SsangYong Rexton. Manual — part 677
SSANGYONG Y200
9D-22 BODY ELECTRICAL
SWITCH OF MULTI – FUNCTION
YAD9D400
1 Multi - Function Switch Assembly
2 Turn Signal Switch Assembly
3 Turn Signal Switch Assembly
4 Screw
5 Switch of Light
6 Switch of Auto - Light
7 Connector
8 Switch of Wiper
BODY ELECTRICAL 9D-23
SSANGYONG Y200
Components of Connector Pin
Layout of connect
Number of pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Switch of turn signal (LH)
Power of flasher unit
Switch of turn signal (RH)
Power of head lamp upper beam
Switch passing of head lamp
Front washer switch
Wiper and washer ground
Auto wiper
Wiper parking
Ground of light switch
Auto light switch
Switch of head lamp
Switch of tail lamp
Ground of dimmer and passing switch
-
Low speed of wiper
High speed of wiper
Ground of intermittent wiper
Intermittent wiper
Horn relay
Name of connector
TL
TB
TR
HU
HS (2)
W
EW
AUTO
P
ES
A
HS (1)
TS
EB
-
LO
HI
ET
INT
HORN
YAD9D410
SSANGYONG Y200
9D-24 BODY ELECTRICAL
Check and Repair
Check applying of electric current below terminal at
each position of multi-function switch, if each terminals
are not applied of electric current, replace multi-function
switch.
YAD9D420
YAD9D450
YAD9D430
YAD9D440
YAD9D470
YAD9D460
Light switch
Dimmer and passing
Auto - light switch
Turn signal lamp
Wiper switch
Washer
BODY ELECTRICAL 9D-25
SSANGYONG Y200
Removal and Installation
Before multi-function switch is removed in the vehicle
with air bag, keep in mind the following.
Notice:
•
Do not separate module of air bag or coil of contact,
if malfunction of air bag or coil of contact happen,
replace them.
•
Do not drop down module of air bag or coil of
contact, do not contact module of air bag or coil of
contact over water, grease, and oil, if crack
deformation and corrosion are detected, replace
them, if module of air bag keep in the place, put
this on the even place, set the surface of pad on
the above, do not put anything on them, module of
air bag is not kept in the room temp 93 °C.
•
After air-bag is exploded, coil of contact and module
of air bag should be replaced. While exploded air
bag is treated, wear glove and glasses of protection.
•
In case for module of air bag not to explode, treat
as the procedure described.
•
While module of air bag and coil of contact are
separated, do not force them to push excessively.
•
Before coil of contact is not installed, after keep
front tire forward in align, keep in line between mark
of contact coil and mark of neutral and then install
contact coil. If mark of contact coil does not keep
in line properly, steering wheel does not revolve,
flat cable can be damaged, air bag does not operate
normally, so can cause driver to damage, if contact
coil is inspected any situation, refer to the section
of air bag.
•
If module of air bag is not blown, module of air bag
should be treated by procedure.
•
If module of air bag and connector of contact coil
are separated, excessive force does not be put in
those one.
•
Before contact coil is installed front wheel should
be aligned to the forward, mark on the contact coil
should keep on the one line with mark of NEUTRAL,
and then contact coil should be installed.
1. Separate negative terminal of battery.
2. Put direction of wheel on the forward and moving
direction of vehicle, after releasing screw (left and
right), remove module of air bag.
YAD9D480
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст