Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2127

8. Position the two locator pins (4) on the back of the

trim panel (2) to the locator holes (3) on the inside
of the door panel and simultaneously push the
three upper pins (1) into the grommet plugs near
the top of the door. Make certain that the upper
edges of the trim panel are engaged in the grooves
of the window moldings.

9. Install and tighten the screw (4) that secures the

interior remote handle recess of the trim panel (2)
to the inside of the door (1). Tighten the screw to 2
N·m (16 in. lbs.). Fold and snap the screw cap over
the screw.

10. Install and tighten the screw (5) that secures the

trim panel (2) to the pull cup bracket below the
trim panel pull cup. Tighten the screw to 2 N·m
(16 in. lbs.). Fold and snap the screw cap over
the screw.

11. Install the three push-pin retainers (1) that secure

the trim panel to the inside of the door. (Refer to
23 - BODY/DOOR - FRONT - DESCRIPTION -
FASTENERS).

12. Install and tighten the four screws (6) that secure

the bottom and front lower corner of the trim
panel to the inside of the door. Tighten the screws
to 2 N·m (16 in. lbs.).

NOTE: For vehicles equipped with the optional
Automatic Express Up power window feature, cal-
ibration of this feature is required whenever power
to the door module is disrupted. A battery recon-
nect procedure must be performed anytime the
battery has been disconnected. (Refer to 8 - ELEC-
TRICAL/BATTERY SYSTEM - STANDARD PROCE-
DURE).

13. Reconnect the battery negative cable.

23 - 56

DOOR - FRONT

LX

WATERSHIELD

REMOVAL

CAUTION: Do not allow the watershield or adhe-
sive to become contaminated with dirt or other
foreign substances.

Do not damage the watershield during removal
and installation.

If the watershield becomes contaminated or dam-
aged, replace the watershield.

1. Remove the trim panel from the inside of the front

door. (Refer to 23 - BODY/DOOR - FRONT/TRIM
PANEL - REMOVAL).

2. Carefully separate the lower half of the watershield

(2) from the inside of the door (1).

3. Lift the lower half of the watershield upward far

enough to access and pull the trim panel take outs
of the door wire harness out of the slit near the
center of the watershield.

4. Carefully separate the upper half of the watershield

from the inside of the door.

5. Lift the upper half of the watershield upward far enough to disengage the inside latch lock knob and link and the

inside remote latch release handle link from the slit near the upper rear corner of the watershield.

6. Remove the watershield from the door.

INSTALLATION

CAUTION: Do not allow the watershield or adhe-
sive to become contaminated with dirt or other
foreign substances.

Do not damage the watershield during removal
and installation.

If the watershield becomes contaminated or dam-
aged, replace the watershield.

1. Thread the inside latch lock knob and link and the

inside remote latch release handle link through the
slit near the upper rear corner of the watershield
(2).

2. Place the front and rear dimple formations located

in the upper watershield into their respective loca-
tor holes in the door (1) inner panel.

3. Apply firm and even pressure to the adhesive bead

along the upper edge of the watershield to seal it
to the inside of the door.

4. Lift the lower half of the watershield upward far enough to access and pull the trim panel take outs of the door

wire harness out of through the slit near the center of the watershield.

5. Apply firm and even pressure to the adhesive bead along the remaining edges of the watershield to seal it to the

inside of the door. Be certain that the watershield is sealed to the inside of the door.

6. Reinstall the trim panel onto the inside of the front door. (Refer to 23 - BODY/DOOR - FRONT/TRIM PANEL -

INSTALLATION).

LX

DOOR - FRONT

23 - 57

WINDOW REGULATOR

REMOVAL

1. Remove the trim panel from the inside of the front

door. (Refer to 23 - BODY/DOOR - FRONT/TRIM
PANEL - REMOVAL).

2. Remove the speaker from the inside of the front

door. (Refer to 8 - ELECTRICAL/AUDIO/SPEAKER
- REMOVAL).

3. Remove the watershield from the inside of the front

door. (Refer to 23 - BODY/DOOR - FRONT/WA-
TERSHIELD - REMOVAL).

4. Remove the screw (3) that secures the bottom of

the pull cup bracket (2) and the bottom of the win-
dow regulator rear rail to the inside of the front
door.

5. Loosen the screw (1) that secures the top of the

pull cup bracket to the inside of the front door.

6. Disengage the upper pull cup bracket screw from

the keyed hole and remove the bracket from the
inside of the front door.

7. Using the regulator, adjust the front door glass (1)

position up or down as required for access to the
two window regulator glass clamps (3).

8. Loosen the screw (2) in each of the glass clamps

far enough to release the glass.

9. Lift the glass out of the regulator clamps and into

its full up position, then tape the glass securely into
place.

23 - 58

DOOR - FRONT

LX

10. Remove the two screws (6) that secure the bot-

tom of the front regulator rail (5) and the regulator
motor support bracket (4) to the inside of the
door.

11. Loosen the two screws (2) that secure the tops of

both regulator rails to the keyed holes (1) on the
inside of the door.

12. Lift the front regulator rail upward within the door

far enough to disengage the screw from the
keyed hole in the door.

13. Lower the front regulator rail within the door (1)

far enough to access and disconnect the door
wire harness connector (4) from the regulator
motor (2) through the speaker mounting hole (3)
on the inside of the door near the front.

14. Lift the rear regulator rail upward within the door

far enough to disengage the screw from the
keyed hole in the door.

15. Remove the regulator through the large access

hole on the inside of the door near the rear.

LX

DOOR - FRONT

23 - 59