Chrysler 300M, Dodge Interpid. Manual — part 362
PAINT CODE
DESCRIPTION
Exterior vehicle body colors are identified on the
Body Code plate. (Refer to VEHICLE DATA/VEHI-
CLE
INFORMATION/BODY
CODE
PLATE
-
DESCRIPTION). The paint code is also identified on
the Vehicle Safety Certification Label which is
located on the drivers door shut face. The first digit
of the paint code listed on the vehicle indicates the
sequence of application, i.e.: P = primary coat, Q =
secondary coat. The codes listed in the Color Code
Chart are used for manufacturing purposes.
PAINT SURFACE TOUCH-UP
DESCRIPTION
When a painted metal surface has been scratched
or chipped, it should be touched up as soon as possi-
ble to avoid corrosion. For best results, use Mopar
t
Scratch Filler/Primer, Touch Up Paints and Clear Top
Coat. (Refer to VEHICLE DATA/VEHICLE INFOR-
MATION/BODY CODE PLATE - DESCRIPTION).
WARNING: USE AN OSHA APPROVED RESPIRATOR
AND SAFETY GLASSES WHEN SPRAYING PAINT
OR SOLVENTS IN A CONFINED AREA. PERSONAL
INJURY CAN RESULT.
TOUCH UP PROCEDURE
(1) Scrape loose paint and corrosion from inside
scratch or chip.
(2) Clean affected area with Mopar
t Tar/Road Oil
Remover, and allow to dry.
(3) Fill the inside of the scratch or chip with a coat
of filler/primer. Do not overlap primer onto good sur-
face finish. The applicator brush should be wet
enough to puddle-fill the scratch or chip without run-
ning. Do not stroke brush applicator on body surface.
Allow the filler/primer to dry hard.
(4) Cover the filler/primer with color touch up
paint. Do not overlap touch up color onto the original
color coat around the scratch or chip. Butt the new
color to the original color, if possible. Do not stroke
applicator brush on body surface. Allow touch up
paint to dry hard.
(5) On vehicles without clearcoat, the touch up
color can be lightly finesse sanded (1500 grit) and
polished with rubbing compound.
(6) On vehicles with clearcoat, apply clear top coat
to touch up paint with the same technique as
described in Step 4. Allow clear top coat to dry hard.
If desired, Step 5 can be performed on clear top coat.
WARNING: AVOID PROLONGED SKIN CONTACT
WITH PETROLEUM OR ALCOHOL – BASED CLEAN-
ING SOLVENTS. PERSONAL INJURY CAN RESULT.
FINESSE SANDING/BUFFING &
POLISHING
DESCRIPTION
Minor acid etching, orange peel, or smudging in
clearcoat or single-stage finishes can be reduced with
light finesse sanding, hand buffing, and polishing. If
the finish has been finesse sanded in the past,
it cannot be repeated. Finesse sanding opera-
tion should be performed by a trained automo-
tive paint technician.
CAUTION:
Do
not
remove
clearcoat
finish,
if
equipped. Basecoat paint must retain clearcoat for
durability.
LH
PAINT
23 - 77
SEATS
TABLE OF CONTENTS
page
page
SEATS
. . . . . . . . . . . . . . 79
FRONT ARMREST
. . . . . . . . . . . . . . . . . . 79
. . . . . . . . . . . . . . 79
HEADREST
. . . . . . . . . . . . . . . . . . . . . . . . . . . 80
. . . . . . . . . . . . . . . . . . . . . . . 80
INSTALLATION - AIRBAG EQUIPPED
HEADREST SLEEVE - AIRBAG EQUIPPED
INSTALLATION - AIRBAG EQUIPPED
FRONT SEAT
. . . . . . . . . . . . . . . . . . . . . . . . . . . 81
. . . . . . . . . . . . . . . . . . . . . . . 82
INSTALLATION - AIRBAG EQUIPPED
FRONT SEAT BACK
. . . . . . . . . . . . . . . . . . . . . . . . . . . 83
. . . . . . . . . . . . . . . . . . . . . . . 83
INSTALLATION - AIRBAG EQUIPPED
FRONT SEAT BACK COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . 85
. . . . . . . . . . . . . . . . . . . . . . . 85
INSTALLATION - AIRBAG EQUIPPED
SEAT BACK PANEL
INSTALLATION - AIRBAG EQUIPPED
FRONT SEAT CUSHION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
. . . . . . . . . . . . . . . . . . . . . . . . . 88
FRONT SEAT CUSHION COVER
. . . . . . . . . . . . . . . . . . . . 88
. . . . . . . . . . . . . . . . . 89
SEAT SIDE SHIELD
. . . . . . . . . . . . . . . 90
INSTALLATION - AIRBAG EQUIPPED
LUMBAR SUPPORT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
SEAT TRACK & RECLINER ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
. . . . . . . . . . . . . . . . . . . . . . . . . 91
REAR ARMREST
. . . . . . . . . . . . . . . . . . . . . 91
. . . . . . . . . . . . . . . . . 92
REAR SEAT BACK
. . . . . . . . . . . . . . . . . . . . . . . . . . . 93
. . . . . . . . . . . . . . . 93
. . . . . . . . . . . . . . . 93
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . 93
. . . . . . . . . . . . . . . . . . . . . . . 93
INSTALLATION - 60/40 SEAT COLLAR
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . 94
REAR SEAT BACK COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
. . . . . . . . . . . . . . . . . . . . . . . . . 95
REAR SEAT CUSHION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
. . . . . . . . . . . . . . . . . . . . . . . . . 95
REAR SEAT CUSHION COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
. . . . . . . . . . . . . . . . . . . . . . . . . 95
SEAT ADJUSTERS
INSTALLATION - AIRBAG EQUIPPED
23 - 78
SEATS
LH
SEATS
SPECIFICATIONS - TORQUE
TORQUE SPECIFICATIONS
DESCRIPTION
N·m
Ft.
Lbs.
In.
Lbs.
Front seat track to floor pan bolts
61
45
—
Front seat inboard and outboard
pivot bolts
30
23
—
Front seat recliner to seat cushion
frame
12
9
—
Front seat track to cushion frame
bolt
12
9
—
Front seat back
40
30
—
Front seat back to seat cushion
30
22
—
Front seat back recliner to seat
back
8
—
71
Front seat rear outboard seat track
to floor pan bolts
28
20
—
Front seat airbag module to seat
back frame
7
—
62
Rear seat center seat belt retractor
to shelf
60
44
—
FRONT ARMREST
REMOVAL - 50/50 SPLIT
(1) Move the driver seat full forward and the pas-
senger seat full rearward.
(2) Open arm rest lid (Fig. 1).
(3) Remove access retaining nut cover.
(4) Remove arm rest retaining nut.
(5) Slide arm rest off of bracket (Fig. 2).
INSTALLATION - 50/50 SPLIT
(1) Slide arm rest on bracket.
(2) Install arm rest nut. Tighten nut to 25 N·m (18
ft. lbs.) torque.
(3) Install access retaining nut cover.
(4) Reposition the seats.
Fig. 1 ARM REST ACCESS HOLE
1 - REMOVE ACCESS HOLE
2 - NUT
3 - ARM REST
4 - COVER
Fig. 2 ARM REST BRACKET
1 - ARMREST BRACKET
LH
SEATS
23 - 79
HEADREST
REMOVAL
REMOVAL
(1) Lower head restraint slightly.
(2) Insert a stiff wire into the hole on the right
hand side head restraint sleeve/guide and push to
release latch (Fig. 3).
(3) At the same time, press the button on the head
restraint sleeve/guide left hand side and pull upward
to release the head restraint.
(4) Remove head restraint from seat back.
REMOVAL - AIRBAG EQUIPPED
WARNING: DISCONNECT AND ISOLATE THE NEGA-
TIVE
BATTERY
CABLE
REMOTE
TERMINAL
BEFORE BEGINNING ANY FRONT SEAT REMOVAL
OR INSTALLATION PROCEDURE. THIS WILL DIS-
ABLE THE AIRBAG SYSTEM. FAILURE TO DISCON-
NECT
THE
BATTERY
COULD
RESULT
IN
ACCIDENTAL AIRBAG DEPLOYMENT AND POSSI-
BLE PERSONAL INJURY.
WARNING: ONCE THE NEGATIVE CABLE IS DIS-
CONNECTED
WAIT
FOR
2
MINUTES
BEFORE
REMOVING ANY AIRBAG SYSTEM COMPONENTS.
(1) Disconnect the remote negative battery cable.
(2) If fully extended, lower head restraint slightly.
(3) Insert a stiff wire into the hole on the right
hand side head restraint sleeve/guide and push to
release latch (Fig. 4).
(4) At the same time, press the button on the head
restraint sleeve/guide and pull upward to release the
head restraint.
(5) Remove head restraint from seat back.
INSTALLATION
INSTALLATION
(1) Place head restraint in position.
(2) Push head restraint down into the lock posi-
tion.
(3) Raise head restraint to ensure it locks at the
last stop.
INSTALLATION - AIRBAG EQUIPPED
(1) Place head restraint in position.
(2) Push head restraint down into the lock posi-
tion.
(3) Raise head restraint to ensure it locks at the
last stop.
(4) Connect the remote negative battery cable.
Fig. 3 HEAD RESTRAINT REMOVAL
1 - SLEEVE GUIDE
2 - BUTTON
3 - STIFF WIRE
Fig. 4 HEAD RESTRAINT REMOVAL
1 - SLEEVE GUIDE
2 - BUTTON
3 - STIFF WIRE
23 - 80
SEATS
LH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст