Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2170
SEATS
TABLE OF CONTENTS
page
page
SEATS
RESTRAINT SYSTEM . . . . . . . . . . . . . . . . . . . . . . 229
ADJUSTERS-FRONT
ARMREST-REAR
CUSHION/COVER-CUSHION - FRONT
CUSHION/COVER-CUSHION - SECOND ROW
CUSHION/COVER-SEAT BACK - FRONT
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
CUSHION/COVER-SEAT BACK - SECOND ROW
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
INSTALLATION
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
RISER-FRONT
SEAT-FRONT
STRIKER-SEAT BACK LATCH - SECOND ROW
SUPPORT-LUMBAR
23 - 228
SEATS
LX
SEATS
WARNING
RESTRAINT SYSTEM
WARNING: During and following any seat belt or child restraint anchor service, carefully inspect all seat
belts, buckles, mounting hardware, retractors, tether straps, and anchors for proper installation, operation,
or damage. Replace any belt that is cut, frayed, or torn. Straighten any belt that is twisted. Tighten any
loose fasteners. Replace any belt that has a damaged or inoperative buckle or retractor. Replace any belt
that has a bent or damaged latch plate or anchor plate. Replace any child restraint anchor or the unit to
which the anchor is integral that has been bent or damaged. Never attempt to repair a seat belt or child
restraint component. Always replace damaged or faulty seat belt and child restraint components with the
correct, new and unused replacement parts listed in the DaimlerChrysler Mopar
T
parts catalog. Failure to
follow these instructions may result in personal injury or death.
WARNING: On vehicles equipped with airbags, disable the supplemental restraint system before attempting
any steering wheel, steering column, airbag, occupant classification system, seat belt tensioner, impact sen-
sor, or instrument panel component diagnosis or service. Disconnect and isolate the battery negative
(ground) cable, then wait two minutes for the system capacitor to discharge before performing further diag-
nosis or service. This is the only sure way to disable the supplemental restraint system. Failure to take the
proper precautions could result in accidental airbag deployment. Failure to follow these instructions may
result in personal injury or death.
WARNING: On vehicles equipped with airbags, before performing any welding operations disconnect and
isolate the battery negative (ground) cable and disconnect all wire harness connectors from the Airbag Con-
trol Module (ACM). Failure to take the proper precautions could result in accidental airbag deployment and
other possible damage to the supplemental restraint system circuits and components. Failure to follow
these instructions may result in personal injury or death.
WARNING: Replace all restraint system components only with parts specified in the DaimlerChrysler
Mopar
T
parts catalog. Substitute parts may appear interchangeable, but internal differences may result in
inferior occupant protection. Failure to follow these instructions may result in personal injury or death.
WARNING: The fasteners, screws, and bolts originally used for the restraint system components must never
be replaced with any substitutes. These fasteners have special coatings and are specifically designed for
the restraint system. Any time a new fastener is needed, replace it with the correct fasteners provided in the
service package or specified in the DaimlerChrysler Mopar
T
parts catalog. Failure to follow these instruc-
tions may result in personal injury or death.
WARNING: On vehicles equipped with the Occupant Classification System (OCS) do not hang any after mar-
ket devices from the front passengers seat back. Do not install a front drivers seat back cover with map
pocket onto the passenger seat. Failure to follow these instructions may result in personal injury or death.
WARNING: The Seat Weight Sensor is a sensitive, calibrated unit and must be handled carefully. Do not
drop or handle roughly. If dropped or damaged, replace with another sensor. Failure to follow these instruc-
tions may result in personal injury or death.
WARNING: The front passenger seat must be handled carefully as well. When removing the seat, be careful
when setting on floor not to drop. If dropped, the sensor may be inoperative. Failure to follow these instruc-
tions may result in personal injury or death.
LX
SEATS
23 - 229
WARNING: When the seat is on the floor, no one should sit in the front passenger seat. This uneven force
may damage the sensing ability of the seat weight sensors. If sat on and damaged, the sensor may be
inoperative. Failure to follow these instructions may result in personal injury or death.
23 - 230
SEATS
LX
ADJUSTERS-FRONT
REMOVAL
1. Before proceeding with the following repair procedure, review all warnings and cautions. (Refer to 23 - BODY/
SEATS - WARNING)
2. Remove the seat cushion as necessary. (Refer to 23 - BODY/SEATS/SEAT CUSHION / COVER - FRONT -
REMOVAL)
Power
1. Remove the seat risers. (Refer to 23 - BODY/
SEATS/SEAT RISER - FRONT - REMOVAL)
2. Remove the bolts and nuts (2 & 4) and separate
the height adjuster assembly from the length
adjuster assembly (3).
NOTE: Bolt (4) is a different size from the other
three bolts (2). Note the location for proper
installation.
WARNING: A seat structure that has seen signifi-
cant load may have the locking mechanism acti-
vated and may exhibit the following symptoms:
•
Locking pawl (2) loose
•
Locking pawl (2) engaged into the seat frame
side member (1)
•
Height adjuster only works on outboard side
•
Broken or missing shear pin (3)
If any one or more of these symptoms exist
replace the height adjuster assembly. Do not
attempt
any
repairs.
Failure
to
follow
these
instructions may result in personal injury or death.
LX
SEATS
23 - 231
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст