SsangYong Korando II (1996-2006 year). Manual — part 432
INSTRUMENTATION, DRIVER INFORMATION 9E-9
SSANGYONG MY2002
INSTRUMENT CLUSTER INDICATOR LAMPS
Instrument Cluster Indicator Lamps Do Not Operate
Step
1
2
3
4
5
6
7
8
9
Action
Is fuse F30 blown?
1. Check for a short circuit and repair if necessary.
2. Replace the blown fuse.
Is the relpair complete?
1. Turn the ignition ON.
2. Check the votage at fuse F30.
Does the battery voltage match the value specified?
Repair the open power supply circuit to fuse F30.
Is the repair complete?
1. Remove the instrument cluster.
2. Disconnect the instrument cluster connectors A1.
3. Turn the ignition ON.
Does the battery voltage match the value specified?
Repair the open circuit between fuese F30 and the
instrument cluster connectors A1.
Is the repair complete?
Check the instrument cluster warning lamp bulbs.
Are the bulbs OK?
1. Replace any warning lamp bulbs that were
defective.
2. Check the charging system to make sure the
alternator is not overcharging.
3. Repair the charging system if necessary.
Is the repair complete?
Replace the instrument cluster.
Is the repair complete?
Yes
Go to Step 2
System OK
Go to Step 5
System OK
Go to Step 7
System OK
Go to Step 9
System OK
System OK
No
Go to Step 3
-
Go to Step 4
-
Go to Step 6
-
Go to Step 8
-
-
Value(s)
-
-
11 - 14 v
-
11 - 14 v
-
-
-
-
SSANGYONG MY2002
9E-10 INSTRUMENTATION, DRIVER INFORMATION
COOL
HOT
KAA9E030
KAA9E040
CENTER FACIA
Removal and Installation Procedure
1. Remove the floor console. Refer to Section 9G,
Floor Console
2. Remove the center tray. Refer to “Center Tray” in
this section.
3. Remove the center facia with the screws.
4. Installation should follow the removal procedure
in the reverse order.
ASHTRAY
Removal and Installation Procedure
1. Remove the center facia. Refer to “Center Facia”
in this section.
2. Remove the ashtray assembly from the center
facia.
3. Installation should follow the removal procedure
in the reverse order.
KAA9E020
ON-VEHICLE SERVICE
UNIT REPAIR
CENTER TRAY
Removal and Installation Procedure
1. Pull the center tray.
2. Installation should follow the removal procedure
in the reverse order.
REPAIR INSTRUCTIONS
INSTRUMENTATION, DRIVER INFORMATION 9E-11
SSANGYONG MY2002
KAA9E060
KAA9E070
CUP HOLDER
Removal and Installation Procedure
1. Remove the center facia. Refer to “Center Facia”
in this section.
2. Remove the cup holder with the screws.
3. Installation should follow the removal procedure
in the reverse order.
KAA9E050
CIGAR LIGHTER
Removal and Installation Procedure
1. Removed the floor console. Refer to “floor
console” in this section.
2. Remove the center tray. Refer to “Center tray” in
this section.
3. Remove the center facia with the screws. Refer to
“Center Facia” in this section.
4. Remove the ashtray assembly with the screws.
Refer to “Ashtray” in this section.
5. Disconnect the cigar lighter connector.
6. Turn the cigar lighter locker and remove.
7. Installation should follow the removal procedure
in the reverse order.
INSTRUMENT PANEL VENT
Removal and Installation Procedure
1. Remove the center facia. Refer to “Center Facia”
in this section.
2. Remove the instrument panel vents from the center
facia.
3. Installation should follow the removal procedure
in the reverse order.
SSANGYONG MY2002
9E-12 INSTRUMENTATION, DRIVER INFORMATION
KAA9E090
KAA9E100
KAA9E110
3. Remove the glove box with the screws
4. Installation should follow the removal procedure
in the reverse order.
HOOD LATCH RELEASE HANDLE
Removal and Installation Procedure
1. Remove the hood latch release handle with the
screws.
2. Installation should follow the removal procedure
in the reverse order.
KAA9E080
GLOVE BOX
Removal and Installation Procedure
1. Remove the side facia panel. Refer to “Side Facia
Panel” in this section.
2. Pull and remove the glove box stopper of both.
CHIME MODULE
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the center tray. Refer to “Center tray” in
this section.
3. Remove the center facia. Refer to “Center Facia”
in this section.
4. Remove the cup holder. Refer to “Cup Holder” in
this section.
5. Remove the chime module with the screws
6. Installation should follow the removal procedure
in the reverse order.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст