Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 273
3.
CHECK THE (X209) AMPLIFIED LEFT I/P SPEAKER (+) CIRCUIT FOR AN OPEN
Turn the ignition off.
Disconnect the Amplifier C2 harness connector.
Measure the resistance of the (X209) Amplified Left I/P Speaker (+) cir-
cuit between the Amplifier C2 harness connector and the Amplified Left
I/P Speaker harness connector.
Is the resistance below 5.0 ohms?
Yes
>> Go To 4
No
>> Repair the (X209) Amplified Left I/P Speaker (+) circuit for
an open.
Perform BODY VERIFICATION TEST VER-1.
4.
CHECK THE (X299) AMPLIFIED LEFT I/P SPEAKER (-) CIRCUIT FOR AN OPEN
Turn the ignition off.
Disconnect the Amplifier C2 harness connector.
Measure the resistance of the (X299) Amplified Left I/P Speaker (-) cir-
cuit between the Amplifier C2 harness connector and the Amplified Left
I/P Speaker harness connector.
Is the resistance below 5.0 ohms?
Yes
>> Replace the Amplifier in accordance with the service infor-
mation.
Perform BODY VERIFICATION TEST VER-1.
No
>> Repair the (X299) Amplified Left I/P Speaker (-) circuit for
an open.
Perform BODY VERIFICATION TEST VER-1.
8A - 18
AUDIO - ELECTRICAL DIAGNOSTICS
LX
B1464-CHANNEL 1 AUDIO SPEAKER OUTPUT CIRCUIT SHORTED TOGETHER
For a complete wiring diagram Refer to Section 8W.
LX
AUDIO - ELECTRICAL DIAGNOSTICS
8A - 19
•
When Monitored:
•
With the ignition on. Radio volume at 25 or higher.
•
Set Condition:
•
The amplifier detects that the output circuits are shorted together.
Possible Causes
(X209) AMPLIFIED LEFT I/P SPEAKER (+) CIRCUIT SHORTED TO THE (X299) AMPLIFIED LEFT I/P SPEAKER
(-) CIRCUIT
AMPLIFIED LEFT I/P SPEAKER
AMPLIFIER
Diagnostic Test
1.
CHECK FOR AN INTERMITTENT CONDITION
Turn the ignition on, then off, and then on again.
With the scan tool, erase Amplifier DTCs.
Turn the radio on.
Turn the volume level to 25.
With the scan tool, read Amplifier DTCs.
Does the scan tool display active: B1464-CHANNEL 1 AUDIO SPEAKER OUTPUT CIRCUIT SHORTED
TOGETHER?
Yes
>> Go To 2
No
>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-
matic as a guide, inspect the wiring and connectors.
Perform BODY VERIFICATION TEST VER-1.
2.
CHECK THE OPERATION OF THE AMPLIFIED LEFT I/P SPEAKER
Disconnect the Amplified Left I/P Speaker.
Measure the resistance of the speaker between the two terminals.
Is the resistance of the speaker less than 1 ohm?
Yes
>> Replace the Amplified Left I/P Speaker in accordance with the service information.
Perform BODY VERIFICATION TEST VER-1.
No
>> Go To 3
8A - 20
AUDIO - ELECTRICAL DIAGNOSTICS
LX
3.
CHECK THE (X209) AMPLIFIED LEFT I/P SPEAKER (+) CIRCUIT, AND THE (X299) AMPLIFIED LEFT I/P
SPEAKER (-) CIRCUITS FOR A SHORT TOGETHER
Turn the ignition off.
Disconnect the Amplifier C2 harness connector.
Measure the resistance between the (X209) Amplified Left I/P Speaker
(+) circuit, and the (X299) Amplified Left I/P Speaker (-) circuit.
Is the resistance below 10K ohms?
Yes
>> Repair the (X209) Amplified Left I/P Speaker (+) circuit, and
the (X299) Amplified Left I/P Speaker (-) circuit for a short
together.
Perform BODY VERIFICATION TEST VER-1.
No
>> Replace the Amplifier in accordance with the service infor-
mation.
Perform BODY VERIFICATION TEST VER-1.
LX
AUDIO - ELECTRICAL DIAGNOSTICS
8A - 21
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст