Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 1518
BEARING -CONNECTING ROD
CONNECTING RODS AND BEARINGS . . . . . 2189
CRANKSHAFT
BEARING -CRANKSHAFT MAIN
CRANKSHAFT MAIN BEARING FITTING . . . . 2197
SEAL -CRANKSHAFT OIL FRONT
SEAL - CRANKSHAFT OIL REAR
PLATE - FLEX
ROD - PISTON & CONNECTING
FITTING PISTONS . . . . . . . . . . . . . . . . . . . . . . . . 2208
RING - PISTON
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2213
STANDARD PROCEDURE
PISTON RING FITTING . . . . . . . . . . . . . . . . . . . . 2213
DAMPER - CRANKSHAFT
ENGINE MOUNTING
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2220
MOUNT -LEFT
MOUNT LEFT - AWD
MOUNT - RIGHT
MOUNT RIGHT - AWD
MOUNT - REAR
LUBRICATION
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2229
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2230
DIAGNOSIS AND TESTING
CHECKING ENGINE OIL PRESSURE . . . . . . . 2231
OIL
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2232
STANDARD PROCEDURE
COOLER-ENGINE OIL
FILTER -OIL
PAN - OIL
SWITCH-OIL PRESSURE SENSOR
PUMP - OIL
MANIFOLD - INTAKE
MANIFOLD-EXHAUST LEFT
LEFT EXHAUST MANIFOLD . . . . . . . . . . . . . . . 2265
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2266
INSTALLATION
LEFT EXHAUST MANIFOLD . . . . . . . . . . . . . . . 2266
MANIFOLD-EXHAUST RIGHT
RIGHT EXHAUST MANIFOLD . . . . . . . . . . . . . . 2267
RIGHT EXHAUST MANIFOLD . . . . . . . . . . . . . . 2268
VALVE TIMING
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2269
COVER-FRONT TIMING BELT
COVER-REAR TIMING BELT
9 - 2096
ENGINE - 3.5L - SERVICE INFORMATION
LX
BELT-TIMING AND SPROCKETS
CRANKSHAFT SPROCKET . . . . . . . . . . . . . . . . 2281
TENSIONER - TIMING BELT & PULLEY
LX
ENGINE - 3.5L - SERVICE INFORMATION
9 - 2097
ENGINE - 3.5L - SERVICE INFORMATION
DESCRIPTION
3.5L
The 3.5 Liter (214 Cubic Inches) 60°V-6 engine is a single overhead camshaft design with hydraulic lifters and four
valves per cylinder. The engine does not have provisions for a free wheeling valve train.
The cylinders are numbered from front to rear, with
the right bank odd numbered, and the left bank even
numbered. The firing order is 1–2–3–4–5–6.
9 - 2098
ENGINE - 3.5L - SERVICE INFORMATION
LX
The engine identification number (2) is located on the
rear of engine block just below the left cylinder head
(1).
DIAGNOSIS AND TESTING
INTRODUCTION
Engine diagnosis is helpful in determining the causes of malfunctions not detected and remedied by routine main-
tenance.
These malfunctions may be classified as either mechanical (e.g., a strange noise), or performance (e.g., engine
idles rough and stalls).
Refer to (Service Diagnosis - Mechanical Chart) and (Service Diagnosis - Performance Chart), for possible causes
and corrections of malfunctions. Refer to FUEL SYSTEM for the fuel system diagnosis.
Additional tests and diagnostic procedures may be necessary for specific engine malfunctions that cannot be iso-
lated with the Service Diagnosis charts. Information concerning additional tests and diagnosis is provided within the
following:
•
Cylinder Compression Pressure Test
•
Cylinder Combustion Pressure Leakage Test
•
Cylinder Head Gasket Failure Diagnosis
•
Intake Manifold Leakage Diagnosis
•
Lash Adjuster (Tappet) Noise Diagnosis
•
Engine Oil Leak Inspection
LX
ENGINE - 3.5L - SERVICE INFORMATION
9 - 2099
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст