Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2167
LIFTGATE
REMOVAL
1. Open the liftgate (7).
2. Disconnect and isolate the battery negative cable.
3. Remove the upper and lower trim panels from the
inside of the liftgate. (Refer to 23 - BODY/DECK-
LID/HATCH/LIFTGATE/TAILGATE/TRIM PANEL -
REMOVAL).
4. Disconnect the washer supply hose (2) in the right
body wire harness (3) from the liftgate spoiler
washer nozzle hose on the underside of the lift-
gate.
5. Disconnect the take out and connector (1) of the
right body wire harness from the antenna amplifier
module on the inside of the liftgate near the right
upper corner of the glass opening.
6. Disconnect the two connectors (6) of the liftgate
wire harness from the two take outs and connec-
tors of the left body wire harness (5).
7. Disengage the retainers that secure the liftgate
take outs of the right and left body wire harnesses to the underside of the liftgate.
8. Disengage the wire grommets (4) of the right and left body wire harnesses inboard of the liftgate hinges from the
underside of the liftgate.
9. Carefully remove the liftgate take outs of the right and left body wire harnesses from between the inner and outer
liftgate panels.
10. Disconnect the gas props from the ball studs on
each side of the liftgate (2). (Refer to 23 - BODY/
DECKLID/HATCH/LIFTGATE/TAILGATE/GAS
PROP - REMOVAL).
11. Remove the trim plate from the underside of the
upper liftgate opening header (3). (Refer to 23 -
BODY/INTERIOR/LIFTGATE OPENING UPPER
TRIM - REMOVAL).
12. Mark the liftgate hinge body bracket (1) locations
on the upper liftgate opening header to aid rein-
stallation.
13. Carefully pull the rear edge of the headliner down-
ward from the header far enough to access and
remove the four nuts (4) that secure the two studs
of each hinge to the underside of the header.
14. With the aid of an assistant, lift the liftgate far
enough to disengage the hinge studs from the
header and remove the liftgate from the vehicle.
23 - 216
LIFTGATE
LX
INSTALLATION
1. With the aid of an assistant, support and position
the liftgate (2) with the studs of the two hinge body
half brackets (1) inserted into the holes of the
upper liftgate opening header (3) on the vehicle.
2. Carefully pull the rear edge of the headliner down-
ward from the header far enough to install and
tighten the four nuts (4) that secure the hinge studs
to the underside of the header. Tighten the nuts to
28 N·m (21 ft. lbs.).
3. Reinstall the gas props to the ball studs on each
side of the liftgate. (Refer to 23 - BODY/DECKLID/
HATCH/LIFTGATE/TAILGATE/GAS
PROP
-
INSTALLATION).
4. Remove the fixture being used to support the lift-
gate for service.
5. Carefully route the liftgate take outs of the right (3)
and left (5) body wire harnesses between the inner
and outer panels of the liftgate (7).
6. Engage the wire grommets (4) of the right and left
body wire harnesses into the holes inboard of the
liftgate hinges on the underside of the liftgate.
7. Engage the retainers that secure the liftgate take
outs of the right and left body wire harnesses to
the underside of the liftgate.
8. Reconnect the two connectors (6) of the liftgate
wire harness to the two take outs and connectors
of the left body wire harness.
9. Reconnect the take out and connector (1) of the
right body wire harness to the antenna amplifier
module on the inside of the liftgate near the right
upper corner of the glass opening.
10. Reconnect the washer supply hose (2) in the right
body wire harness to the liftgate spoiler washer
nozzle hose on the underside of the liftgate.
11. Adjust the liftgate hinge, bumper, latch and latch striker positions as necessary to achieve proper spacing and
operation.
12. Reinstall the trim plate onto the upper liftgate opening header. (Refer to 23 - BODY/INTERIOR/LIFTGATE
OPENING UPPER TRIM - INSTALLATION).
13. Reinstall the upper and lower trim panels onto the inside of the liftgate. (Refer to 23 - BODY/DECKLID/HATCH/
LIFTGATE/TAILGATE/TRIM PANEL - INSTALLATION).
14. Reconnect the battery negative cable.
15. Close the liftgate.
LX
LIFTGATE
23 - 217
TRIM PANEL
REMOVAL
LOWER
1. Disconnect and isolate the battery negative cable.
2. Remove the lamp from the lower liftgate trim panel.
3. Remove the two screws (6) within the pull cup formation to the right of the latch that secure the lower trim panel
(1) to the inside of the liftgate (4).
4. Using a trim stick or another suitable wide flat-bladed tool, carefully pry the trim panel away from the inside of
the liftgate to release the seven push-in plastic fasteners (7) that secure the panel to the liftgate.
5. Remove the liftgate lower trim panel from the vehicle.
23 - 218
LIFTGATE
LX
REMOVAL
1. Open the liftgate (6).
2. Remove the lower trim panel from the inside of the liftgate. (Refer to 23 - BODY/DECKLID/HATCH/LIFTGATE/
TAILGATE/TRIM PANEL/LOWER - REMOVAL).
3. Remove the two screws (4) that secure the lower corners of the upper trim panel (3) to the inside of the liftgate.
4. Using a trim stick or another suitable wide flat-bladed tool, carefully pry the trim panel away from the inside of
the liftgate to release the push-in plastic fasteners that secure the panel to the liftgate.
5. Remove the liftgate upper trim panel from the vehicle.
LX
LIFTGATE
23 - 219
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст