Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2131
INSTALLATION
1. Position the upper (1) or lower (4) hinge to the
hinge face of the rear door (3).
2. Install and tighten the nut (5) that secures the
hinge to the stud (2) on the door. Tighten the nut to
28 N·m (21 ft. lbs.).
3. Install and tighten the screw (6) that secures the
hinge to the door. Tighten the screw to 28 N·m (21
ft. lbs.).
4. Position the upper (2) or lower (4) hinge bracket
onto the outside of the lower B-pillar (1).
5. Install and tighten the two screws (3) that secure
the hinge bracket to the outside of the lower B-pil-
lar. Tighten the screws to 30 N·m (22 ft. lbs.).
6. Reinstall the rear door onto the vehicle. (Refer to
23
-
BODY/DOOR
-
REAR/DOOR
-
INSTALLATION).
23 - 72
DOOR - REAR
LX
LATCH
REMOVAL
1. Remove the trim panel from the inside of the rear
door. (Refer to 23 - BODY/DOOR - REAR/TRIM
PANEL - REMOVAL).
2. Remove the watershield from the inside of the rear
door. (Refer to 23 - BODY/DOOR - REAR/WATER-
SHIELD - REMOVAL).
3. Remove the door glass channel and bracket from
the inside of the rear door. (Refer to 23 - BODY/
DOOR
-
REAR/GLASS
RUN
CHANNEL
-
REMOVAL).
4. Reach into the back of the door shell to unsnap the
plastic clip that secures the end of the interior door
latch lock link (1) to the latch lever and disengage
the link from the latch (2).
5. Remove the interior door latch lock link and knob
unit from the rear door.
6. Reach into the back of the door shell to unsnap the
plastic clip that secures the end of the interior door
handle latch release link (3) to the latch lever and
disengage the link from the latch.
7. Reach into the back of the door shell to unsnap the plastic clip that secures the end of the exterior door handle
latch release link (4) to the latch lever and disengage the link from the latch.
8. Remove the three screws (2) that secure the latch
(3) to the outer latch face of the rear door (1).
LX
DOOR - REAR
23 - 73
NOTE: Wiring connector can be disconnected
much easier after all links are disconnected from
latch and latch is unscrewed from door.
9. Reach into the back of the door shell (3) and pull
the latch forward far enough to access and discon-
nect the door wire harness connector (1) from the
front door latch (2).
10. Remove the latch from the interior of the door
shell.
INSTALLATION
NOTE: Wiring connector can be connected much
easier with all links disconnected from latch and
latch is unscrewed from door.
1. Connect the door wire harness connector (1) to the
door latch (2).
23 - 74
DOOR - REAR
LX
2. Position the latch (3) to the latch face on the inte-
rior of the rear door shell (1).
3. Install and tighten the three screws (2) that secure
the latch to the outer latch face of the rear door.
Tighten the screws to 12 N·m (108 in. lbs.).
4. Reach into the back of the door shell to engage the
exterior door handle latch release link (4) to the
latch (2) lever and snap the plastic clip over the
link to secure it to the latch.
5. Reach into the back of the door shell to engage the
end of the interior door handle latch release link (3)
to the latch lever and snap the plastic clip over the
link to secure it to the latch.
6. Position the interior door latch lock link and knob
unit (2) into the rear door (1).
7. Reach into the back of the door shell to engage the
end of the interior door latch lock link to the latch
lever and snap the plastic clip over the link to
secure it to the latch.
8. Reinstall the door glass channel and bracket to the
inside of the rear door. (Refer to 23 - BODY/DOOR
- REAR/GLASS RUN CHANNEL - INSTALLATION).
9. Reinstall the watershield onto the inside of the rear
door. (Refer to 23 - BODY/DOOR - REAR/WATER-
SHIELD - INSTALLATION).
10. Reinstall the trim panel onto the inside of the rear
door. (Refer to 23 - BODY/DOOR - REAR/TRIM
PANEL - INSTALLATION).
LX
DOOR - REAR
23 - 75
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст