SsangYong Musso. Manual — part 473
AUTOMATIC TRANSMISSION 5A-69
MECHANICAL TESTS
In Vehicle Transmission Checks
Carry out the following tests before removing the transmission.
!
See Checking Transmission Fluid Level, Section 7.2.1.
!
Check that the transmission oil is not burnt (colour and smell are correct).
!
Ensure that the transmission is not in limp home mode (LHM).
!
Check that the battery terminals and the earth connections are not corroded or loose.
!
Check the engine stall speed is within the handbook value.
!
Check that the cooler flow is not restricted.
!
Check that all electrical plug connections are tight.
!
Carry out a road test to confirm the symptoms, if necessary.
!
Inspect the oil, ensure that there are no metal or other contaminants in the oil pan.
Diagnosing Oil Leaks
Determine the source of oil leaks by firstly cleaning down the affected area, then driving the vehicle.
Inspect the seals to confirm the source of the leak.
!
To determine the source of a rear servo oil leak, raise the vehicle on a hoist, then carry out a reverse stall.
!
To determine the source of a front servo leak, raise the vehicle on a hoist, then run the vehicle in second gear.
Troubleshooting Charts
The troubleshooting charts are set out as follows:
!
Table 6.2.1 Drive Faults,
!
Table 6.2.2 Faulty Shift Patterns.
!
Table 6.2.3 Shift Quality Faults.
!
Table 6.2.4 After Teardown Faults.
Table 6.2.1 - Drive Faults
Action
Check the fluid level. Top up as necessary.
Inspect and clean C1/C2 feed.
Reinstall/renew the ‘z’ link.
Remove, clean and re-install the PRV.
Inspect and replace as necessary.
Inspect and replace as necessary.
Inspect and replace as necessary.
Check servo adjustment or replace rear band
as necessary.
Check for failure in C3, C3 hub or C1/C2 cylin-
der. Repair as necessary.
Inspect and clean PRV.
Inspect and replace pump gears as necessary.
Inspect and repair as necessary.
Possible Cause
Insufficient auto transmission fluid.
Blocked feed in C1/C2 cylinder.
‘Z’ link displaced.
Primal regulator valve (PRV) jammed open.
Overdrive shaft or input shaft seal rings
failed.
3-4 or 1-2 one way clutch (OWC) installed
backwards or failed.
C2 piston broken or cracked.
Rear band or servo faulty.
Failure in C3, C3 hub or C1/C2 cylinder.
Jammed primary regulator valve (PRV).
Damaged/broken pump gears.
Dislodged output shaft snap ring.
Symptom
No Drive in D
No Drive in
Reverse
No engine braking
in Manual 1
Engine braking in
Manual 1 is OK
No drive in Drive
and Reverse
5A-70 AUTOMATIC TRANSMISSION
Action
Inspect S1. Repair or replace as necessary.
Check for 12 Volts applied to S1 at all times or
for wiring fault.
Inspect S1. Repair or replace as necessary.
Check for 12 Volts applied to S1 at all times or
for wiring fault.
Inspect S2. Repair or replace as necessary.
Check for open circuit or wiring fault.
Inspect S2. Repair or replace as necessary.
Check for open circuit or wiring fault.
Inspect and adjust as necessary.
Inspect and repair as necessary.
Inspect and replace or refit as necessary.
Inspect ‘O’ ring. Refit or replace as necessary.
Inspect the 2-3 shift valve. Repair or replace
as necessary.
Inspect C1 clutch. Repair or replace as neces-
sary.
Inspect ball. Refit or replace as necessary.
Inspect C4. Repair C4 or replace C4 wave plate
as necessary.
Inspect rear band adjustment. Adjust as nec-
essary.
Inspect ball- Refit or replace as necessary.
Inspect’0’ring. Refit or replace as necessary.
Inspect C4 and C4 wave plate. Repair or re-
place as necessary.
Inspect inhibitor switch.
Repair or replace as necessary.
Inspect the 1-2 shift valve.
Repair or replace as necessary
Inspect inhibitor switch.
Repair or replace as necessary.
Inspect the 2-3 shift valve.
Repair or replace as necessary.
Possible Cause
S1 always OFF.
S1 always ON.
S2 always OFF.
S2 always ON.
B1 failed.
Loose band adjustment.
Front servo piston or seal failed.
S1/S2 ball misplaced,
Smaller’0’ring on front servo piston failed
or missing.
2-3 shift valve jammed.
C1 clutch failed or slipping in 3rd and 4th.
(Gives 1st in 3rd and 2nd in 4th.)
Over-run clutch (OC)/low ball misplaced.
C4 failed or C4 wave plate broken.
Rear band slipping when hot.
Reverse/Low-1st ball misplaced.
Rear servo inner ‘O’ ring missing.
C4 failed or C4 wave plate broken.
Inhibitor switch faulty.
1-2 shift valve jammed.
Inhibitor switch fault, 1-2 only.
2-3 shift valve jammed.
Symptom
2-3 shift only
(no 4th or 1st)
1-4 shift only
1-3-4 (Delayed
1-2shift)
4-3 shift only
1-2-Neutral
(1st over run)
1-3 shift only
1-3-4 only
1-2-1 only
No manual 4-3,3-2
or 2-1
No manual 1st
1st gear only or
2nd,3rd, and 4th
only
1st and 2nd only
or 1st, 3rd and 4th
only
AUTOMATIC TRANSMISSION 5A-71
Table 6.2.2 - Faulty Shift Patterns
Action
Inspect inhibitor switch. Repair or replace as
necessary.
Inspect the 3-4 shift valve. Repair or replace
as necessary.
Inspect the release valve. Repair or replace as
necessary.
Inspect S3 or S2. Repair or replace as neces-
sary.
Inspect the regulator valve. Repair or replace
as necessary.
Inspect the ball. Refit or replace as necessary.
Inspect the sealing rings. Refit or replace as
necessary.
Inspect the ‘O’ rings. Refit or replace as neces-
sary.
Inspect the bleed ball. Refit or replace as nec-
essary.
Inspect S1 or S4. Repair or replace as neces-
sary.
Inspect the release valve. Repair or replace as
necessary.
Inspect the band. Adjust as necessary.
Inspect the ‘O’ rings. Refit or replace as neces-
sary.
Inspect S5. Repair or replace as necessary.
Inspect the regulator valve. Repair or replace
as necessary.
Possible Cause
Inhibitor switch fault, 1-2-3 only.
3-4 shift valve jammed.
Jammed band 1 release valve.
Faulty S3 or S2 solenoid.
Faulty clutch apply regulator valve.
Missing or damaged clutch apply feed ball.
Damaged input shaft sealing rings.
Damaged C1 piston ‘O’ rings.
Damaged or dislodged C1 piston bleed
ball.
Faulty S1 or S4 solenoid.
Jammed band 1 release valve.
Incorrect front band adjustment.
Damaged front servo piston ‘O’ rings.
Faulty or damaged variable pressure
solenoid (S5).
Faulty band apply regulator valve.
Symptom
1st,2nd and 4th
only or 1st,2nd,
and 3rd (tied up in
3rd)
Harsh 2-3 shift
Harsh 3-4 shift
5A-72 AUTOMATIC TRANSMISSION
Action
Drain and fill with specified ATF.
Check that S5 is fitted correctly, or replace S5.
Inspect band apply and clutch apply regulator
springs. Refit or replace as necessary.
Inspect the ball. Refit or replace as necessary.
Inspect C4 clutch. Replace or repair as neces-
sary.
Check the alignment. ]Realign as necessary.
Inspect wave plate. Replace as necessary.
Inspect S5 and replace as necessary.
Inspect the damper spring and replace as nec-
essary.
Replace spring as necessary.
Check the clearance and adjust as necessary.
Inspect C4. Repair or replace as necessary.
Inspect piston. Repair or replace as necessary.
Inspect and adjust band as necessary.
Replace the plug.
Replace the spring.
Replace the spring/plug.
Refit the ball.
Inspect the clutch. Repair the clutch as neces-
sary.
Inspect and clean C1 feed.
Replace the piston.
Inspect and replace the sealing rings and/or
shaft as necessary.
Inspect and replace the ball.
Inspect and replace the sealing rings and/or
shaft as necessary.
Inspect and repair the C1 clutch as necessary.
Refit the valve.
Replace the ball.
Possible Cause
Incorrect auto transmission fluid (ATF).
S5 faulty won, or incorrectly fitted.
Band apply and clutch apply regulator
springs misplaced.
Over-run clutch (OC)/Low-1st ball
misplaced.
C4 clutch worn or burnt.
C4 wave plate not lined up with the holes
in the piston.
C4 wave plate failed.
S5 worn.
S5 damper spring broken.
Front servo belleville spring broken.
Incorrect C4 pack clearance.
Damaged C4 clutch.
Cracked C2 piston (leaking into C4).
Incorrect band adjustment
Front servo plastic plug missing
B1R spring broken.
B1R spring/plug left out.
C1/B1R ball misplaced.
C1 clutch damaged.
Restriction in C1 feed.
C1 piston check ball jammed.
Overdrive or input shaft sealing rings dam-
aged.
C1/B1R ball misplaced.
Overdrive or input shaft sealing rings dam-
aged.
C1 clutch damaged.
4-3 sequence valve in backwards.
Low-1st check ball misplaced.
Symptom
All Shifts Firm
Manual 4-3-2-1 is
soft delayed or
missing
Firm 1-2 Hot
4th Tied up
Tied up on 2-3
Flare on 2-3
Slips in 4th
Flare on 4-3, Flare
on 3-2
Firm Manual low
shift-high line
press.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст