Chrysler Stratus Convertible. Manual — part 262
INSTALLATION
(1) Position fog lamp in front fascia.
(2) Install nuts attaching fog lamp to front fascia.
(3) Connect wire connector to fog lamp bulb.
CENTER HIGH MOUNTED STOP LAMP
(CHMSL)
REMOVAL
(1) Remove upper deck molding. Refer to Group
23, Body, for proper procedure.
(2) Remove screws attaching CHMSL assembly to
upper deck molding (Fig. 4).
(3) Remove trunk trim panel as necessary to con-
nect CHMSL wire connector.
(4) Remove CHMSL from upper deck molding.
INSTALLATION
(1) Position CHMSL to upper deck molding.
(2) Connect CHMSL wire connector and reposition
trunk trim panel.
(3) Install screws attaching CHMSL assembly to
upper deck molding.
(4) Install upper deck molding. Refer to Group 23,
Body, for proper procedure.
TAIL, BRAKE, TURN SIGNAL, BACKUP AND
SIDE MARKER LAMPS
REMOVAL
(1) Release decklid latch and open decklid.
(2) Remove trunk lining as necessary to gain
access to tail lamp nuts.
(3) Remove plastic nuts attaching tail lamp to rear
closure panel.
(4) Remove lamp from opening in quarter panel
(Fig. 5).
(5) Rotate bulb sockets counterclockwise one quar-
ter turn.
(6) Pull bulb sockets from back of lamp.
(7) Remove tail, brake, turn signal, backup and
side marker lamps from vehicle.
Fig. 2 Headlamp Module
1 – HEADLAMP MODULE
2 – FRONT BUMPER FASCIA
3 – RADIATOR CLOSURE PANEL
Fig. 3 Fog Lamp
1 – FOGLAMP
2 – FASCIA FOGLAMP HOUSING
Fig. 4 Center High Mount Stop Lamp
1 – WIRE HARNESS
2 – CHMSL
3 – UPPER DECK MOLDING
4 – WIRE CONNECTOR
JX
LAMPS
8L - 13
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Position tail, brake, turn signal, backup and
side marker lamp to vehicle.
(2) Push bulb sockets into back of lamp.
(3) Rotate bulb sockets clockwise one quarter turn.
(4) Position lamp to opening in quarter panel.
(5) Install plastic nuts to attach tail lamp to rear
closure panel in the following sequence: outboard,
center, inboard.
(6) Install trunk lining.
LICENSE PLATE LAMP
REMOVAL
(1) Remove screws attaching license plate lamp to
rear bumper fascia.
(2) Remove license plate lamp from rear fascia
(Fig. 6).
(3) Rotate socket counterclockwise one quarter
turn.
(4) Pull socket from back of lamp.
(5) Remove license plate lamp from vehicle.
INSTALLATION
(1) Position license plate lamp to vehicle.
(2) Push socket into back of lamp.
(3) Rotate socket clockwise one quarter turn.
(4) Position license plate lamp to rear fascia.
(5) Install screws attaching license plate lamp to
rear bumper fascia.
DOOR COURTESY LAMP
REMOVAL
(1) Using a small, flat bladed tool inserted into
rear edge of door courtesy lamp lens, remove lens
(Fig. 7).
(2) Pull courtesy lamp from door trim panel (Fig.
8).
(3) Disengage wire connector from courtesy lamp
bulb socket.
Fig. 5 Tail, Brake, Turn Signal, Backup and Side Marker Lamp
1 – TAIL, STOP, TURN SIGNAL, BACKUP AND SIDEMARKER
LAMP
2 – WIRE HARNESS
Fig. 6 License Plate Lamp
1 – REAR BUMPER FASCIA
2 – LICENSE PLATE LAMP
8L - 14
LAMPS
JX
REMOVAL AND INSTALLATION (Continued)
(4) Remove courtesy lamp from vehicle.
INSTALLATION
(1) Position courtesy lamp from vehicle.
(2) Connect wire connector to courtesy lamp bulb
socket.
(3) Push courtesy lamp into door trim panel (Fig.
8).
(4) Insert front edge of courtesy lamp lens to lamp
housing.
(5) Snap lamp lens into lamp housing.
FRONT MAP LAMP
The front map lamp is not a serviceable compo-
nent. If the front map lamp does not operate prop-
erly, the rear view mirror assembly must be replaced.
ASH RECEIVER/CUP HOLDER LAMP
REMOVAL
(1) Using a small, flat bladed pry tool inserted into
slot in lamp bezel, release tab holding lamp to cubby
bin.
(2) Pull bezel and lamp assembly from cubby bin.
(3) Disconnect wire connector from lamp assembly.
(4) Remove lamp assembly from vehicle.
INSTALLATION
(1) Position lamp assembly to vehicle.
(2) Connect wire connector to lamp assembly.
(3) Push bezel and lamp assembly into cubby bin
to engage tabs.
FLOOR CONSOLE COURTESY LAMP
REMOVAL
(1) Using a small, flat bladed tool inserted into slot
in top edge of courtesy lamp, remove courtesy lamp
from floor console (Fig. 9).
(2) Rotate bulb socket counterclockwise one quar-
ter turn.
(3) Pull bulb socket from courtesy lamp (Fig. 10).
(4) Remove console courtesy lamp from vehicle.
INSTALLATION
(1) Place console courtesy lamp in position.
(2) Push bulb socket into courtesy lamp.
(3) Rotate bulb socket clockwise one quarter turn.
(4) Position lower edge of courtesy lamp to floor
console.
(5) Snap courtesy lamp into floor console.
Fig. 7 Courtesy Lamp Lens
1 – COURTESY LAMP HOUSING
2 – DOOR TRIM PANEL
3 – COURTESY LAMP LENS
Fig. 8 Courtesy Lamp
1 – COURTESY LAMP HOUSING
2 – DOOR TRIM PANEL
Fig. 9 Floor Console Courtesy Lamp
1 – FLOOR CONSOLE
2 – FLOOR CONSOLE COURTESY LAMP
JX
LAMPS
8L - 15
REMOVAL AND INSTALLATION (Continued)
LIGHTED TRANSMISSION RANGE INDICATOR
LETTER BEZEL
REMOVAL
(1) Remove floor console. Refer to Group 23, Body,
for proper procedure.
(2) Disconnect the wire harness connector on bot-
tom-side of floor console.
(3) Disconnect the inverter for lighted Transmis-
sion Range Indicator letter bezel from shifter cover.
(4) Pull bezel downward through access hole in
floor console.
(5) Remove lighted transmission range indicator
letter bezel from vehicle.
INSTALLATION
(1) Position lighted transmission range indicator
letter bezel to vehicle.
(2) Push bezel upward through access hole in floor
console.
(3) Connect inverter for lighted transmission range
indicator letter bezel to shifter cover.
(4) Connect the wire harness connector on bottom-
side of floor console.
(5) Install floor console. Refer to Group 23, Body,
for proper procedure.
SPECIAL TOOLS
LAMP SERVICE
Fig. 10 Floor Console Courtesy Lamp Bulb
1 – FLOOR CONSOLE
2 – BULB
3 – FLOOR CONSOLE COURTESY LAMP
Trim Stick C-4755
8L - 16
LAMPS
JX
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст