Chrysler 300M, Dodge Interpid. Manual — part 353
HOOD
REMOVAL
(1) Raise hood to full up position.
(2) Mark all bolt and hinge attachment locations
with a grease pencil or other suitable device to pro-
vide reference marks for installation.
(3) Remove the top bolts attaching hood to hinge
and loosen the bottom bolts until they can be
removed by hand (Fig. 2).
(4) With assistance from a helper at the opposite
side of the vehicle to support the hood, remove bot-
tom bolts attaching hood to hinge. Remove the hood
from the vehicle.
INSTALLATION
(1) Place hood in position on vehicle. With assis-
tance from a helper at the opposite side of the vehicle
to support the hood, install bottom bolts attaching
hood to hinge finger tight.
(2) Install top bolts to attach hood to hinge finger
tight. When installing hood, align all marks and
secure bolts. The hood should be aligned to 4 mm
(0.160 in.) gap to the front fenders and flush across
the top surfaces along fenders.
(3) Position bolts at marks and tighten bolts to 22.6
to 33.9 N·m (200 to 300 in. lbs.) torque. The hood should
be aligned to 4 mm (0.160 in.) gap to the front fenders
and flush across the top surfaces along fenders.
(4) Verify hood operation and alignment.
LATCH
REMOVAL
(1) Release hood latch and open hood.
(2) Remove nuts attaching hood latch to cross-
member (Fig. 3)or (Fig. 4).
(3) Remove hood latch from crossmember.
(4) Disconnect hood release cable from hood latch.
Fig. 2 HOOD
1 - HOOD
2 - HOOD HINGE
3 - GAS PROP
4 - BOLTS
Fig. 3 HOOD LATCH - CONCORDE/300M
1 - HOOD BUMPER ADJUSTER
2 - HOOD RELEASE CABLE CLIPS
3 - NUTS
4 - HOOD LATCH
LH
HOOD
23 - 41
INSTALLATION
(1) Connect hood release cable to hood latch.
(2) Place hood latch in position on crossmember.
(3) Install nuts attaching hood latch to crossmem-
ber. Tighten nuts to 22.6 to 33.9 N·m (200 to 300 in.
lbs.) torque.
(4) Verify hood latch operation before closing hood.
LATCH RELEASE CABLE
REMOVAL
(1) Release hood latch by using the inside release,
if still functioning. If not reach up through the bot-
tom of the fascia opening and release the latch pawl
lever.
(2) Disconnect hood release cable ferrule and cable
end from hood latch assembly (Fig. 5) or (Fig. 6).
(3) Remove left cowl side trim panel.
(4) Remove screws attaching hood latch release
cable handle to the cowl side.
(5) Remove left wheel splash shield.
(6) Disengage release cable from routing clips.
(7) Roll carpet back to expose cable.
(8) Release taped on cable clip from dash liner
(Fig. 7).
(9) Release the rubber grommet from the dash
panel. Pull cable through the dash panel access hole.
(10) Remove cable from vehicle.
Fig. 4 HOOD LATCH - INTREPID
1 - HOOD BUMPER ADJUSTER
2 - HOOD LATCH
3 - RELEASE CABLE CLIP
4 - NUTS
Fig. 5 HOOD RELEASE CABLE - CONCORDE/300M
1 - HOOD LATCH
2 - HOOD RELEASE CABLE
Fig. 6 HOOD RELEASE CABLE - INTREPID
1 - HOOD LATCH
2 - HOOD RELEASE CABLE
23 - 42
HOOD
LH
LATCH (Continued)
INSTALLATION
(1) Place cable in position on vehicle.
(2) Push cable through access hole in dash panel.
(3) Install release cable rubber grommet into
access hole in dash panel.
(4) Install screws attaching hood latch release
cable handle to the cowl side. Tighten screws to 2.3
to 3.4 N·m (20 to 30 in. lbs.) torque.
(5) Install cable clips.
(6) Place carpet into position.
(7) Install left wheel splash shield.
(8) Install left cowl side trim panel.
(9) Connect hood release cable ferrule and cable
end to hood latch.
(10) Verify hood latch operation before closing
hood.
SUPPORT CYLINDER
REMOVAL
(1) Open hood.
(2) Support hood with a suitable prop device.
(3) Remove gas prop lock caps on each end (Fig. 8).
(4) Remove gas prop from vehicle.
INSTALLATION
(1) Place gas prop in position on vehicle.
(2) Install the lock caps on the gas prop.
(3) Verify hood lid operation.
Fig. 7 HOOD RELEASE HANDLE
1 - RUBBER GROMMET
2 - SCREWS
3 - HOOD RELEASE HANDLE
4 - HOOD RELEASE CABLE
Fig. 8 HOOD GAS PROP
1 - LOCK CAP
2 - GAS PROP
3 - LOCK CAP
LH
HOOD
23 - 43
LATCH RELEASE CABLE (Continued)
INSTRUMENT PANEL
TABLE OF CONTENTS
page
page
CLUSTER BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
. . . . . . . . . . . . . . . . . . . . . . . . . 44
DASH SILENCER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
. . . . . . . . . . . . . . . . . . . . . . . . . 45
GLOVE BOX
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
. . . . . . . . . . . . . . . . . . . . . . . . . 46
GLOVE BOX LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
. . . . . . . . . . . . . . . . . . . . . . . . . 46
INSTRUMENT PANEL ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
. . . . . . . . . . . . . . . . . . . . . . . . . 55
INSTRUMENT PANEL CENTER BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
. . . . . . . . . . . . . . . . . . . . . . . . . 56
INSTRUMENT PANEL END CAP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
. . . . . . . . . . . . . . . . . . . . . . . . . 56
INSTRUMENT PANEL SILENCER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
. . . . . . . . . . . . . . . . . . . . . . . . . 56
INSTRUMENT PANEL TOP COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
. . . . . . . . . . . . . . . . . . . . . . . . . 57
UPPER RIGHT TRIM BEZEL(300M)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
. . . . . . . . . . . . . . . . . . . . . . . . . 57
STORAGE BIN - 5 PASSENGER VEHICLES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
. . . . . . . . . . . . . . . . . . . . . . . . . 58
STORAGE BIN - 6 PASSENGER VEHICLES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
. . . . . . . . . . . . . . . . . . . . . . . . . 58
STEERING COLUMN COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
. . . . . . . . . . . . . . . . . . . . . . . . . 58
STEERING COLUMN COVER REINFORCEMENT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
. . . . . . . . . . . . . . . . . . . . . . . . . 59
CLUSTER BEZEL
REMOVAL
(1) Open hood and disconnect the negative battery
cable remote terminal from the remote battery post
(Fig. 1).
(2) Remove the instrument panel left end cap.
(3) Remove steering column shroud cover.
(4) Tilt the steering column down into the lowest
position.
(5) Remove one screw (Concorde/300M) to cluster
bezel
(6) Remove the items to expose bezel mounting
screws. Items vary depending on model.
(7) Remove two screws over upper cluster bezel in
instrument panel brow area and all remaining
attaching screws.
(8) Using a trim stick (special tool #C-4755), gently
pry out on the instrument panel cluster bezel, discon-
nect headlamp switch connector, and remove.
INSTALLATION
(1) Connect headlamp switch connector. Place the
cluster bezel into position and snap it into place
firmly.
(2) Install the two screws over upper cluster bezel
in instrument panel brow area and all remaining
attaching screws.
Fig. 1 NEGATIVE BATTERY CABLE REMOTE
TERMINAL
1 - RIGHT STRUT TOWER
2 - AIR CLEANER INLET TUBE
3 - REMOTE TERMINAL
23 - 44
INSTRUMENT PANEL
LH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст