Drain cooling system (Refer to 7 - COOLING -
STANDARD PROCEDURE).
4. Remove the upper intake manifold.
5. Remove the lower intake manifold (Refer to 9 -
ENGINE/MANIFOLDS/INTAKE
MANIFOLD
-
REMOVAL).
6. Remove the accessory drive belt (6).
7. Remove the belt tensioner (1).
8. Remove the accessory drive idler pulley.
9. Remove the power steering mounting bolts and set
pump (2) aside.
10. Remove the crankshaft damper (4) (Refer to 9 -
ENGINE/ENGINE BLOCK/VIBRATION DAMPER -
REMOVAL.
11. Remove the lower outer timing belt cover.
12. Raise and support the vehicle.
9 - 2140
ENGINE - 3.5L - SERVICE INFORMATION
LX
13. Remove the front exhaust pipe to exhaust mani-
fold mounting nuts (2).
14. Disconnect both oxygen sensor harness connec-
tors (1,2).
15. Lower the vehicle.
16. Remove the outer timing belt cover (Refer to 9 - ENGINE/VALVE TIMING/TIMING BELT / CHAIN COVER(S) -
REMOVAL).
TIMING GEAR ALIGNMENT
1 - RIGHT CAMSHAFT GEAR ALIGNMENT MARK
7 - LEFT CAMSHAFT GEAR
2 - RIGHT CAMSHAFT GEAR
8 - LEFT CAMSHAFT GEAR ALIGNMENT MARK
3 - CYLINDER HEAD TO INNER TIMING BELT COVER BOLTS -
RIGHT
9 - CRANKSHAFT GEAR ALIGNMENT MARK
4 - TIMING BELT
10 - CRANKSHAFT GEAR
5 - WATER PUMP PULLEY
11 - TIMING BELT TENSIONER PULLEY
6 - CYLINDER HEAD TO INNER TIMING BELT COVER BOLTS -
LEFT
12 - TIMING BELT TENSIONER
LX
ENGINE - 3.5L - SERVICE INFORMATION
9 - 2141
17. Rotate the engine to TDC and align the timing marks (1,8,9).
18. Remove the timing belt tensioner (12), timing belt (4), then reset tensioner. (Refer to 9 - ENGINE/VALVE TIM-
ING/TMNG BELT/CHAIN TENSIONER&PULLEY - REMOVAL)
19. Remove the left cylinder head cover to cylinder
head ground strap (3).
20. Remove the left cylinder head cover.
21. Remove the left rocker arm assembly (2).
9 - 2142
ENGINE - 3.5L - SERVICE INFORMATION
LX
22. Remove the left camshaft thrust plate (1).
23. Counterhold the left cam gear and remove the
cam gear retaining bolt. (Refer to 9 - ENGINE/
VALVE
TIMING/TIMING
BELT/CHAIN
AND
SPROCKETS - REMOVAL)
24. Push the camshaft out of the back of the cylinder
head approximately 3.5 inches and remove the
cam gear.Remove the front timing belt housing to
cylinder head bolts.
25. Remove the cylinder head bolts in REVERSE of
tightening sequence.
26. Remove the cylinder head.
27. Clean and inspect all mating surfaces.
.
LX
ENGINE - 3.5L - SERVICE INFORMATION
9 - 2143
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст