Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 269
OUTPUT CIRCUIT OPEN . . . . . . . . . . . . . . . . . . . 85
OUTPUT CIRCUIT SHORTED TOGETHER . . . 88
FRONT CONTROL MODULE . . . . . . . . . . . . . . . . 95
B1401-FRONT LEFT AUDIO SPEAKER
OUTPUT CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . 96
B1402-FRONT LEFT AUDIO SPEAKER
OUTPUT CIRCUIT HIGH. . . . . . . . . . . . . . . . . . . . 98
B1403-FRONT LEFT AUDIO SPEAKER
OUTPUT CIRCUIT OPEN . . . . . . . . . . . . . . . . . . 101
B1405-FRONT RIGHT AUDIO SPEAKER
OUTPUT CIRCUIT LOW . . . . . . . . . . . . . . . . . . . 103
B1406-FRONT RIGHT AUDIO SPEAKER
OUTPUT CIRCUIT HIGH. . . . . . . . . . . . . . . . . . . 105
B1407-FRONT RIGHT AUDIO SPEAKER
OUTPUT CIRCUIT OPEN . . . . . . . . . . . . . . . . . . 108
OUTPUT CIRCUIT LOW . . . . . . . . . . . . . . . . . . . 110
OUTPUT CIRCUIT HIGH . . . . . . . . . . . . . . . . . . . 112
OUTPUT CIRCUIT OPEN . . . . . . . . . . . . . . . . . . 115
B140D-REAR RIGHT AUDIO SPEAKER
OUTPUT CIRCUIT LOW . . . . . . . . . . . . . . . . . . . 117
B140E-REAR RIGHT AUDIO SPEAKER
OUTPUT CIRCUIT HIGH . . . . . . . . . . . . . . . . . . . 119
B140F-REAR RIGHT AUDIO SPEAKER
OUTPUT CIRCUIT OPEN . . . . . . . . . . . . . . . . . . 122
INOPERABLE DISC . . . . . . . . . . . . . . . . . . . . . . . 124
INOPERABLE DISC . . . . . . . . . . . . . . . . . . . . . . . 125
TEMPERATURE . . . . . . . . . . . . . . . . . . . . . . . . . . 126
8A - 2
AUDIO - ELECTRICAL DIAGNOSTICS
LX
AUDIO - ELECTRICAL DIAGNOSTICS
DIAGNOSIS AND TESTING
LX
AUDIO - ELECTRICAL DIAGNOSTICS
8A - 3
B210D-BATTERY VOLTAGE LOW
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on.
•
Set Condition:
•
If the module detects that the battery voltage is less than 9.0 volts for 1 second.
Possible Causes
VEHICLE CHARGING SYSTEM
AMPLIFIER
Diagnostic Test
1.
CHECK FOR AN INTERMITTENT CONDITION
Turn the ignition on, then off, and then on again.
With the scan tool, read Amplifier DTCs.
Does the scan tool display active: B210D-BATTERY VOLTAGE LOW?
Yes
>> Go To 2
No
>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-
matic as a guide, inspect the wiring and connectors.
Perform BODY VERIFICATION TEST VER-1.
2.
CHECK THE BATTERY VOLTAGE TO THE AMPLIFIER
With the scan tool in Data Display, read Amplifier battery voltage.
Is the battery voltage less than 9.0 volts?
Yes
>> Go To 3
No
>> Replace the Amplifier in accordance with the Service Information.
Perform OCS VERIFICATION TEST - VER 1.
3.
CHECK FOR CHARGING SYSTEM RELATED DTCs IN THE POWERTRAIN CONTROL MODULE (PCM)
With the scan tool in ECU View, select PCM and check for any Charging System related DTCs.
Does the scan tool display any Charging System related DTCs?
Yes
>> Diagnose and repair the DTCs. Refer to (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).
No
>> Replace the Amplifier in accordance with the Service Information.
Perform OCS VERIFICATION TEST - VER 1.
8A - 4
AUDIO - ELECTRICAL DIAGNOSTICS
LX
B210E-BATTERY VOLTAGE HIGH
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on.
•
Set Condition:
•
If the module detects that the battery voltage is greater 16.5 volts for 1 second.
Possible Causes
VEHICLE CHARGING SYSTEM
AMPLIFIER
Diagnostic Test
1.
CHECK FOR AN INTERMITTENT CONDITION
Turn the ignition on, then off, and then on again.
With the scan tool, read Amplifier DTCs.
Does the scan tool display active: B210E-BATTERY VOLTAGE HIGH?
Yes
>> Go To 2
No
>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-
matic as a guide, inspect the wiring and connectors.
Perform BODY VERIFICATION TEST VER-1.
2.
CHECK THE BATTERY VOLTAGE TO THE AMPLIFIER
With the scan tool in Data Display, read Amplifier battery voltage.
Is the battery voltage greater than 16.5 volts?
Yes
>> Go To 3
No
>> Replace the Amplifier in accordance with the Service Information.
Perform OCS VERIFICATION TEST - VER 1.
3.
CHECK FOR CHARGING SYSTEM RELATED DTCs IN THE POWERTRAIN CONTROL MODULE (PCM)
With the scan tool in ECU View, select PCM and check for any Charging System related DTCs.
Does the scan tool display any Charging System related DTCs?
Yes
>> Diagnose and repair the DTCs. Refer to (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).
No
>> Replace the Amplifier in accordance with the Service Information.
Perform OCS VERIFICATION TEST - VER 1.
LX
AUDIO - ELECTRICAL DIAGNOSTICS
8A - 5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст