Chrysler New Yorker. Manual — part 90
(3) Insert fog lamp rearward into opening in front
bumper fascia.
(4) Install screw(s) attaching fog lamp to fascia.
(5) Verify fog lamp operation and alignment. Refer
to Fog Lamp Alignment procedures in this group.
FRONT PARKING, AND TURN SIGNAL LAMP
HOUSING – LHS
The front parking, and turn signal lamp housing is
part of the headlamp housing. For removal procedure
refer to Headlamp Housing Removal and Installation
procedures.
FRONT PARKING, SIDE MARKER, AND TURN
SIGNAL LAMP HOUSING – CONCORDE/300M
REMOVAL
(1) Remove headlamp housing to access lamp
housing.
(2) Rotate and pull socket from lamp housing.
(3) Disconnect fastener attaching lamp housing to
fascia (Fig. 7).
(4) Remove lamp housing from vehicle.
INSTALLATION
(1) Place lamp housing in position on fascia.
(2) Install lamp fastener.
(3) Install bulb socket in lamp.
(4) Verify lamp operation.
(5) Install headlamp housing.
FRONT PARKING, SIDE MARKER, AND TURN
SIGNAL LAMP HOUSING – INTREPID
The front parking, side marker, and turn signal
lamp housing is part of the headlamp housing. For
removal
procedure
refer
to
Headlamp
Housing
Removal and Installation procedures.
FRONT SIDE MARKER HOUSING – LHS
REMOVAL
(1) Loosen fascia as necessary to access lamp.
(2) Remove bulb socket from lamp.
(3) Disconnect fasteners attaching side marker
lamp to fascia (Fig. 8).
(4) Remove attaching fasteners.
(5) Remove lamp housing from vehicle.
INSTALLATION
(1) Place lamp in position on fascia.
(2) Install lamp fasteners.
(3) Install bulb socket in lamp.
(4) Connect wire harness connector.
(5) Verify lamp operation.
(6) Attach fascia to vehicle.
Fig. 5 Fog Lamp – LHS
Fig. 6 Fog Lamp – 300M
Fig. 7 Front Parking, Side Marker, and Turn Signal
Lamp Housing
8L - 18
LAMPS
300M
REMOVAL AND INSTALLATION (Continued)
HEADLAMP HOUSING – CONCORDE/LHS/330M
REMOVAL
(1) Release hood latch and open hood.
(2) Remove large rubber grommet (70 mm x 168
mm) from splash shield to gain access to fascia fas-
teners (Fig. 9).
(3) Remove fasteners attaching fascia to the front
fender and splash shield, using access hole in splash
shield (Fig. 10).
(4) Remove the push pins attaching the fascia to
the upper radiator closure panel (Fig. 11).
(5) Remove jackscrews attaching headlamp hous-
ing to crossmember and remove the lamp housing to
access the lamp(s) (Fig. 12).
(6) Roll fascia forward to clear way for headlamp
housing removal (Fig. 13).
(7) Disconnect wire connector from back of lamp
socket(s).
(8) Remove headlamp housing (Fig. 14).
INSTALLATION
CAUTION:
Do not touch the glass of halogen
bulbs with fingers or other possibly oily surface,
reduced bulb life will result.
(1) Place headlamp housing into position.
(2) Connect wire connector to lamp socket(s).
(3) Verify headlamp operation.
(4) Install jackscrews to attach headlamp housing
to crossmember.
(5) Align fascia to bumper reinforcement and
install the top center push pins, to upper radiator
closure panel.
(6) Align the two fascia studs to the fender vertical
attachments, at the same time align the fascia groove
on the horizontal flange with the fender drive pin.
Push fascia rearward to engage the fasteners.
(7) Install nut on fascia stud through the splash
shield access hole.
(8) Verify headlamp operation and alignment.
Fig. 8 Front Side Marker Lamp Housing
Fig. 9 Access Rubber Grommet
Fig. 10 Fastener Locations
Fig. 11 Remove Push In Fasteners
300M
LAMPS
8L - 19
REMOVAL AND INSTALLATION (Continued)
HEADLAMP HOUSING – INTREPID
Headlamp lens fogging is a normal condition
and does not require service. Moisture will vent
from tubes or vents located on the back of the
lamp.
REMOVAL
(1) Release hood latch and open hood.
(2) Remove jackscrews attaching headlamp to body
(Fig. 15).
(3) Remove headlamp from body.
(4) Disconnect wire connector from headlamp and
parking, side marker, and turn signal lamps.
(5) Remove headlamp housing from vehicle.
INSTALLATION
(1) Place headlamp housing in position on vehicle.
(2) Connect wire connector to headlamp, parking,
side marker, and turn signal lamps.
(3) Place headlamp lamp in position on body.
(4) Install screws to attach headlamp to body.
(5) Verify headlamp operation and alignment.
LICENSE PLATE LAMP – REAR BUMPER FASCIA
REMOVAL
(1) Remove screws holding license plate lamp to
fascia (Fig. 16).
(2) Remove license plate lamp from vehicle.
INSTALLATION
(1) Place license plate lamp in position on vehicle.
(2) Install screws to attach license plate lamp to
fascia.
Fig. 12 Headlamp Jackscrews
Fig. 13 Roll Fascia Forward
Fig. 14 Remove Headlamp Housing
Fig. 15 Headlamp Housing
8L - 20
LAMPS
300M
REMOVAL AND INSTALLATION (Continued)
TAIL, STOP, BACK UP, AND TURN SIGNAL LAMP
REMOVAL
(1) Release deck lid latch and open deck lid.
(2) Remove fasteners attaching trunk lining to
lower rear trunk panel.
(3) Move the trunk lining to access the tail lamp
fasteners.
(4) Remove nuts attaching tail lamp to lower
trunk and quarter panel (Fig. 17), and (Fig. 18).
(5) Remove tail lamp from vehicle.
(6) Disconnect tail lamp wire connector from body
wire harness.
INSTALLATION
(1) Connect tail lamp wire connector to body wire
harness.
(2) Place tail lamp in position on vehicle.
(3) Install nuts to attach tail lamp to lower trunk
and quarter panel.
(4) Place trunk lining in position on lower trunk
panel.
(5) Install fasteners to attach trunk lining to lower
rear trunk panel.
(6) Verify lamp operation.
Fig. 16 License Plate Lamp
Fig. 17 Tail, Stop, Back up, and Turn Signal –
Concorde/ LHS
Fig. 18 Tail, Stop, Back up, and Turn Signal –
Intrepid
Fig. 19 Tail, Stop, Back up, and Turn Signal – 300M
300M
LAMPS
8L - 21
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст