Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2125
4. For the driver side front door only, reach into the
back of the door shell to engage the lock cylinder
actuator link (2) to the latch lever and snap the
plastic clip over the link to secure it to the latch (3).
5. Reach into the back of the door shell to engage the
exterior door handle latch release link (1) to the
latch lever and snap the plastic clip over the link to
secure it to the latch.
6. Reach into the back of the door shell to engage the
end of the interior door handle latch release link (4)
to the latch lever and snap the plastic clip over the
link to secure it to the latch.
7. Position the interior door latch lock link and knob
unit (2) into the front door (1).
23 - 48
DOOR - FRONT
LX
8. Reach into the back of the door shell to engage the
end of the interior door latch lock link (1) to the
latch lever and snap the plastic clip over the link to
secure it to the latch (2).
9. With the upper screw (1) hand-started into the pull
cup bracket (2), position the screw into the keyed
hole on the inside of the front door.
10. Install and tighten the screw (3) that secures the
bottom of the pull cup bracket and the bottom of
the window regulator rear rail to the inside of the
front door. Tighten the screw to 11 N·m (100 in.
lbs.).
11. Tighten the screw that secures the top of the pull
cup bracket to the inside of the front door. Tighten
the screw to 10 N·m (90 in. lbs.).
12. Reinstall the watershield onto the inside of the
front door. (Refer to 23 - BODY/DOOR - FRONT/
WATERSHIELD - INSTALLATION).
13. Reinstall the speaker onto the inside of the front
door.
(Refer
to
8
-
ELECTRICAL/AUDIO/
SPEAKER - INSTALLATION).
14. Reinstall the trim panel onto the inside of the front
door. (Refer to 23 - BODY/DOOR - FRONT/TRIM
PANEL - INSTALLATION).
15. Use a wrench inserted through the access slot on
the outer latch face of the front door shell (1) to
loosen the hex socket latch release adjusting
screw (3) on the latch (2).
16. Cycle the door outside latch release handle
through its full travel two or three times.
17. Tighten the adjusting screw.
LX
DOOR - FRONT
23 - 49
LOCK CYLINDER
REMOVAL
NOTE: A door lock cylinder is used only on the
driver side front door exterior handle.
1. Remove the handle (1) from the outside of the
driver side front door. (Refer to 23 - BODY/DOOR -
FRONT/EXTERIOR HANDLE - REMOVAL).
2. Using hand pressure, push on the face of the lock
cylinder (2) until it pops out of the cavity in the
back of the door handle.
INSTALLATION
NOTE: A door lock cylinder is used only on the
driver side front door exterior handle.
1. Insert the lock cylinder (2) into the cavity on the
back of the door handle (1).
2. Align the lock cylinder in the handle by engaging
the tab (3) on the outer circumference of the cylin-
der in the slot of the tab (4) on the wall of the han-
dle cavity.
3. Reinstall the handle onto the outside of the driver
side front door. (Refer to 23 - BODY/DOOR -
FRONT/EXTERIOR HANDLE - INSTALLATION).
23 - 50
DOOR - FRONT
LX
STRIKER
REMOVAL
1. Open the front door.
2. Mark the front door latch striker (3) location on the
face of the outer B-pillar (1) to aid reinstallation.
3. Remove the two screws (2) that secure the striker
to the B-pillar.
4. Remove the striker from the B-pillar.
INSTALLATION
1. Position the front door latch striker (3) on the face
of the outer B-pillar (1).
2. Install and tighten the two screws (2) that secure
the striker to the B-pillar. Tighten the screws to 33
N·m (24 ft. lbs.).
3. Adjust the latch striker position as necessary to
achieve proper door spacing and latch operation.
LX
DOOR - FRONT
23 - 51
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст