Chrysler New Yorker. Manual — part 366

TEST 6A

REPAIRING DRIVER SQUIB CIRCUIT SHORTED TO GROUND

Perform TEST 1A Before Proceeding

FIG. 1

A

I

R
B
A

G

S
Y
S

T

E

M

62

TEST 6A

REPAIRING DRIVER SQUIB CIRCUIT SHORTED TO GROUND

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-1A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION

WARNING: DISCONNECT

DISCONNECT THE

OF ALL COMPONENTS.

THE BATTERY AND WAIT

DRIVER AIRBAG

START TEST 6A.

2 MINUTES BEFORE

MODULE SQUIB

PROCEEDING.

HARNESS

SEE GENERAL INFO 4.0

CONNECTOR.**

TURN IGNITION ON

DOES THE DRB

(ENGINE OFF).

WITH THE DRB, READ

DISPLAY

NO

REPLACE THE DRIVER

THE ACTIVE CODES.

"DRIVER SQUIB

AIRBAG MODULE.*

RECONNECT THE

CIRCUIT SHORTED TO

BATTERY. GROUND"?

YES

DISCONNECT THE

DOES THE DRB

CLOCKSPRING 2-WAY

WITH THE DRB, READ

DISPLAY

NO

REPLACE THE

HARNESS

THE ACTIVE CODES.

"DRIVER SQUIB

CLOCKSPRING.*

CONNECTOR.** CIRCUIT SHORTED TO

GROUND"?

YES

WARNING:

DISCONNECT THE

DISCONNECT THE

AIRBAG CONTROL

RECONNECT THE

BATTERY AND WAIT 2

MODULE 23-WAY

BATTERY.

MINUTES BEFORE

HARNESS

PROCEEDING.

CONNECTOR.**

USING A OHMMETER,

BETWEEN THE

REPAIR THE DRIVER

MEASURE THE DRIVER

CLOCKSPRING 2-WAY

IS THE RESISTANCE

YES

AIRBAG LINE 1

AIRBAG

HARNESS CONNECTOR

BELOW 5.0 OHMS ON

CIRCUIT OR LINE 2

LINE 1 CKT AND

AND GROUND.

EITHER CIRCUIT?

CIRCUIT FOR A

THEN LINE 2 CKT...

FIG. 1

SHORT TO GROUND.*

NO

PERFORM TEST

19A.

A

I

R
B
A

G

S
Y
S

T

E

M

63

TEST 7A

REPAIRING LOSS OF IGNITION RUN ONLY

Perform TEST 1A Before Proceeding

FIG. 1

FIG. 2

FIG. 3

A

I

R
B
A

G

S
Y
S

T

E

M

64

TEST 7A

REPAIRING LOSS OF IGNITION RUN ONLY

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-1A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION
OF ALL COMPONENTS.

TURN IGNITION ON

START TEST 7A.

(ENGINE OFF).

SEE GENERAL INFO 4.0

REMOVE AND INSPECT

FUSE #8.

YES

CONTINUE TEST

IS THE FUSE OPEN?

7A ON THE NEXT

PAGE.

FIG. 1

NO

USING A VOLTMETER,

REPAIR OPEN

MEASURE THE

IS THE VOLTAGE

NO

IGNITION SWITCH

IGNITION SWITCH

ABOVE 10.0 VOLTS?

OUTPUT CIRCUIT. IF

OUTPUT CIRCUIT

OK, REPLACE THE

(RUN ONLY). FIG. 1

IGNITION SWITCH.*

YES

WARNING:

DISCONNECT THE

REINSTALL

DISCONNECT THE

AIRBAG CONTROL

FUSE #8.

BATTERY AND WAIT 2

MODULE 23-WAY

MINUTES BEFORE

HARNESS CONNECTOR.**

PROCEEDING.

FIG. 2

TURN IGNITION ON.
EXIT THE VEHICLE.

RECONNECT THE

BATTERY.

USING A VOLTMETER,
MEASURE THE FUSED

IS THE VOLTAGE

YES

PERFORM TEST

IGNITION SWITCH

ABOVE 10.0 VOLTS?

19A.

OUTPUT RUN ONLY
CIRCUIT. FIG. 3

NO

REPAIR THE OPEN

FUSED IGNITION

SWITCH OUTPUT RUN

ONLY CIRCUIT.*

A

I

R
B
A

G

S
Y
S

T

E

M

65