Chrysler Town & Country/Voyager, Dodge Caravan, Plymouth Voyager. Manual — part 87
(9) Mark torque converter and drive plate with
chalk, for reassembly. Remove torque converter mount-
ing bolts.
(10) Disconnect electrical connectors at PRNDL
switch and neutral safety switch (Fig. 4).
(11) Remove front engine mount insulator and
bracket.
(12) On vehicles equipped with D.I.S.ignition sys-
tem, remove crankshaft position sensor from bell hous-
ing (Fig. 6). For installation procedure refer to section
8D of this service manual.
CAUTION: Failure to remove the crankshaft position
sensor from the bell housing could cause damage to
the sensor or the torque converter drive plate during
transmission removal or installation.
(13) Disconnect and remove vehicle distance sensor
(Fig. 7).
(14) Remove starter bolts and set starter aside. Do
not allow the starter to hang from battery cable (Fig.
8).
(15) Position transmission jack securely under tran-
saxle (Fig. 9).
(16) With transmission jack in position, remove the
left transmission mount (Fig. 10).
(17) Carefully lower the transaxle assembly from
vehicle.
When installing transaxle, reverse the above proce-
dure.
Check and/or adjust gear shift cable.
Refill transaxle with MOPAR
t ATF PLUS (Auto-
matic Transmission Fluid) Type 7176 or equivalent.
Fig. 4 Disconnect PRNDL Switch and Neutral Safety
Switch
Fig. 5 Remove Front Engine Mount
Fig. 6 Remove Crank Position Sensor (D.I.S. Ignition
Only)
Fig. 7 Remove Distance Sensor
.
TRANSAXLE
21 - 97
SOLENOID ASSEMBLY-REPLACE
Fig. 8 Remove Starter Assembly
Fig. 9 Position Transmission Jack
Fig. 10 Remove Left Transmission Mount
Fig. 11 Lower Transaxle Assembly
Fig. 1 Input Speed Sensor
Fig. 2 Input Speed Sensor Removed
21 - 98
TRANSAXLE
.
PRNDL SWITCH
CAUTION: Switch seal washer must be seated prop-
erly before tightening switch. Failure to do so may
result in leakage of transmission fluid.
NEUTRAL SAFETY SWITCH
CAUTION: Switch seal washer must be seated prop-
erly before tightening switch. Failure to do so may
result in leakage of transmission fluid.
SPEED SENSOR-INPUT
CAUTION: When disconnecting speed sensor con-
nector, be sure that the weather seal does not fall off
or remain in old sensor.
The input speed sensor is located to the right of the
manual shift lever.
SPEED SENSOR-OUTPUT
The output speed sensor is located to the left of the
manual shift lever (Fig. 8).
CAUTION: When disconnecting speed sensor con-
nector, be sure that the weather seal does not fall off
or remain in old sensor.
Fig. 3 Sound Cover
Fig. 4 Attaching Screws
Fig. 5 Solenoid Assembly
Fig. 6 PRNDL Switch
Fig. 7 Neutral Safety Switch
.
TRANSAXLE
21 - 99
TRANSAXLE-RECONDITION
Prior to removing any transaxle subassemblies, plug
all openings and thoroughly clean exterior of the unit,
preferably by steam. Cleanliness through entire disas-
sembly and assembly cannot be overemphasized. When
disassembling, each part should be washed in a suit-
able solvent, then dried by compressed air. Do not
wipe parts with shop towels. All mating surfaces in
the transaxles are accurately machined; therefore,
careful handling of all parts must be exercised to avoid
nicks or burrs.
Fig. 8 Output Speed Sensor
Fig. 1 Oil Pan Bolts
Fig. 2 Oil Pan
Fig. 3 Oil Filter
Fig. 4 Valve Body Attaching Bolts
21 - 100
TRANSAXLE
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст