SsangYong Korando II (1996-2006 year). Manual — part 311

AUTOMATIC TRANSMISSION 5A-147

SSANGYONG MY2002

DTC P1745 Solenoid 5 Circuit Short

Test Description

The number(s) below refer to the step number(s) on
the Diagnostic Table.

3. Checks if the S5 circuit in the transmission is mal-

functioning.

4. Check cable in the transmission for short to

ground.

6. Check resistance between S5 terminal A and B.

Standard value is 3.6 - 5.5

Ω

.

10. Check connections of other connectors.

-

Go to Step 12

-

1

Perform Transmission Control Module (TCM) System
Check.
Is the check performed?
1. Install the scan tool.
2. Turn the ignition ON, with the engine OFF.
3. Record and then clear DTCs.
4. Operate the vehicle within the conditions for

setting this DTC as specified in the text.

Does the scan tool display P1745?
1. Turn the ignition OFF.
2. Disconnect the 10-way transmission connector.

(additional DTCs will set)

3. Connect Solenoid/Thermistor Electrical Tester

(STET) to the 10-way transmission connector of
transmission side.

4. Turn the mode knob of STET to 5 and push the red

button.

Does the bulb of close circuit on the solenoids side of
STET illuminate?
1. Remove the valve cover. Refer to the Transmission

in this section.

2. With a test light connected to B+ probe the wiring

harnesses from 10-way transmission connector to
Solenoid 5 (S5) on the valve body.

Does the test light illuminate?
Repair the short to ground in the wiring harness.
Is the repair complete?
Using a Digital Volt Meter (DVM), measure the resis-
tance between S5 terminal A and B.
Is the resistance within the specified value?
Replace the S5.
Is the action complete?
1. Disconnect the TCM connector A.
2. With a test light connected to B+, probe the wiring

harness from 10-way transmission connector
terminal 5 to TCM terminal.

Does the test light illuminate?
Probe the wiring harness from 10-way transmission
connector terminal 8 to TCM terminal A1.
Does the test light illuminate?
Check for a poor connection at the 10-way transmission
connector and TCM connector and repair the malfunc-
tioning terminals as necessary.
Is a repair necessary?

Step

Action

Value(s)

Yes

No

2

3

-

Go to Step 2

Go to “TCM

Diagnostic

System Check”

-

Go to Step 4

Go to Step 8

5

6

4

-

Go to Step 5

Go to Step 6

-

Go to Step 12

-

7

8

9

-

Go to Step 5

Go to Step 9

10

-

Go to Step 5

Go to Step 10

-

Go to Step 12

Go to Step 11

-

Go to Step 3

Go to

“Diagnostic

Aids”

3.6 - 5.5

Ω

Go to

“Diagnostic

Aids”

Go to Step 7

5A-148 AUTOMATIC TRANSMISSION

SSANGYONG MY2002

DTC P1745 Solenoid 5 Circuit Short (Cont’d)

1. Turn the ignition OFF.
2. Replace the TCM.
Is the action complete?
1. Using the scan tool, clear the DTCs.
2. Road test the vehicle within the conditions for

setting this DTC as specified in the text.

Does the scan tool indicate that this diagnostic has
run and passed?
Check if any DTCs are set.
Are any there DTCs displayed or previously recorded
at Step 2 that have not been diagnosed?

Step

Action

Value(s)

Yes

No

12

-

Go to Step 13

Go to Step 2

13

-

Go to

applicable

DTC table

System OK,

Check

Complete

-

Go to Step 12

-

11

AUTOMATIC TRANSMISSION 5A-149

SSANGYONG MY2002

BLANK

AUTOMATIC TRANSMISSION 5A-157

SSANGYONG MY2002

ON-VEHICLE SERVICE

TRANSMISSION

Removal and Installation Procedure

1. Disconnect the negative battery cable.

2. Disconnect the connectors from transfer case.

3. Disconnect the speedometer connector from

transfer case.

4. Disconnect the inhibitor connector, gear position

sensor connector and transmission case connector.

REPAIR INSTRUCTIONS

5. Remove the rear propeller shaft bolts.

Installation Notice

6. Remove the cross member bolts and nuts.

Installation Notice

KAA5A2I0

Tightening Torque

70 - 80 N•m

(52 - 59 lb-ft)

Tightening Torque

70 - 80 N•m

(52 - 59 lb-ft)

KAA5A2H0

KAA5A2J0