SsangYong Korando III (2010 year). Manual — part 189
06-43
8510-00
Tailgate open
▶
When pressing the tailgate switch for more than 0.1 second with driver door unlocked and vehicle
speed below 3 (±0.1) km/h, the tailgate open relay is turned ON for about 1 second, with
power OFF, ACC ON or IGN ON. However, it is turned ON when the vehicle speed is below 3
(±0.1) km/h, with IGN ON.
The tailgate open relay is turned OFF immediately after the driver door is locked or the vehicle speed
goes over 3 km/h with IGN ON during its operation. However, the BCM does not operate if the tailgate
open switch is pressed when the vehicle speed is above 3 km/h.
1.
2.
Tailgate open: REKES unlock (disarmed deterrent mode) → Tailgate open signal → Tailgate
open
-
Without SKM
When pressing the tailgate switch for more than 0.1 second with driver door unlocked and vehicle
speed below 3 (±0.1) km/h, the tailgate open relay is turned ON for about 1 second.
The tailgate open relay is turned OFF immediately after the driver door is locked or the vehicle speed
goes over 3 km/h during its operation.
When the tailgate switch on smart key is pressed in theft deterrent mode or with the smart key
detected by the exterior antenna, the SKM verifies the smart key and disarms the tailgate only. When
the tailgate is open and closed, the system enters into the theft deterrent mode again. If the tailgate
switch is not operated for 30 seconds, the system also does so.
The BCM checks that the verified smart key is in the luggage room 1 second after when the closed
tailgate is detected by the tailgate open switch with power OFF.
If there is a verified smart key in the luggage room when the tailgate is open and closed in theft
deterrent mode, the external buzzer sounds for 5 seconds.
When the driver press the tailgate open switch in order to look for the smart key, the BCM deactivates
lock so that the tailgate can be opened even though the driver door is locked. (maintains standby for
opening without verification)
1.
2.
3.
4.
With SKM
07-2
1. LAMP SPECIFICATIONS
1) Exterior Lamps
Item
Type
Amount
Front lamp
Headlamp (high beam/low beam)
BULB: H4
2 EA
Turn signal lamp
BULB: PY21W
2 EA
Position lamp
BULB: W5W
2 EA
Fog lamp
BULB: H27W/2
2 EA
Rear lamp
Stop lamp and tail lamp
BULB: 12V27/8W (Korea)
P21/5W (Other countries)
2 EA
Turn signal lamp
BULB: 12V27W (Korea)
P21W (Other countries)
2 EA
Backup lamp
BULB: 12V27W (Korea)
P21W (Other countries)
2 EA
Stop lamp/Rear fog lamp
(Other countries)
BULB: 12V27W (Korea)
P21W (Other countries)
2 EA
High-mounted stop lamp
LED
(Without spoiler)
(With spoiler)
12 EA
24 EA
License plate lamp
BULB: W5W
2 EA
Side lamp
Side repeater lamp
LED
5 EA
Puddle lamp
LED
2 EA
2) Interior Lamps
Item
Type
Amount
Front room lamp
BULB (10W-FESTOON)
2 EA
Center room lamp
BULB (10W-FESTOON)
1 EA
Luggage lamp
BULB (10W-FESTOON)
1 EA
Sun visor lamp
BULB (5W-FESTOON)
1 EA
Glove box lamp
BULB (5W-FESTOON)
1 EA
Door courtesy lamp
BULB (5W-WEDGGE)
1 EA
Item
Type
Amount
Front lamp
Headlamp (high beam/low beam)
BULB: H4
2 EA
Turn signal lamp
BULB: PY21W
2 EA
Position lamp
BULB: W5W
2 EA
Fog lamp
FRT
BULB: H27W/2
2 EA
RR
BULB: H21W/2
2 EA
07-3
8310-00
Luminous intensity is a measure for the amount of light which passes through the unit area per
time unit. The SI unit of luminous intensity is the candela (cd), an SI base unit.
-
Luminous Intensity
▶
Luminance describes the amount of light that passes through or is emitted from a particular area,
and falls within a given solid angle. It is measured in sb or nt.
-
Luminance
▶
This indicates the amount of light reaching a given area. Measuring unit is lux (lx) and it is not
directly proportional to the brightness of the area as the reflection rate is not included.
-
Intensity of illumination
▶
The LED stands for "Light Emitting Diode" or "Luminescent Diode." LED is a semiconductor diode
that emits incoherent narrow-spectrum light when electrically biased in the forward direction of the
p-n junction, as in the common LED circuit. In short, it is an element that converts electric signals
into light signals. Yellow, blue, red and white LEDs are currently available.
The followings are the advantages of LED.
It is not glaring and doesn't have short circuit unlike the conventional lamps.
It is semi-permanent and doesn't generate heat.
Its power consumption is much lower than those of conventional bulbs.
-
-
▶ LED
Pin No.
Specification
Operating voltage
9 V to 16 V
Load
Max. 200 mA (relay load)
Operating temperature
-30℃ to 85℃
Storage temperature
-40℃ to ±120℃
Mounting location
Top center of inner side of windshield glass
2. AUTOMATIC LIGHT SENSOR SPECIFICATIONS
07-4
Puddle (approach) lamp
Front fog lamp
Headlamp
Side repeater lamp
High-beam
/low-beam
Turn signal lamp
Position lamp
1. EXTERIOR LAMP
1) Layout
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст