Chrysler Stratus Convertible. Manual — part 261
PARK AND TURN SIGNAL LAMP BULB
REMOVAL
(1) Release hood latch and open hood.
(2) Remove screws attaching headlamp module to
radiator closure panel.
(3) Remove headlamp module from radiator clo-
sure panel.
(4) Rotate socket counterclockwise one quarter
turn.
(5) Pull socket from back of lamp (Fig. 3).
(6) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Position socket into back of lamp.
(3) Rotate socket clockwise one quarter turn.
(4) Position headlamp module to radiator closure
panel.
(5) Install screws attaching headlamp module to
radiator closure panel.
(6) Verify proper headlamp alignment.
CENTER HIGH MOUNTED STOP LAMP
(CHMSL) BULB
The center high mounted stop lamp (CHMSL) has
no serviceable bulb. If the lamp does not function
properly, the CHMSL assembly must be replaced.
TAIL, BRAKE AND TURN SIGNAL LAMP BULBS
REMOVAL
(1) Release decklid latch and open decklid.
(2) Remove trunk lining as necessary to gain
access to tail lamp nuts.
(3) Remove plastic nuts attaching tail lamp to rear
closure panel.
(4) Remove lamp from opening in quarter panel.
(5) Rotate socket counterclockwise one quarter
turn.
(6) Pull socket from back of lamp (Fig. 4).
(7) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Push socket into back of lamp.
(3) Rotate socket clockwise one quarter turn.
(4) Position lamp to opening in quarter panel.
(5) Install plastic nuts attaching tail lamp to rear
closure panel.
(6) Install trunk lining.
(7) Close decklid.
Fig. 2 Fog Lamp Bulb
1 – FASCIA FOGLAMP HOUSING
2 – FOGLAMP BULB
Fig. 3 Park and Turn Signal Lamp Bulb
1 – BULB
2 – HEADLAMP MODULE
Fig. 4 Tail, Brake, and Turn Signal Lamp Bulb
1 – REAR CLOSURE PANEL
2 – TAIL, STOP, TURN SIGNAL LAMP HOUSING
3 – BULBS
JX
LAMPS
8L - 9
REMOVAL AND INSTALLATION (Continued)
BACK-UP LAMP BULB
REMOVAL
(1) Release decklid latch and open decklid.
(2) Remove trunk lining as necessary to gain
access to tail lamp nuts.
(3) Remove plastic nuts attaching tail lamp to rear
closure panel.
(4) Remove lamp from opening in quarter panel.
(5) Rotate socket counterclockwise one quarter
turn.
(6) Pull socket from back of lamp.
(7) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Push socket into back of lamp.
(3) Rotate socket clockwise one quarter turn.
(4) Position tail lamp to opening in quarter panel.
(5) Install plastic nuts attaching tail lamp to rear
closure panel.
(6) Install trunk lining.
LICENSE PLATE LAMP BULB
REMOVAL
(1) Remove screws attaching license plate lamp to
rear bumper fascia.
(2) Remove license plate lamp from rear fascia.
(3) Rotate socket counterclockwise one quarter
turn.
(4) Pull socket from back of lamp (Fig. 5).
(5) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Push socket into back of lamp.
(3) Rotate socket clockwise one quarter turn.
(4) Position license plate lamp to rear fascia.
(5) Install screws attaching license plate lamp to
rear bumper fascia.
DOOR COURTESY LAMP BULB
REMOVAL
(1) Using a small, flat bladed tool inserted into
rear edge of door courtesy lamp lens, remove lens.
(2) Pull courtesy lamp bulb from bulb socket (Fig.
6).
INSTALLATION
(1) Push courtesy lamp bulb into bulb socket.
(2) Insert front edge of courtesy lamp lens to lamp
housing.
(3) Snap lamp lens into lamp housing.
FRONT MAP LAMP BULB
REMOVAL
(1) Using a small, flat bladed tool inserted into slot
in lamp lens, remove map lamp lens.
(2) Pull bulb from map lamp.
INSTALLATION
(1) Push bulb into map lamp.
(2) Install map lamp lens.
Fig. 5 License Plate Lamp Bulb
1 – BULB
2 – LICENSE PLATE LAMP
Fig. 6 Door Courtesy Lamp Bulb
1 – BULB
2 – COURTESY LAMP HOUSING
3 – DOOR TRIM PANEL
8L - 10
LAMPS
JX
REMOVAL AND INSTALLATION (Continued)
ASH RECEIVER/CUP HOLDER LAMP BULB
REMOVAL
(1) Use a small, flat bladed pry tool, insert into the
slot in lamp bezel, and push inward to release from
cubby bin.
(2) Pull lamp assembly from cubby bin.
(3) Remove lamp cover.
(4) Remove bulb.
INSTALLATION
(1) Install bulb.
(2) Install lamp cover.
(3) Position lamp assembly into cubby bin connec-
tor end first, and snap lamp into cubby bin.
FLOOR CONSOLE COURTESY LAMP BULB
REMOVAL
(1) Using a small, flat bladed tool inserted into top
edge of courtesy lamp, remove courtesy lamp from
floor console (Fig. 7).
(2) Rotate bulb socket counterclockwise one quar-
ter turn.
(3) Pull bulb socket from courtesy lamp.
(4) Pull bulb from bulb socket (Fig. 8).
INSTALLATION
(1) Push bulb into bulb socket.
(2) Push bulb socket into courtesy lamp.
(3) Rotate bulb socket clockwise one quarter turn.
(4) Position lower edge of courtesy lamp to floor
console.
(5) Snap courtesy lamp into floor console.
LIGHTED TRANSMISSION RANGE INDICATOR
LETTER BEZEL LAMP
The Lighted Transmission Range Indicator Letter
Bezel Lamp, is not a serviceable lamp. If the lamp
does not function properly, the Lighted Transmission
Range Indicator Letter Bezel assembly must be
replaced.
Fig. 7 Floor Console Courtesy Lamp
1 – FLOOR CONSOLE
2 – FLOOR CONSOLE COURTESY LAMP
Fig. 8 Floor Console Courtesy Lamp Bulb
1 – FLOOR CONSOLE
2 – BULB
3 – FLOOR CONSOLE COURTESY LAMP
JX
LAMPS
8L - 11
REMOVAL AND INSTALLATION (Continued)
LAMP HOUSING
TABLE OF CONTENTS
page
page
REMOVAL AND INSTALLATION
HEADLAMP MODULE . . . . . . . . . . . . . . . . . . . . . 12
FOG LAMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CENTER HIGH MOUNTED STOP LAMP
(CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TAIL, BRAKE, TURN SIGNAL, BACKUP AND
SIDE MARKER LAMPS . . . . . . . . . . . . . . . . . . . 13
LICENSE PLATE LAMP . . . . . . . . . . . . . . . . . . . . 14
DOOR COURTESY LAMP . . . . . . . . . . . . . . . . . . 14
FRONT MAP LAMP . . . . . . . . . . . . . . . . . . . . . . . 15
ASH RECEIVER/CUP HOLDER LAMP . . . . . . . . . 15
FLOOR CONSOLE COURTESY LAMP . . . . . . . . . 15
LIGHTED TRANSMISSION RANGE INDICATOR
LETTER BEZEL . . . . . . . . . . . . . . . . . . . . . . . . 16
SPECIAL TOOLS
LAMP SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . 16
REMOVAL AND INSTALLATION
HEADLAMP MODULE
The headlamp module contains the park and turn
signal lamps and is serviced as an assembly.
REMOVAL
(1) Release hood latch and open hood.
(2) Remove screws attaching headlamp module to
radiator closure panel and headlamp adapter (Fig. 1).
(3) Remove headlamp module from radiator clo-
sure panel (Fig. 2).
(4) Disconnect wire connector from headlamp bulb
socket.
(5) Rotate park/turn signal lamp socket one quar-
ter turn counterclockwise.
(6) Pull park/turn signal socket from headlamp
module.
(7) Remove headlamp module from vehicle.
INSTALLATION
(1) Position headlamp module to vehicle.
(2) Push park/turn signal socket into headlamp
module.
(3) Rotate park/turn signal lamp socket one quar-
ter turn clockwise.
(4) Connect wire connector to headlamp bulb
socket.
(5) Position headlamp module to radiator closure
panel.
(6) Install screws attaching headlamp module to
radiator closure panel.
(7) Verify proper headlamp alignment.
FOG LAMP
REMOVAL
(1) Raise vehicle with suitable lifting device. Refer
to Group 0, Lubrication and Maintenance, for proper
procedures.
(2) Disconnect wire connector from fog lamp bulb.
(3) Remove nuts attaching fog lamp to front fascia.
(4) Remove fog lamp from front fascia.
Fig. 1 Headlamp Module Screws
1 – MODULE SCREWS
2 – HEADLAMP MODULE
8L - 12
LAMPS
JX
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст