RAM 3500 (2019 year). Manual — part 28
IN CASE OF EMERGENCY
445
• Equipment malfunction at the SOS operator facility.
• Operator error by the SOS operator.
• LTE (voice/data) or 4G (data) network congestion.
• Weather.
• Buildings, structures, geographic terrain, or tunnels.
NOTE:
• Your vehicle may be transmitting data as authorized by
the subscriber.
• Never place anything on or near the vehicle’s LTE (voice/
data) or 4G (data) and GPS antennas. You could prevent
LTE (voice/data) or 4G (data) and GPS signal reception,
which can prevent your vehicle from placing an emer-
gency call. An operable LTE (voice/data) or 4G (data)
network connection and a GPS signal is required for the
SOS Call system to function properly.
General Information
This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
NOTE:
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
WARNING!
ALWAYS obey traffic laws and pay attention to the road.
ALWAYS drive safely with your hands on the steering
wheel. You have full responsibility and assume all risks
related to the use of the features and applications in this
vehicle. Only use the features and applications when it is
safe to do so. Failure to do so may result in an accident
involving serious injury or death.
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
446 IN CASE OF EMERGENCY
BULB REPLACEMENT
Replacement Bulbs
All of the inside bulbs are brass or glass-wedge base. Aluminum base bulbs are not approved.
Interior Bulbs
Bulb Number
Overhead Console Lamps
TS 212–9
Dome Lamp
7679
For lighted switches, see your authorized dealer for replacement instructions.
Exterior Bulbs (Sheet 1 of 2)
Bulb Number
Low Beam (Halogen Reflector Headlamp)
H11LL
High Beam (Halogen Reflector Headlamp)
9005LL
Low & High Beam (LED Reflector Headlamp)
LED (Serviced At An Authorized Dealer)
Low & High Beam (LED Projector Headlamp)
LED (Serviced At An Authorized Dealer)
Turn Signal / Front Position (Halogen Reflector Headlamp)
7444NA
Turn Signal / Front Position (LED Headlamps)
LED (Serviced at authorized dealer)
Front Side Marker (Halogen Reflector Headlamp)
W5W
Front Side Marker (LED Headlamps)
LED (Serviced At An Authorized Dealer)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
447
Replacing Exterior Bulbs
Base Quad: Low Beam Headlamp, High Beam Headlamp,
Front Park And Turn — If Equipped
Low Beam
1. Open the hood.
2. Disconnect and isolate the negative battery cable.
3. Reach into the front wheel house ahead of the front
wheel, remove the fastener, and lift the cover over the
access hole in the front of the wheel house splash shield.
Access to the rear of the lamp can be gained through this
access hole.
Front Fog Lamps (Halogen Reflector Headlamp)
H11LL
Front Fog Lamps (LED Headlamps)
LED (Serviced At An Authorized Dealer)
Side Indicators (Front And Side View Mirror)
LED (Serviced at authorized dealer)
Base Rear Tail/Turn and Stop Lamp
3157K
Premium Rear Tail/Turn and Stop Lamp
LED (Serviced At An Authorized Dealer)
Premium Backup Lamp
7440/W21W
Center High Mounted Stop Lamp (CHMSL)
921
Cab Roof Marker Lamps
194NA
Rear Lamp Bar ID Marker Lamp
194
Side Marker Lamps (Dual Rear Wheels)
194
Backup Lamp
921
Rear License Plate Lamp
194
Exterior Bulbs (Continued) (Sheet 2 of 2)
Bulb Number
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
448 IN CASE OF EMERGENCY
Splash Shield Access Cover
4. Reach through the access hole of the wheel house splash
shield and disengage the bulb access cover by rotating
counterclockwise.
Bulb Access Cover
5. Disconnect the internal lamp wiring harness connector
from the low beam bulb.
1 — Access Cover
2 — Fastener
CAUTION!
• Do not contaminate the bulb glass by touching it with
your fingers or by allowing it to contact other oily
surfaces. Shortened bulb life will result.
• Always use the correct bulb size and type for replace-
ment. An incorrect bulb size or type may overheat and
cause damage to the lamp, the bulb socket, or the lamp
wiring.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
449
(Continued)
6. Rotate the bulb counterclockwise 1/4 turn to unlock the
bulb from the lamp.
7. Pull the bulb straight out from the housing.
8. Reverse the procedure for installation of new bulb and
covers.
High Beam
1. Open the hood.
2. Disconnect and isolate the negative battery cable.
3. Look under the hood and behind the headlamp to find
the high beam bulb access cover.
4. Reach behind the headlamp and disengage the access
cover by rotating counterclockwise.
5. Disconnect the internal lamp wiring harness connector
from the high beam bulb.
6. Rotate the bulb counterclockwise 1/4 turn to unlock the
bulb from the lamp.
7. Pull the bulb straight out from the housing.
8. Reverse the procedure for installation of new bulb and
covers.
Front Park And Turn
1. Open the hood.
2. Disconnect and isolate the negative battery cable.
3. Look under the hood and behind the headlamp to find
the park and turn socket.
CAUTION!
• Do not contaminate the bulb glass by touching it with
your fingers or by allowing it to contact other oily
surfaces. Shortened bulb life will result.
• Always use the correct bulb size and type for replace-
ment. An incorrect bulb size or type may overheat and
cause damage to the lamp, the bulb socket, or the lamp
wiring.
CAUTION! (Continued)
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
450 IN CASE OF EMERGENCY
Park And Turn Socket
4. Reach behind the headlamp and unlock the park and
turn socket from the lamp by rotating counterclock-
wise ¼ turn.
5. Pull the bulb straight out from the housing.
6. Separate the bulb from the socket without twisting.
7. Reverse the procedure for installation of new bulb and
covers.
Side Marker Lamp
1. Open the hood.
2. Disconnect and isolate the negative battery cable.
3. Reach into the front wheel house ahead of the front
wheel, remove the fastener, and lift the cover over the
access hole in the front of the wheel house splash shield.
Access to the rear of the lamp can be gained through this
access hole.
Splash Shield Access Cover
1 — Access Cover
2 — Fastener
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
451
4. Reach through the access hole of the wheel house splash
shield and disengage the side marker socket by rotating
counterclockwise ¼ turn.
Side Marker Socket
5. Pull the socket and bulb straight out from the housing.
6. Separate the bulb from the socket without twisting.
7. Reverse the procedure for installation of new bulb and
covers.
Fog Lamps — If Equipped
1. Reach under and behind the front bumper to access the
back of the front fog lamp housing.
2. Disconnect the fog lamp wiring harness connector from
the fog lamp bulb.
3. Rotate the bulb counterclockwise ¼ turn to unlock the
bulb from the housing.
4. Pull the bulb straight out from the housing.
CAUTION!
Do not contaminate the bulb glass by touching it with
your fingers or by allowing it to contact other oily
surfaces. Shortened bulb life will result.
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
452 IN CASE OF EMERGENCY
Rear Tail/Stop, Turn Signal And Backup Lamps
1. Remove the two screws and push pins that pass through
the bed sheet metal.
Tail Lamp Locations
2. Pull the outboard side of the lamp rearward far enough to
unsnap the two receptacles on the outboard side of the
lamp housing from the two plastic snap post retainers in
the outer box side panel.
Tail Lamp Removed
3. Disconnect the wiring harness connectors from the bulb
socket.
1 — Tail Lamp
2 — Fasteners
1 — Tail Lamp Housing
2 — Bulb Socket Locations
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
453
4. Rotate the bulb socket counterclockwise 1/4 turn to
unlock it from the housing.
5. Pull the bulb straight out of the socket.
6. Reverse the procedure to install the bulb and housing.
Center High-Mounted Stoplamp (CHMSL) With Cargo
Lamp
1. Remove the two screws holding the housing/lens to the
body as shown.
CHMSL Mounting Screw Locations
CAUTION!
Do not contaminate the bulb glass by touching it with
your fingers or by allowing it to contact other oily
surfaces. Shortened bulb life will result.
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
454 IN CASE OF EMERGENCY
2. Separate the connector holding the housing and wiring
harness to the body.
CHMSL Connector Location
3. Turn the desired bulb socket ¼ turn and remove the
socket and bulb from housing.
4. Pull the desired bulb straight from the socket.
CHMSL Bulb And Socket
•Outside Bulbs: Cargo Lamps
•Inside Bulb: Center High-Mounted Stop Lamp
5. Reverse the procedure for installation of bulbs and
housing.
CAUTION!
Do not contaminate the bulb glass by touching it with
your fingers or by allowing it to contact other oily
surfaces. Shortened bulb life will result.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
455
Cab Top Clearance Lamps — If Equipped
1. Remove the two screws from the top of the lamp.
Removing Rear Screw From Clearance Lamp
2. Rotate the bulb socket ¼ turn and pull it from the lamp
assembly.
Removing Bulb Socket From Clearance Lamp
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
456 IN CASE OF EMERGENCY
3. Pull the bulb straight from it's socket and replace.
Removing The Bulb From The Bulb Socket
Rear Lamp Bar ID Marker (Dual Rear Wheels) — If
Equipped
1. Loosen the two screws and the housing to gain access to
the bulb sockets.
Screw Locations
2. Turn the socket ¼ turn counterclockwise to access the
bulb.
3. Pull the bulb straight out from the socket.
4. Reverse the procedure for installation of the bulbs and
housing.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
457
Side Marker Lamps (Dual Rear Wheels) — If Equipped
Side Marker Lamp Locations
1. Push rearward on the side marker lamp assembly.
2. Pull the entire assembly from the fender.
3. Turn the socket ¼ turn counterclockwise and remove
from assembly to access the bulb.
4. Pull the bulb straight out from socket.
5. Reverse the procedure for installation of the bulbs and
housing.
FUSES
WARNING!
• When replacing a blown fuse, always use an appro-
priate replacement fuse with the same amp rating as the
original fuse. Never replace a fuse with another fuse of
higher amp rating. Never replace a blown fuse with
metal wires or any other material. Do not place a fuse
inside a circuit breaker cavity or vice versa. Failure to
use proper fuses may result in serious personal injury,
fire and/or property damage.
• Before replacing a fuse, make sure that the ignition is
off and that all the other services are switched off and/
or disengaged.
• If the replaced fuse blows again, contact an authorized
dealer.
• If a general protection fuse for safety systems (air bag
system, braking system), power unit systems (engine
system, transmission system) or steering system blows,
contact an authorized dealer.
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
458 IN CASE OF EMERGENCY
Power Distribution Center
The Power Distribution Center is located in the engine
compartment near the battery. This center contains cartridge
fuses, micro fuses, relays, and circuit breakers. A description
of each fuse and component may be stamped on the inside
cover, otherwise the cavity number of each fuse is stamped
on the inside cover that corresponds to the following chart.
Power Distribution Center Location
Cavity
Cartridge Fuse
Micro Fuse
Description
F01
80 Amp Black
–
Rad Fan Control Module – If Equipped (DS 1500
Only)
F02
60 Amp Yellow
–
ABS Pump Motor (HD Only)
F03
60 Amp Yellow
–
Rad Fan – If Equipped
F04
50 Amp Red
400W Inverter – If Equipped (HD Only)
F05
40 Amp Green
50 Amp Red (Special
Services Vehicle (SSV))
–
Compressor For Air Suspension – If Equipped
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
459
F06
40 Amp Green
–
ABS Pump Motor (DS 1500 Only)
F07
40 Amp Green
–
Starter Solenoid
F08
20 Amp Blue (DS 1500
LD/Cummins Diesel)
40 Amp Green
–
–
NOX Sensor – If Equipped
Aux Relay Output- SSV Only
F09
40 Amp Green (SSV &
Cummins Diesel)
–
Aux Relay Output / Diesel Fuel Heater – If
Equipped
F09
30 Amp Pink
–
Brake Vacuum Pump – If Equipped (HD Only)
F10
40 Amp Green
–
Body Controller / Exterior Lighting #2
F11
30 Amp Pink
–
PWR - Trailer Tow Electric Brake Batt Feed – If
Equipped (DS 1500 Only)
F11
40 Amp Green
–
Brake System Module (ECU and Valves) (HD
Only)
F12
40 Amp Green
–
Body Controller #3
F13
40 Amp Green
–
Blower Motor
F14
40 Amp Green
–
Body Controller #4 / Exterior Lighting
F15
30 Amp Pink
40 Amp Green
–
–
Power Side Steps – If Equipped (HD Only)
Extra Fuse - SSV Only
F16
30 Amp Pink
–
Smart-Bar Module – If Equipped (HD Only)
F17
30 Amp Pink
–
Winch Control Module – If Equipped (HD Only)
Cavity
Cartridge Fuse
Micro Fuse
Description
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
460 IN CASE OF EMERGENCY
F19
20 Amp Blue (DS 1500
LD Diesel)
30 Amp Pink
(Cummins Diesel)
–
SCR – If Equipped
F20
30 Amp Pink
–
Passenger Door Module
F21
30 Amp Pink
–
Drive Train Control Module
F22
20 Amp Blue
–
Engine Control Module GPEC / Heavy Duty /
Other – If Equipped
F22
25 Amp White
(Cummins Diesel)
–
PCM – If Equipped
F23
30 Amp Pink
–
CBC Feed # 1
F24
30 Amp Pink
–
Driver Door Module
F25
30 Amp Pink
–
Front Wiper
F26
30 Amp Pink
–
Antilock Brakes / Stability Control Module /
Valves – If Equipped (DS 1500 Only)
F28
20 Amp Blue
–
Trailer Tow Backup Lights – If Equipped
F29
20 Amp Blue
–
Trailer Tow Parking Lights – If Equipped
F30
30 Amp Pink
–
Trailer Tow Receptacle / Trailer Tow (Separate
E-Brake)/Trailer Tow (BUX)
Cavity
Cartridge Fuse
Micro Fuse
Description
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст