SsangYong Korando II (1996-2006 year). Manual — part 207
WHEEL ALIGNMENT 2B-7
SSANGYONG MY2002
VEHICLE HEIGHT
Adjustment Procedure
1. Check the tire for proper inflation.
2. Measure ‘A’ from the center of the lower arm
rear mounting bolt end to the ground.
KAA2B050
3. Measure ‘B’ from the center of the steering
knuckle shaft to the ground.
KAA2B060
4. If the difference between ‘A’ and ‘B’ is not
within specification, adjust vehicle height using
torsion bar height control bolt.
Adjustment Notice
Specification
31 - 36 mm
(1.22 - 1.42 inch)
B - A
Notice: Before wheel alignment, adjust vehicle
height adjustment first.
KAA2B070
FRONT TOE-IN ADJUSTMENT
Adjustment Procedure
1. Disconnect the outer tie rods from the knuckle as-
semblies. Refer to Section 6C, Power Steering
Gear.
2. Loosen the front toe adjusting nut.
Notice: In this adjustment, the right and the left tie
rods must be equal in length, or the tires will wear
unevenly.
3. Turn the right and the left outer tie rods to align the
toe to the proper specifications. Refer to “Wheel
Alignment Specifications” in this section.
KAA2B080
4. Hold the outer tie rod and tighten the front toe adjust-
ing nut.
Adjustment Notice
Tightening Torque
73 N•m (54 lb-ft)
5. Reconnect the outer tie rods to the knuckle assem-
blies. Refer to Section 6C, Power Steering Gear.
SSANGYONG MY2002
2B-8 WHEEL ALIGNMENT
FRONT CAMBER CHECK
Adjustment Procedure
1. Remove the free wheel hub.
2. M e a s u r e c a m b e r w i t h a w h e e l a l i g n m e n t
equipment.
Adjustment Notice
Specification
0° ± 30
′
KAA2B090
3. I f c a m b e r m e a s u r e m e n t s a r e n o t w i t h i n
specification, adjust it by increasing or decreasing
the number of adjusting shims inserted between
the upper arm shaft and cross bracket.
Adjustment Notice
KAA2B100
Notice: Difference between the left and right should
be adjusted within 30
′
.
FRONT CASTER CHECK
Adjustment Procedure
1. Remove the free wheel hub.
2. Measure caster with a wheel alignment equipment
and a turning radius gauge.
Adjustment Notice
Specification
2°30
′
± 30
′
KAA2B090
3. I f c a s t e r m e a s u r e m e n t s a r e n o t w i t h i n
specification, adjust it by increasing 1EA (rear) or
decreasing 1EA (front).
Adjustment Notice
Adjusting Shims
Increasing
1EA
Decreasing
1EA
Front
Rear
0.4 Small
1.6 Small
0.4 Small
1.6 Small
+11
′
+43
′
-11
′
-43
′
-11
′
-43
′
+11
′
+43
′
Notice: Difference between the left and right
should be adjusted within 30
′
.
KAA2B100
Adjusting
Shims
1.6 Large
3.2 Large
Increasing 1EA
+19
′
+38
′
Decreasing 1EA
-19
′
-38
′
WHEEL ALIGNMENT 2B-9
SSANGYONG MY2002
Application
Camber
Caster
King Pin Inclination
Toe-in (No load)
Rear
-
-
-
-
SPECIFICATIONS
WHEEL ALIGNMENT SPECIFICATIONS
Front
0° ± 30
′
2°30
′
± 30
′
12°30
′
0 - 4 mm
54
Front Toe Adjusting Nut
N
l
m
Application
Lb-In
FASTENER TIGHTENING SPECIFICATIONS
Lb-Ft
73
-
SECTION 2C
FRONT SUSPENSION
TABLE OF CONTENTS
Components Locator . . . . . . . . . . . 2C-2
Diagnostic Information and Procedures . . . .. 2C-3
Ball Joint Inspection . . . . . . . . . . . 2C-3
Repair Instructions . . . . . . . . . . . . 2C-4
On-Vehice Service . . . . . . . . . . . . .. 2C-4
Front Hub Bearing Assembly . . . . . . . ... 2C-4
Front Stabilizer . . . . . . . . . . . . . . 2C-5
Stabilizer Link . . . . . . . . . . . . . .. 2C-6
Torsion Bar . . . . . . . . . . . . . . .. 2C-7
Lower Control Arm . . . . . . . . . . . ... 2C-7
Upper Control Arm . . . . . . . . . . . ... 2C-8
Front Shock Absorber . . . . . . . . . . .. 2C-9
Lower Ball Joint . . . . . . . . . . . . . 2C-10
Upper Ball Joint . . . . . . . . . . . . . 2C-10
Knuckle Assembly . . . . . . . . . . . . 2C-11
Crossmember . . . . . . . . . . . . . 2C-12
Unit Repair . . . . . . . . . . . . . . .. 2C-14
Hub and Bearing . . . . . . . . . . . ... 2C-14
Specifications . . . . . . . . . . . . . . 2C-16
Fastener Tightening Specifications . . . . . . 2C-16
Special Tools and Equipment . . . . . . . . 2C-17
Special Tools Table . . . . . . . . . . . . 2C-17
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст