Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 1659
22. Install the 5 front oil pan to timing cover bolts.
Tighten the bolts to 20 N·m (177 in. lbs.).
23. Install #9102 crankshaft lock (2) into the starter
access blank.
24. Lower the vehicle.
25. Install the vibration damper. Tighten the bolts to
200 N·m (148 ft. lbs.) and then an additional 90°.
9 - 2660
ENGINE - 3.0L TD SERVICE INFORMATION
LX
NOTE: Care must be taken not to get any engine
sealer on the camshaft journals.
26. Apply a 1.5mm continuous bead of Mopar Engine
Sealant RTV (1) around the diameter of the left
cylinder head cover, and install the cover with
new camshaft seals.
27. Tighten the bolts in three stages following the
sequence provided. First to 4 N·m (35 in. lbs.),
then to 6 N·m (53 in. lbs.), and then to 8.4 N·m
(75 in. lbs.).
28. Install the oil filter housing bracket. Tighten the
bolts to 13.8 N·m (122 in. lbs.).
29. Install the high pressure pump. Tighten bolts to
13.5 N·m (120 in. lbs.).
NOTE: Idler pulley bolts are L.H. thread.
30. Install the belt idler pulleys (1). Tighten the bolts
to 58 N·m (43 ft. lbs.).
31. Install the drive belt tensioner (2). Tighten the
bolts to 58 N·m (43 ft. lbs.).
32. Install the drive belt.
LX
ENGINE - 3.0L TD SERVICE INFORMATION
9 - 2661
CAUTION: The right intake manifold upper thermo-
stat housing bolts should be tightened to 8.4 N·m
(74 in. lbs.).
33. Install the intake manifold (4). Tighten bolts to 16
N·m (142 in. lbs.), starting in the middle and tight-
ening in a cross pattern outward until reaching the
upper thermostat bolts on the right front manifold.
34. Tighten the upper thermostat bolts on the right
cylinder head to 8.4 N·m (74 in.lbs.).
CAUTION: The fuel injector sealing washers MUST
be replaced. DO NOT use the old sealing washers
or double the sealing washers.
35. Lubricate the fuel injector body (1), install the left
fuel injectors (1) and new lower sealing washers.
36. Install the injector retaining claws and tighten the
bolts to 7 N·m plus 180 °(62 in. lbs. plus 180°).
37. Properly route and install the fuel return hoses (5)
and connect them to the injectors.
9 - 2662
ENGINE - 3.0L TD SERVICE INFORMATION
LX
38. Properly route and connect the engine harness.
39. Install the fuel rail (2). Tighten the bolts to 33 N·m
(24 ft. lbs.).
CAUTION: Inspect the fuel lines for wear or dam-
age, look closely around the flange area. Replace
as necessary. DO NOT over tighten.
40. Install the high pressure fuel lines, including the
fuel rail equalizing line. Tighten the line nuts to 27
N·m (20 ft. lbs.)
41. Install the fuel filter (2) and connect the harnesses
(1) and hoses (3).
LX
ENGINE - 3.0L TD SERVICE INFORMATION
9 - 2663
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст