SsangYong Musso. Manual — part 210
1F-424 ENGINE CONTROLS
SSANGYONG Y158
FUEL FILTER
Removal and Installation Procedure
1. Disconnect the negative battery cable.
Caution: The fuel system is under pressure. To avoid
fuel spillage and the risk of personal injury or fire, it
is necessary to relieve the fuel system pressure
before disconnecting the fuel lines.
2. Relieve the fuel system pressure. Refer to
"Discharging the Pressure in Fuel System" in this
section.
3. Disconnect the fuel lines from the fuel filter
Installation Notice
4. Remove the fuel filter mounting bracket bolt.
Installation Notice
Notice: Place the fuel pump pad. There may be a corrosion
due to the contact between the fuel filter and the bracket.
5. Remove the fuel filter.
6. Install the fuel filter.
7. Perform a leak test of the fuel filter.
8. Installation should follow the removal procedure in
the reverse order.
FUEL TANK
Removal and Installation Procedure
Caution: The fuel system is under pressure. To avoid
fuel spillage and the risk of personal injury or fire, it
is necessary to relieve the fuel system pressure
before disconnecting the fuel lines.
1. Relieve the fuel pressure. Refer to "Discharging the
Pressure in Fuel System" in this section.
2. Disconnect the negative battery cable.
3. Drain the fuel tank.
4. Put aside the floor carpet to remove the fuel pump
access cover.
5. Remove the fuel pump access cover.
Tightening Torque
28 N•m (21 lb-ft)
Tightening Torque
6 N•m (53 lb-ft)
YAA1F190
KAA1F370
ENGINE CONTROLS 1F-425
SSANGYONG Y158
YAA1F700
YAA1F180
6. Disconnect the return line.
7. Disconnect the supply line.
8. Disconnect the fuel tank-to-canister hose from the
fuel tank.
9. Disconnect the fuel pump wiring connector.
10. Disconnect the fuel filler hose and air vent hose from
the fuel tank.
11. Support the fuel tank.
12. Remove the fuel tank retaining nuts.
Installation Notice
13. Carefully lower the fuel tank.
14. Turn the roll over valves counterclockwise at an angle
of 90 degrees.
15. Turn the lock ring counterclockwise.
16. Remove and discard the gasket.
17. Installation should follow the removal procedure in
the reverse order.
FUEL PRESSURE REGULATOR
(2.3L DOHC)
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the fuel pressure test connector
Installation Notice
Tightening Torque
38 N•m (28 lb-ft)
Tightening Torque
25 N•m (18 lb-ft)
YAA1F170
YAA1F160
YAA1F180
YAA1F700
1F-426 ENGINE CONTROLS
SSANGYONG Y158
KAA1F440
KAA1F430
YAA1F730
YAA1F720
Caution: The fuel system is under pressure. To avoid
fuel spillage and the risk of personal injury or fire, it
is necessary to relieve the fuel system pressure
before disconnecting the fuel lines.
3. Relieve the fuel pressure in fuel supply system by
pressing the service valve.
4. Disconnect the vacuum hose.
5. Disconnect the circlip and remove the fuel pressure
regulator.
6. Apply the oil to O-ring lightly and then replace it.
7. Perform a leak test of the fuel pressure regulator
with the engine off and the ignition on.
8. Installation should follow the removal procedure in
the reverse order.
FUEL PRESSURE REGULATOR
(3.2L DOHC)
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the fuel pressure test connector
Installation Notice
Caution: The fuel system is under pressure. To avoid
fuel spillage and the risk of personal injury or fire, it
is necessary to relieve the fuel system pressure
before disconnecting the fuel lines.
3. Relieve the fuel pressure in fuel supply system by
pressing the service valve.
Tightening Torque
25 N•m (18 lb-ft)
YAA1F270
YAA1F730
KAA1F430
KAA1F440
ENGINE CONTROLS 1F-427
SSANGYONG Y158
KAC1F250
YAA1F710
KAA1F130
4. Disconnect the vacuum hose.
5. Disconnect the circlip and remove the fuel pressure
regulator.
6. Apply the oil to O-ring lightly and then replace it.
7. Perform a leak test of the fuel pressure regulator with
the engine off and the ignition on.
8. Installation should follow the removal procedure in
the reverse order.
FUEL RAIL AND INJECTORS
(2.3L DOHC)
Removal and Installation Procedure
Caution: The fuel system is under pressure. To avoid
fuel spillage and the risk of personal injury or fire, it
is necessary to relieve the fuel system pressure
before disconnecting the fuel lines.
1. Discharge the fuel pressure from the fuel pressure
test connector.
2. Disconnect the negative cable.
3. Disconnect the vacuum hose from the fuel pressure
regulator.
4. Disconnect the Intake Air Temperature (IAT) sensor
connector.
5. Remove the intake air duct clamps.
6. Remove the intake air duct.
KAA1F130
YAA1F710
KAC1F250
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст