Chrysler New Yorker. Manual — part 365

TEST 4A

REPAIRING DRIVER SQUIB CIRCUIT SHORTED

Perform TEST 1A Before Proceeding

FIG. 1

A

I

R
B
A

G

S
Y
S

T

E

M

58

TEST 4A

REPAIRING DRIVER SQUIB CIRCUIT SHORTED

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-1A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION

WARNING: DISCONNECT

OF ALL COMPONENTS.

THE BATTERY AND WAIT

START TEST 4A.

2 MINUTES BEFORE

PROCEEDING.

SEE GENERAL INFO 4.0

ENSURE THE DRIVER

IS COMPLETELY

AIRBAG MODULE

CONNECTED BEFORE

WAS THE CONNECTOR

NO

CONNECT AIRBAG

SQUIB HARNESS

DISCONNECTING IN COMPLETELY

MODULE.*

CONNECTOR... NEXT

STEP.

CONNECTED?

YES

DISCONNECT THE
DRIVER AIRBAG

MODULE SQUIB

HARNESS

CONNECTOR.**

TURN IGNITION ON.

DOES THE DRB

(ENGINE OFF).

WITH THE DRB, READ

DISPLAY

YES

REPLACE DRIVER

THE ACTIVE CODES.

"DRIVER SQUIB

AIRBAG MODULE.*

RECONNECT THE

CIRCUIT OPEN"?

BATTERY.

NO

DISCONNECT THE

DOES THE DRB

CLOCKSPRING 2-WAY

WITH THE DRB, READ

DISPLAY

YES

REPLACE THE

HARNESS

THE ACTIVE CODES.

"DRIVER SQUIB

CLOCKSPRING.*

CONNECTOR.** CIRCUIT OPEN"?

NO

TURN IGNITION OFF.

MEASURE BETWEEN THE

CHECK THE DRIVER

DRIVER AIRBAG LINE 1

IS THE RESISTANCE

YES

AIRBAG LINE 1

WITH AN

AND LINE 2 CKTS AT

BELOW 5.0 OHMS?

CIRCUIT FOR A

OHMMETER...

THE CLOCKSPRING

SHORT TO LINE 2

HARNESS CONN. FIG. 1

CIRCUIT.

NO

INSPECT THE

SHORTING CLIP FOR

DAMAGE. IF NO

SHORT IS FOUND,

REPLACE THE ACM.*

PERFORM TEST

19A.

A

I

R
B
A

G

S
Y
S

T

E

M

59

TEST 5A

REPAIRING DRIVER SQUIB CIRCUIT SHORTED TO BATTERY

Perform TEST 1A Before Proceeding

FIG. 1

A

I

R
B
A

G

S
Y
S

T

E

M

60

TEST 5A

REPAIRING DRIVER SQUIB CIRCUIT SHORTED TO BATTERY

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-1A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION

WARNING: DISCONNECT

DISCONNECT THE

OF ALL COMPONENTS.

THE BATTERY AND WAIT

DRIVER AIRBAG

START TEST 5A.

2 MINUTES BEFORE

MODULE SQUIB

PROCEEDING.

HARNESS

SEE GENERAL INFO 4.0

CONNECTOR.**

TURN IGNITION ON

DOES THE DRB

(ENGINE OFF).

WITH THE DRB, READ

DISPLAY

NO

REPLACE THE DRIVER

THE ACTIVE CODES.

"DRIVER SQUIB

AIRBAG MODULE.*

RECONNECT THE

CIRCUIT SHORTED TO

BATTERY. BATTERY"?

YES

DISCONNECT THE

DOES THE DRB

CLOCKSPRING 2-WAY

WITH THE DRB, READ

DISPLAY

NO

REPLACE THE

HARNESS

THE ACTIVE CODES.

"DRIVER SQUIB

CLOCKSPRING.*

CONNECTOR.** CIRCUIT SHORTED TO

BATTERY"?

YES

WARNING: DISCONNECT

DISCONNECT THE

TURN THE IGNITION

THE BATTERY AND WAIT

AIRBAG CONTROL

ON.

2 MINUTES BEFORE

MODULE 23-WAY

PROCEEDING.

HARNESS

RECONNECT THE

CONNECTOR.** BATTERY.

USING A VOLTMETER, BETWEEN THE

REPAIR

DRIVER

MEASURE THE DRIVER

CLOCKSPRING 2-WAY

IS THE VOLTAGE

YES

AIRBAG LINE 1

AIRBAG

HARNESS CONNECTOR

ABOVE 0.5 VOLTS ON

CIRCUIT OR LINE 2

LINE 1 CKT AND

AND GROUND.

EITHER CIRCUIT?

CIRCUIT FOR A

THEN LINE 2 CKT...

FIG. 1

SHORT TO VOLTAGE.*

NO

PERFORM TEST

19A.

A

I

R
B
A

G

S
Y
S

T

E

M

61